Download Report

Submittal Review Cover Sheet
Project#: 11DB-C5-08-61-02-PS14
Project: 11-13-07 Fire Station # 2
Date:
Submittal#:
Architect#
12/26/13
5
Revision#
0
Owner#
1312 Bowman Street
Clermont, FL 34711
Phone (352) 394-1032
To:
Fax: (352) 394-1794
Submitter: Kevin Boutros
City of Zephyrhills
5335 8th Street
Zephyrhills, FL 33540
Phone: (813) 780-0022
Fax:
(813) 780-0025
Our Job#:
50041
Sub or Supplier
WE Supply Division 10, LLC
656 Wyckliffe Place,
Winter Springs, FL 32708
Contact: Shane LeBlanc
Spec#
102800-1
Paragraph Spec Description
DIVISION 10 (Accessories)
Item Name
DIVISION 10 (Accessories)
Item Type
Comment
Reason:
Reviewed By
Pillar Construction Group, LLC
Review is for general design only. Subcontractor and or Supplier are responsible for dimensions, quantities, and full
compliance with the requirements of the contract documents. Review or approval by the architect or engineer does not
relieve the Subcontractor and or Supplier of the responsibilities required by the terms and conditions of the agreement
with Pillar Construction Group, LLC.
Date:
By:
AREA FOR OTHER REVIEW STAMPS AND COMMENTS:
PILLAR CONSTRUCTION GROUP, LLC
Date 12/26/13
By: Kevin Boutros
No Exception Taken
Make Corrections Noted
Revise & Resubmit
Rejected
This shop drawing review is for general
performance with contract documents only and
does not relieve the subcontractor or fabricator
of his responsibility for compliance with
requirements of the drawings and specifications.
Submittal#
5
Spec Section# 102800-1
Drawing#
Form: SubOne-G1
12/26/13
ABC Magnetic Dry Erase Board (12’ W x 4” H)
Writing Surface :
Porcelain-on-steel
Magnetic:
Yes
Backing Material:
1/4" hardboard
Frame Material:
Aluminum
Tray Material:
Aluminum w/ plastic end caps
Warranty:
50 years
Other Info:
Comes w/ a set of dry erase
markers & mounting hardware.
Greenguard certified.
Width:
12'
Height:
4'
Assembly:
Installation required
Weight:
148.0 lbs.
Shipping Method:
Freight
Best-Rite's ABC Magnetic Dry Erase Board is an affordable addition to your classroom.
This porcelain-on-steel dry erase board accepts magnets, so you can easily hang
classroom assignments, visual aids and art projects. The low-gloss writing surface
offers a greater contrast for markers, resists ghosting and carries a 50-year guarantee.
An aluminum tray keeps writing supplies close at hand and features protective end caps
that help prevent classroom injuries. Greenguard certification lets you feel good about
using this markerboard in your room. All Best-Rite ABC Magnetic Dry Erase Boards
come with a free set of dry erase markers.
DESIGNER CONTOUR ®
ELECTROL®
Automatic Electric Projection Screen Model
SPECIFICATION DATA
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com
SUGGESTED SPECIFICATIONS: ___________________ projection screen(s), ______________ (H) x ______________ (W), electrically
operated 120 volt (60 Hz) not more than 1.2 amp. Shall have specially designed motor mounted inside the roller, to be three wire with
ground, quick reversal type, oiled for life, with automatic thermal overload cutout, integral gears, capacitor and an electric brake to
prevent coasting. To have preset but adjustable limit switches to automatically stop the picture surface in the “up” and “down”
positions. The roller to be of rigid metal. Roller mounting brackets to be adjustable to allow centering or offsetting of the screen within
the case. Screen case to be a two piece design made of extruded aluminum. Case to be finished in white, lightly textured powder
coat. Screen fabric to be flame retardant and mildew resistant fiberglass with black masking borders standard. Bottom of fabric shall
be formed into a pocket holding a metal rod. Screen to include a three-position control switch and cover plate. Screen to be listed by
Underwriters’ Laboratories.
Matte White, High Contrast Matte White and Video Spectra 1.5: Seamless in all sizes.
High Power®: Horizontal seam required when both dimensions exceed 6'.
VIDEO (NTSC 4:3) FORMAT DIMENSIONS (2" standard black drop at top)
Viewing
Nominal
Overall
Approx. Ship.
