DONGYANG UNITECH CO., LTD
DONGYANG UNITECH CO., LTD. 371-36, KASAN-DONG, KEUMCHEM-GU, SEOUL 153-803 REPUBLIC OF KOREA. TEL: +82 2 837 7233, FAX: +82 2 851 5146 www.d-max.co.kr / E-mail: sales@d-max.co.kr How to change protocol A) From D-MAX Protocol to PELCO-P protocol (4800 bps) First, to change protocol, it is set DIP switch on the address dip switch panel inside speed dome camera as below figure. 1. Turn off the power in the part A. 2. Turn on the DIP S/W 3 in the part C. It is changed to ‘INIT’ (it means turn on the dip s/w3). 3. Turn on the DIP S/W 1 and DIP S/W 8 in the part B. 4. Now, turn on the power switch, then it appears message on the monitor as follows: ‘PELCO P protocol, 4800 bps’ and so on. 5. Turn off the power again. 6. Turn off the DIP SW3 in the part C (switch is changed ‘INIT’ to ‘ADDR’) and turn off the DIP SW 1 & 8 in the part B. 7. If you want to make any address for the camera, please set the address number as desire in the part B. (If the camera is only, the camera is recognized address none) 8. Finally, please turn on the power switch in the part A. 9. Now you can use in the PELCO –P Protocol (4800 bps) based. -1- DONGYANG UNITECH CO., LTD. 371-36, KASAN-DONG, KEUMCHEM-GU, SEOUL 153-803 REPUBLIC OF KOREA. TEL: +82 2 837 7233, FAX: +82 2 851 5146 www.d-max.co.kr / E-mail: sales@d-max.co.kr B) From D-MAX Protocol to PELCO-P protocol (2400 bps) First, to change protocol, it is set DIP switch on the address dip switch panel inside speed dome camera as below figure. 10. Turn off the power in the part A. 11. Turn on the DIP S/W 3 in the part C. It is changed to ‘INIT’ (it means turn on the dip s/w3). 12. Turn on the DIP S/W 1 and DIP S/W 7 in the part B. 13. Now, turn on the power switch, then it appears message on the monitor as follows: ‘PELCO P protocol, 2400 bps’ and so on. 14. Turn off the power again. 15. Turn off the DIP SW3 in the part C (switch is changed ‘INIT’ to ‘ADDR’) and turn off the DIP SW 1 & 7 in the part B. 16. If you want to make any address for the camera, please set the address number as desire in the part B. (If the camera is only, the camera is recognized address none) 17. Finally, please turn on the power switch in the part A. 18. Now you can use in the PELCO – P Protocol (2400 bps) based. -2- DONGYANG UNITECH CO., LTD. 371-36, KASAN-DONG, KEUMCHEM-GU, SEOUL 153-803 REPUBLIC OF KOREA. TEL: +82 2 837 7233, FAX: +82 2 851 5146 www.d-max.co.kr / E-mail: sales@d-max.co.kr C) From D-MAX Protocol to PELCO-D Protocol (4800 BPS). First, to change protocol, it is set DIP switch on the address dip switch panel inside speed dome camera as below figure. 19. Turn off the power in the part A. 20. Turn on the DIP S/W 3 in the part C. It is changed to ‘INIT’ (it means turn on the dip s/w3). 21. Turn on the DIP S/W 2 and DIP S/W 8 in the part B. 22. Now, turn on the power switch, then it appears message on the monitor as follows: ‘PELCO D protocol, 4800 bps’ and so on. 23. Turn off the power again. 24. Turn off the DIP SW3 in the part C (switch is changed ‘INIT’ to ‘ADDR’) and turn off the DIP SW 2 & 8 in the part B. 25. If you want to make any address for the camera, please set the address number as desire in the part B. (If the camera is only, the camera is recognized address none) 26. Finally, please turn on the power switch in the part A. Now you can use in the PELCO – D Protocol (4800 bps) based. -3- DONGYANG UNITECH CO., LTD. 371-36, KASAN-DONG, KEUMCHEM-GU, SEOUL 153-803 REPUBLIC OF KOREA. TEL: +82 2 837 7233, FAX: +82 2 851 5146 www.d-max.co.kr / E-mail: sales@d-max.co.kr D) From D-MAX Protocol to PELCO-D (2400 bps) First, to change protocol, it is set DIP switch on the address dip switch panel inside speed dome camera as below figure. 27. Turn off the power in the part A. 28. Turn on the DIP S/W 3 in the part C. It is changed to ‘INIT’ (it means turn on the dip s/w3). 29. Turn on the DIP S/W 2 and DIP S/W 7 in the part B. 30. Now, turn on the power switch, then it appears message on the monitor as follows: ‘PELCO P protocol, 2400 bps’ and so on. 31. Turn off the power again. 32. Turn off the DIP SW3 in the part C (switch is changed ‘INIT’ to ‘ADDR’) and turn off the DIP SW 2 & 7 in the part B. 33. If you want to make any address for the camera, please set the address number as desire in the part B. (If the camera is only, the camera is recognized address none) 34. Finally, please turn on the power switch in the part A. Now you can use in the PELCO –P Protocol (2400 bps) based. -4- DONGYANG UNITECH CO., LTD. 371-36, KASAN-DONG, KEUMCHEM-GU, SEOUL 153-803 REPUBLIC OF KOREA. TEL: +82 2 837 7233, FAX: +82 2 851 5146 www.d-max.co.kr / E-mail: sales@d-max.co.kr E) From PELCO-P to PELCO-D First, to change protocol, it is set DIP switch on the address dip switch panel inside speed dome camera as below figure. 