Download Report

Congratulations on your choice of a Hifonics subwoofer.
This “Quick Start Installation” guide is meant to help you
“hook up” and play music. For more detailed information
on system setting, speaker and subwoofer configuration,
and full specifications by model, visit the website at
Hifonics.com
Before you start
Recommended enclosures
It’s a good idea to confirm that you have purchased the
correct size subwoofers to fit your vehicle. If you have any
reservations about being able to complete the installation
yourself, we recommend contacting a professional. Be careful
as you go. Always disconnect the negative battery terminal
before starting any electrical work on the vehicle.
Sealed rectangle
BZE-10S4S BZE-12S4S
Enclosure types
CAUTION
Always consider consulting a professional audio installer
before installing new subwoofers. High power audio
systems have the ability create sound levels above 130dB.
Extended exposure to high sound pressure levels can
cause hearing damage.
Always run any new wiring through safe areas that wont
interfere with the normal operation of the vehicle.
Sealed
Sealed enclosures offer a range of performance
profiles depending on the internal air volume.
Larger enclosures will have a smoother more
extended response while a small enclosure
will have increased output in a more focused
frequency range. Sealed enclosures are the
simplest to construct but do require that the box
be completely air tight.
A
B
D
C
B
C
D
BZE-10S4S 10.24”(260)
3.11”(78)
9.17”(233)
6.22”(158)
BZE-12S4S 12.24”(311)
3.20”(81)
11.0”(280)
6.61”(168)
in(mm)
A
The internal volume of the
enclosure must be determined
to insure proper performance.
Simply measure height, width and
depth of enclosure you intend
to build. Subtract the material
thickness. Multiply these numbers
and divide by 1728 to get the
volume in cubic feet.
Enclosure
Volume
•
•
•
D
HxWxD
1728
D1 + D2
2
Width
17.5”
20.5”
Depth
8.5”
9.13”
Vb
.52 ft
F3
43.8 Hz
46.2 Hz
Qtc
.828
.918
3
.87 ft3
Height
11.5”
13.5”
Width
22.7”
27.8”
Depth 1
6.0”
6.0”
Depth 2
8.0”
8.0”
Vb
.52 ft3
.87 ft3
F3
43.8 Hz
46.2 Hz
Qtc
.828
.918
Enclosure construction
•
•
For enclosures with an angled
panel, measure the larger and
smaller depths, add these
together and divide by two. Use
this averaged depth.
13.5”
BZE-10S4S BZE-12S4S
Vented designs are NOT recommended. This
subwoofer is designed to perform in small
sealed enclosures.
Volume calculation
11.5”
Sealed wedge
Vented
Subwoofer dimensions
Height
Use 3/4” MDF
Make sure the woofer mounting panel is
full width and height
Glue all mating surfaces
Use wood screws
Use silicone caulk on all internal joints
Crossovers
Subwoofer specifications
Low Pass (LPF)
A Low pass filter will allow only
the bass frequencies to reach the
woofer making for a more natural
transition to the higher frequency
drivers. Check your amplifier’s
manual for details.
/3)
10Hz
100Hz
1000Hz
Subsonic
We recommend using an
electronic subsonic filter. This will
help to protect the woofer from
extreme low frequency distortion.
Many amplifiers are equipped
with this type filter. Check your
amplifier’s manual for details.
+]
68%621,&
10Hz
100Hz
1000Hz
Wiring
Connections
This subwoofer is equipped with
quick disconnect type terminals.
Use crimp type terminals or solder
the wire directly to the terminals.
+]
BZE-10S4S BZE-12S4S
NomZ
4.0
4.0
Sd
.034
.052
Ohm
sqM
Revc
3.550
3.600
Ohm
BL
11.138
11.684
TxM
Liters
Vas
37.049
102.600
Cms
217.485
264.365
uM/N
Mmd
103.058
131.923
Grams
Mms
106.765
138.796
Grams
Hz
Fo
33.029
26.274
Qms
8.698
8.331
Qes
0.634
0.604
Qts
0.591
0.563
no
0.204
0.298
%
SPL@1W
85.106
86.758
dB
Xmax
6.5
6.5
mm
RMS
150
150
Watts
Peak
300
300
Watts
Quick Start
Installation Guide
Configurations
Depending on the number of woofers you intend to use,
you can configure the wiring to provide the best impedance
load for your system. Below are some examples. Consult
your amplifier’s manual for recommendations.
2
8
4
4
4
4
4
4
4
4
4
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specifically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
Hifonics products are designed and engineered in the USA by
847-540-7700
www.maxxsonics.com
HF Elite wfr QSG 01 - rev2
BZE-10S4S
BZE-12S4S