Area
Diagonal
Length of Case
Wt.
HxW
Cm
In.
Cm
In.
Cm
Lbs.
Kg
43" x 57"
109 x 145
72"
183
691/4"
176
34
15.4
50" x 67"
127 x 170
84"
213
791/4"
201
37
16.8
57" x 77"
145 x 196
96"
244
931/4"
237
42
19.1
60" x 80"
152 x 203
100"
254
931/4"
237
42
19.1
69" x 92"
175 x 234
120"
305
1051/4"
267
47
21.3
HDTV (16:9) FORMAT DIMENSIONS (2" standard black drop at top)
Viewing
Nominal
Overall
Approx. Ship.
Area
Diagonal
Length of Case
Wt.
HxW
Cm
In.
Cm
In.
Cm
Lbs.
Kg
371/2" x 67"
95 x 170
77"
196
791/4"
201
37
16.8
45" x 80" 114 x 203
92"
234
931/4"
237
42
19.1
52" x 92" 132 x 234 106"
269
1051/4"
267
47
21.3
SQUARE FORMAT DIMENSIONS (screens with ^ have 2" standard black drop at top)
Overall
Approx. Ship.
Sizes
Length of Case
Wt.
HxW
Cm
In.
Cm
Lbs.
Kg
50" x 50"
127 x 127
591/4"
150
28
12.7
60" x 60"
152 x 152
691/4"
176
34
15.4
70" x 70"
178 x 178
791/4"
201
37
16.8
84" x 84"
213 x 213
931/4"
237
42
19.1
6' x 8'^
183 x 244
1051/4"
267
47
21.3
8' x 8'
244 x 244
1051/4"
267
48
21.8
Overall case length dimensions ±1/4".
Detail dimensional drawings, wiring diagrams and installation instructions available upon request.
Specifications subject to change without notice.
Custom formats and sizes available upon request.
C
WHEN ORDERING, MARK APPROPRIATE SELECTIONS:
Select size from charts on the other side.
Select viewing surface:
✔
❏
Matte White
❏ High Contrast Matte White
❏ High Power®
❏ Video Spectra 1.5
Greenguard® and Greenguard® Children and Schools Certified.
Optional Accessories:
❏ No borders (Black masking borders standard).
❏ Single Motor Low Voltage Control (LVC) – external.
❏ Single Motor Low Voltage Control (LVC) – built in (adds 5" to length of case).
❏ Wireless Remote Control for LVC.
❏ Radio Frequency Remote.
❏ Radio Frequency Range Extender available
❏ Infrared Remote.
❏ Key Locking Cover Plate for 120 V Switch or LVC Switch.
❏ Key Operated Switch for 120 V only (Note: Cannot be used with LVC).
❏ 220 Volt (50 Hz) Motor.
❏ Video Projector Interface Control - external.
❏ External SCB-100 - RS-232 Serial Control Board
❏ NET-100 Ethernet-Serial Adapter
❏ Veneer Case Cover (Choose from seven standard veneers).
❏ Light Oak
❏ Medium Oak
❏ Natural Walnut
❏ Heritage Walnut
❏ Mahogany
❏ Cherry
❏ Honey Maple
❏ Graphite case color.
❏ Black case (white standard).
Project:
Zephyrhills FS#2
Architect:
Phone:
Contractor: WE Supply Division 10, LLC
Phone:
Supervisor:
Phone:
Supplier:
Date:
Revised:
DESIGNER CONTOUR® ELECTROL®
METHODS OF INSTALLATION
CEILING/HOOK MOUNT BRACKET
CASE HOOK
41/4"
/16"
5
/16"
9
WALL MOUNT
BRACKET
5 /8"
1
45/8"
HOOK MOUNT HOLE
43/32"
CEILING MOUNT HOLES
Rev. 2/08
1 each
CONTURA™ SERIES
SURFACE-MOUNTED
SANITARY NAPKIN DISPOSAL
gg
gg
MM
3
B-270
&INISH&ACEOF7ALL
MM
gg
MM
4YP
gg
MM
Patented
ggTOggTOMM
3
(INGED,ID
2ECOMMENDED-OUNTING(EIGHT/FF&LOOR
&OR5NIVERSAL"ARRIER&REE$ESIGN
4YP
gg
MM
MATERIALS:
Container — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel. All-welded construction. Exposed surfaces have satin finish.