35. Turn off the power in the part A. 36. Turn on the DIP S/W 3 in the part C. It is changed to ‘INIT’ (it means turn on the dip s/w3). 37. Turn on the DIP S/W 2 and DIP S/W 7(2400 bps), or S/W 8(4800 bps) in the part B. 38. Now, turn on the power switch, then it appears message on the monitor as follows: ‘PELCO-D protocol, 2400 bps or 4800 bps’ and so on. 39. Turn off the power again. 40. Turn off the DIP SW3 in the part C (switch is changed ‘INIT’ to ‘ADDR’) and turn off the DIP SW 2, 7 or 8 in the part B. 41. If you want to make any address for the camera, please set the address number as desire in the part B. (If the camera is only, the camera is recognized address none) 42. Finally, please turn on the power switch in the part A. Now you can use in the PELCO–D Protocol (2400 or 4800 bps) based. -5- DONGYANG UNITECH CO., LTD. 371-36, KASAN-DONG, KEUMCHEM-GU, SEOUL 153-803 REPUBLIC OF KOREA. TEL: +82 2 837 7233, FAX: +82 2 851 5146 www.d-max.co.kr / E-mail: sales@d-max.co.kr F) From PELCO-D to PELCO-P First, to change protocol, it is set DIP switch on the address dip switch panel inside speed dome camera as below figure. 43. Turn off the power in the part A. 44. Turn on the DIP S/W 3 in the part C. It is changed to ‘INIT’ (it means turn on the dip s/w3). 45. Turn on the DIP S/W 1 and DIP S/W 7(2400 bps), or S/W 8(4800 bps) in the part B. 46. Now, turn on the power switch, then it appears message on the monitor as follows: ‘PELCO-P protocol, 2400 bps or 4800 bps’ and so on. 47. Turn off the power again. 48. Turn off the DIP SW3 in the part C (switch is changed ‘INIT’ to ‘ADDR’) and turn off the DIP SW 2, 7 or 8 in the part B. 49. If you want to make any address for the camera, please set the address number as desire in the part B. (If the camera is only, the camera is recognized address none) 50. Finally, please turn on the power switch in the part A. Now you can use in the PELCO–P Protocol (2400 or 4800 bps) based. -6- DONGYANG UNITECH CO., LTD. 371-36, KASAN-DONG, KEUMCHEM-GU, SEOUL 153-803 REPUBLIC OF KOREA. TEL: +82 2 837 7233, FAX: +82 2 851 5146 www.d-max.co.kr / E-mail: sales@d-max.co.kr G) From PELCO-P or D (2400 or 4800 bps) to D-MAX Protocol First, to change protocol, it is set DIP switch on the address dip switch panel inside speed dome camera as below figure. 51.Turn off the power switch in the part A. 52.Turn DIP SW 3 to ‘INIT’ in the part C. 53. If you already set the address dip switch in the part B, please all is off. 54. Turn on the power switch on the part A. 55. Now, it appears messages on the monitor as follows: “ DONGYANG UNITECH Protocol” and so on. 56. Turn off the power switch again and turn DIP SW3 in the part C (switch is changed ‘INIT’ to ‘ADDR’). 57. If you want to use address, please setup the address as desire in the part B. 58. Turn on the power switch in the part A. 59. Now, you can use the camera on the D-MAX Protocol based. -7- DONGYANG UNITECH CO., LTD. 371-36, KASAN-DONG, KEUMCHEM-GU, SEOUL 153-803 REPUBLIC OF KOREA. TEL: +82 2 837 7233, FAX: +82 2 851 5146 www.d-max.co.kr / E-mail: sales@d-max.co.kr H) From D-MAX Protocol to AD(American Dynamics) Protocol (4800 bps) First, to change protocol, it is set DIP switch on the address dip switch panel inside speed dome camera as below figure. 60. Turn off the power in the part A. 61. Turn on the DIP S/W 3 in the part C. It is changed to ‘INIT’ (it means turn on the dip s/w3). 62. Turn on the DIP S/W 1, DIP S/W 2 and DIP S/W 8 in the part B. 63. Now, turn on the power switch, then it appears message on the monitor as follows: ‘AD protocol, 4800 bps’ and so on. 64. Turn off the power again. 65. Turn off the DIP SW3 in the part C (switch is changed ‘INIT’ to ‘ADDR’) and turn off the DIP SW 1,2 & 8 in the part B. 66. If you want to make any address for the camera, please set the address number as desire in the part B. (If the camera is only, the camera is recognized address none). 67. Finally, please turn on the power switch in the part A. 68. Now you can use in the AD Protocol (4800 bps) based. -8- DONGYANG UNITECH CO., LTD. 371-36, KASAN-DONG, KEUMCHEM-GU, SEOUL 153-803 REPUBLIC OF KOREA. TEL: +82 2 837 7233, FAX: +82 2 851 5146 www.d-max.co.kr / E-mail: sales@d-max.co.kr I) The Figure of DIP SW for the protocol change Address DIP Switch panel Setting DIP Switch panel ON 1 2 3 4 5 6 7 8 1 2 3 4 5 OFF PELCO-D 4800 bps ‘INIT’ SW PELCO-P 2400 bps AD You should combine with the DIP switch to change protocols as follows. 1 + 8 + 3 = PELCO-P (4800 bps) 1 + 7 + 3 = PELCO-P (2400 bps) 2 + 8 + 3 = PELCO-D (4800 bps) 2 + 7 + 3 = PELCO-D (2400 bps) 1+2+8+3 = AD (4800 bps) Caution : After converting the protocol as desired, do not make ‘address no.(0)’ on the speed dome. Because of the address no. (0) is available for D-MAX protocol only. If you make a setting on Pelco by one dome, please make address no.(1) on the dome. -9-
© Copyright 2024