Integral finger depression for opening cover. Front of container has same degree of arc as front of cover and other Bobrick
Contura Series washroom accessories. Radius on side edges of container match corners and edges of cover and other
Contura Series accessories.
Cover — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn, one-piece, seamless construction. Front
of cover has same degree of arc as front of container and other Bobrick Contura Series washroom accessories. Radius on
corners and edges of cover match side edges of container and other Contura Series accessories. Secured to container with a
full-length stainless steel piano-hinge.
OPERATION:
Cover flips up for disposal of sanitary napkins and for servicing container. Disposable paper liners for the container are
available as an optional accessory: order Bobrick Part No. 270-12.
INSTALLATION:
For partitions with particle-board or other solid core, secure with two #8 x 3/4'' (4.2 x 19mm) sheet-metal screws (not
furnished) at all points indicated by an S, or provide through-bolts, nuts, and washers.
For hollow-core metal partitions, provide solid backing into which sheet-metal screws can be secured. If two units are
installed back-to-back, then provide threaded sleeves and machine screws for the full thickness of partition.
For masonry walls, provide fiber plugs or expansion shields for use with sheet-metal screws, or provide 3/16" (5mm) toggle
bolts or expansion bolts.
For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with
sheet-metal screws.
SPECIFICATION:
Surface-mounted sanitary napkin disposal shall be type-304 stainless steel with all-welded construction; exposed surfaces
shall have satin finish. Front of sanitary napkin disposal shall have same degree of arc and match other Bobrick Contura™
Series accessories in the washroom. Radius on corners and edges of sanitar y napkin disposal shall complement other
Bobrick Contura™ Series washroom accessories. Cover shall be drawn, one-piece, seamless construction and secured to
container with a full-length stainless steel piano-hinge. Container shall have integral finger depression for opening cover.
Manufacturer's service and parts manual shall be provided to the building owner/manager upon completion of project.
Surface-Mounted Sanitar y Napkin Disposal shall be Model B-270 of Bobrick Washroom Equipment, Inc.,
Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company,
Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment
Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.
Revised 5/06
Printed in U.S.A.
© 2006 by Bobrick Washroom Equipment, Inc.
2 each
Technical Data
ClassicSeries™
surface-mounted
SOAP DISPENSER
B-2112
8-1/8''
S S
Concealed
Wall Plate
S
4-3/4''
Window
120mm
S
Push Button
& Spout
Patented
2-3/4''
70mm
3-1/2''
90mm
47-1/2'' 1205mm
S
Recommended Mounting Height Off Floor
For Universal / Barrier-Free Design
Finish Face of Wall
Filler-Top
205mm
materials:
Container — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin-finish. Body is drawn, one-piece, seamless
construction. Back plate has mounting bracket attached. Furnished with concealed wall plate. Equipped with an unbreakable,
clear acrylic soap refill-indicator window and a locked, hinged stainless steel lid for top filling. Capacity: 40-fl oz (1.2-L).
Valve — Black molded plastic push button and spout. Soap head-holding mushroom valve. Stainless steel spring. U-packing
seal and duckbill. Corrosion-resistant to most soaps and detergents. CAUTION: Valve does not dispense antibacterial soaps.
operation:
Corrosion-resistant valve dispenses commercially marketed all-purpose hand soaps. To prevent corrosion, use only chloridefree pH-netural liquid soaps. Valve is operable with one hand, without tight grasping, pinching, or twisting of the wrist, and with
less than 5 pounds of force (22.2 N) to comply with barrier-free accessibility guidelines (including ADAAG in U.S.A.). Window
indicates when refill is required. The locked, hinged lid opens for top filling only with special key provided. Concealed, vandalresistant mounting.
installation:
Secure wall plate to the wall with three sheet-metal screws, furnished by manufacturer, at points indicated by an S. Slide
mounting bracket of container down onto wall plate and secure unit with furnished locking-screw. For plaster or dry wall
construction, provide concealed backing to comply with local building codes and secure with sheet-metal screws furnished.
For other wall surfaces, provide fiber plugs or expansion shields for use with sheet-metal screws furnished, or provide 1/8"
(3mm) toggle bolts or expansion bolts.
Note: Surface-mount the dispenser plumb and true with valve 6'' (150mm) to right or left of lavatory center. Provide 4''
(100mm) minimum clearance from the lid to the underside of any horizontal projection. Push buttons should be located 44"
(1120mm) maximum above the finish floor.
specification:
Surface-mounted soap dispenser shall be type-304 stainless steel with satin-finish. Corrosion-resistant valve shall dispense commercially marketed all-purpose hand soaps. To prevent corrosion, use only chloride-free pH-netural liquid soaps. Valve shall
be operable with one hand and with less than 5 pounds of force (22.2 N) to comply with barrier-free accessibility guidelines
(including ADAAG in U.S.A.). Container shall be equipped with a clear acrylic soap refill-indicator window; a locked, hinged
stainless steel lid for top filling; and shall have a capacity of 40-fl oz (1.2-L). Unit shall have concealed, vandal-resistant mounting. Manufacturer’s service and parts manual shall be provided to the building owner/manager upon request.
Surface-Mounted Soap Dispenser shall be Model B-2112 of Bobrick Washroom Equipment, Inc., Clifton Park,
New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough,
Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United
Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.
Revised 12/08
Printed in U.S.A.
© 2008 by Bobrick Washroom Equipment, Inc.
Technical Data
MIRROR WITH
STAINLESS STEEL
ANGLE FRAME
B-2906
B-2908
B-2909
SPECIAL-ORDER REFLECTIVE SURFACES
Specify Series Required:
SNAP LOCKING DESIGN
(Rear View)
SCREW LOCKING DESIGN
(Rear View)
3/4''
19mm
2-1/2''
65mm
2-7/16''
60mm
S
S
1-15/16''
45mm
S
2-9/16''
S
65mm
3"
4'' or 5" Typ.
100 or 125mm
75mm
S
S
T
Frame
Mirror
Locking Screw
(Phillips-Head)
Side View
Back Plate/Wall Hanger
Figure: 1

2 each
Figure: 2
B-2908 Series Tempered Glass Mirror
Standard Sizes —
B-2908 1830 18" x 30" (46 x 76cm)
B-2908 1836 18" x 36" (49 x 91cm)
B-2908 2436 24" x 36" (61 x 91cm)

B-2906 Series Polished Stainless Steel
Mirror —
72" x 24" (183 x 61cm) or
24" x 48" (61 x 122cm) maximum;
12" x 12" (30 x 30cm) minimum.

B-2908 Series Tempered Glass Mirror —
120" x 48" (305 x 122cm) or
48" x 60" (122 x 152cm) maximum;
16" x 20" (41 x 51cm) minimum.

B-2909 Series Laminated Glass Mirror —
96" x 48" (244 x 122cm) maximum
12" x 12" (30 x 30cm) minimum.
Designer's Notes:
1.
Special-order only.
2.
All Bobrick framed mirrors are manufactured to overall width and height dimensions. EXAMPLE: A 24" x 36" (61 x 91cm) mirror will be furnished 24" x 36"
(610 x 915mm) outside-of-frame to outside-of-frame.
3.
To specify sizes use Series Number followed by width then height in inches. EXAMPLE: B-2906 2024.
4.
Bobrick framed mirrors are manufactured to a tolerance ±1/8" (3.2mm).
5.
For sufﬁcient space to lift mirror onto wall hanger(s), provide 3-1/4" (85mm) minimum clearance above center line of mounting screw holes.
6.
Provide 1" (25mm) minimum clearance at bottom of mirror for engaging locking screws and 1" (25mm) clearance on each side.
MATERIALS:
Frame — 18-8 S, type-304, heavy-gauge stainless steel, 3/4" x 3/4" (19 x 19mm) angle with vertical-grain satin ﬁnish. Onepiece, roll-formed construction forms continuous integral stiffener on all sides. Bevel design on front of angle holds frame
tightly against mirror. Corners are welded, ground, and polished smooth. Galvanized steel back is fastened to frame with
concealed screws and equipped with integral horizontal hanging brackets. Concealed Phillips-head locking screws securely
fasten mirror to wall hanger(s).
Designer's Note: Type 304 stainless steel provides superior corrosion resistance, compared to 400 Series stainless steel, against
enviromental moisture, hose-down maintenance and strong cleaning solution.
continued . . .
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.
Revised 2/16/11 R/B
Printed in U.S.A.
© 2011 by Bobrick Washroom Equipment, Inc.
Mirror — (B-2906 Series) Stretcher leveled stainless steel with reﬂective, highly polished strip ﬁnish. Tempered masonite
backing.
(B-2908 Series) No. 1 quality, 1/4" (6mm) tempered select ﬂoat glass: selected for silvering and electrolytically
copper-plated by the galvanic process.
(B-2909 Series) 1/4" (6mm) thick. Two pieces of 1/8" (3mm) select ﬂoat glass: selected for silvering, laminated
with 0.003'' (0.08mm) thick clear vinyl in the center, and electrolytically copper-plated by the galvanic process.
Note: These reﬂective surfaces resist breakage and provide a measure of safety from broken glass, but differ in
color and reﬂective quality from standard glass mirrors.
All edges protected by plastic ﬁller strips. Backs of all glass mirrors are protected by full-size, shock-absorbing,
water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding.
Concealed Wall Hanger(s) — 20-gauge (0.9mm) galvanized steel. incorporates lower support member forming rigid
rectangle, which engages lower backplate louvers to keep bottom of mirror against wall.
INSTALLATION:
Mount wall hanger on wall with screws (not furnished) at points indicated by an S. For plaster or dry wall construction, provide
concealed backing to comply with local building codes, then secure wall hanger with screws (not furnished). For other wall
surfaces, provide ﬁber plugs or expansion shields for use with screws (not furnished), or provide 1/8" (3mm) toggle bolts or
expansion bolts. Hang mirror on wall hanger. Lock mirror to wall hanger by tightening Phillips-head locking screws that are
concealed in bottom of frame at points indicated by a T.
Snap Locking Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into ﬁnal
position (see ﬁgure 3). Locking devices may be unlocked by inserting two ﬂat blade screwdrivers behind each side of mirror
near the bottom or under the bottom of the mirror and pulling mirror bottom forward and then up.
Screw locking Design — Lock mirror to wall hanger by tightening Phillips-head locking screws that are concealed in the
bottom of frame at points indicated by a T (see ﬁgure 4). Mirror may be unlocked from wall hanger by loosening locking
screws and lifting mirror off of concealed wall hanger.
SNAP LOCKING DESIGN
(Front View)
Approx. 1"
(25mm)
CL
SCREW LOCKING DESIGN
(Front View)
Approx. 1"
(25mm)
Initial
Position
CL
Initial
Position
Final
Position
Final
Position
S
S
S
S
T
Figure: 3
T
Figure: 4
SPECIFICATION:
Mirror shall have a one-piece type 304 stainless steel angle frame, 3/4" x 3/4" (19 x 19mm) with continuous integral stiffener
on all sides and beveled front to hold frame tightly against mirror; corners shall be welded, ground, and polished smooth; all
exposed surfaces shall have satin ﬁnish with vertical grain. Mirror shall be __________________________ (insert one: polished
stainless steel, tempered glass, or laminated glass). All edges shall be protected by plastic ﬁller strips. Backs of all glass
mirrors shall be protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding.
Galvanized steel back shall have integral horizontal hanging brackets located at top for mounting on concealed rectangular wall
hanger. Mirror shall be secured to wall hanger with concealed Phillips-head locking screws located in bottom of frame.
Framed Mirror shall be Model _______________ (insert model number) of Bobrick Washroom Equipment, Inc.,
Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company,
Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment
Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.
QA02
B-2906 r2/16/11 R/B
Printed in U.S.A.
© 2011 by Bobrick Washroom Equipment, Inc.
2 each
Technical Data
ConturaSeries®
SURFACE-MOUNTED
PAPER TOWEL DISPENSER
B-4262
Finish Face of Wall
3''
75mm
Typ.
12-1/2''
320mm
13-1/2''
345mm
S
13-1/4''
335mm
Stainless
Steel Door
8''
205mm
Typ.
TowelMate
Towel Guide
Bracket Return
TowelMate
Towel Rod
S
66'' to 70'' 1675 to 1780mm
S
4-7/8''
125mm
1/8''
3mm
Lock & Key
Recommended Mounting Height Off Floor
1-5/8''
40mm
Typ.
10-13/16''
275mm
MATERIALS:
Cabinet — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel. All-welded construction. Exposed surfaces have satin finish. Radius on
corners of cabinet match corners and edges of door and other Bobrick ConturaSeries washroom accessories. Back has recessed mounting
slots to prevent mounting screw heads from snagging towels. Rounded towel tray has hemmed opening to dispense paper towels without
tearing. Cabinet inside equipped with 90° return towel guide bracket to prevent paper towels from falling forward out when door is opened
for servicing. Unit equipped with TowelMate consisting of a 90° return towel guide angle inside cabinet to prevent paper towels from falling
forward out when door is opened for servicing and a Nylon Rod across the center of the towel tray to dispense paper towels one at a time.
Equipped with a tumbler lock keyed like other Bobrick washroom accessories. Unit shall be capable of dispensing 400 C-fold or 525 multifold
paper towels 2-1/2" to 3-13/16" (64–97mm) deep.
Door — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn, one-piece, seamless construction. Front of door has
same degree of arc as other Bobrick ConturaSeries washroom accessories. Radius on corners and edges match corners of cabinet and other
ConturaSeries accessories. Secured to cabinet with a full-length stainless steel piano-hinge.
TowelMate® Towel Rod Assembly — Consisting of a round Nylon Rod and (2) stainless steel Rod Screws for attachment, is field
replaceable. Stainless steel Stop Screws (2) lock TowelMate Rod assembly in place. To retrofit TowelMate into existing installed units
manufactured prior to June 2010, order TowelMate Accessory Bobrick Model No. 369-130.
OPERATION:
Unit dispenses C-fold or multifold paper towels 2-1/2" to 3-13/16" (64–97mm) deep without adjustment or use of adapters.
Load paper in towel tray, and then pull one sheet of paper towel over the TowelMate towel rod and out to conceal rod and start
dispense. Slots in sides of cabinet indicate refill time. After unlocking with key provided, door swings down for loading paper
towels into cabinet.
INSTALLATION:
Mount unit on wall with four #10 x 1-1/4" (4.8 x 32mm) sheet-metal mounting screws (not furnished) at points indicated by
an S. For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit
with sheet-metal screws. For other wall surfaces, provide fiber plugs or expansion shields for use with sheet-metal screws, or
provide 1/8" (3mm) toggle bolts or expansion bolts.
SPECIFICATION:
Surface-mounted paper towel dispenser shall be type-304 stainless steel with all-welded construction; exposed surfaces
shall have satin finish. Front of paper towel dispenser door shall have same degree of arc as other Bobrick ConturaSeries
accessories in the washroom. Radius on corners and edges of door and cabinet shall complement other Bobrick ConturaSeries
washroom accessories. Unit equipped with TowelMate consisting of a 90° return towel guide bracket inside cabinet to prevent
paper towels from falling forward out when door is opened for servicing and a Nylon Rod across the center of the towel tray
to dispense paper towels one at a time. Door shall be drawn, one-piece, seamless construction; secured to cabinet with a fulllength stainless steel piano-hinge; and equipped with a tumbler lock keyed like other Bobrick washroom accessories. Unit
shall be capable of dispensing 400 C-fold or 525 multifold paper towels 2-1/2" to 3-13/16" (64–97mm) deep without adjustment
or use of adapters.
Surface-Mounted Paper Towel Dispenser shall be Model B-4262 of Bobrick Washroom Equipment, Inc.,
Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company,
Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment
Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.
B-4262 Rev. 4/27/11
Printed in U.S.A.
© 2011 by Bobrick Washroom Equipment, Inc.
1½" (38mm) DIAMETER
STAINLESS STEEL GRAB
BARS WITH SNAP FLANGE
7HFKQLFDO'DWD
B-6806
SERIES
Satin ﬁnish
Satin ﬁnish with peened gripping surface; add sufﬁx .99 to model number
Specify Finish Required:
(2) 36" each
(2) 42" each
Intermediate Flange
End Mounting Flange
2''
2-5/8''
50mm
65mm
3-1/8''
3-1/8''
80mm
80mm
2-1/4''
2-1/4''
55mm
55mm
1-1/2''
38mm
Snap Flange Cover
3-1/4''
3-1/8''
85mm
80mm
Dia.
5/16''
8mm
4''
100mm
36''
50''
915mm
1270mm
39-7/8''
1005mm
57-7/8''
1470mm
Edge of
Flange to Wall
TWO-WALL WHEELCHAIR
TOILET COMPARTMENT
VERTICAL
HORIZONTAL
B-6806 x 12, 18, 24, 30, 36, 42, 48
4''
4''
4''
24''
510mm
32''
B-68137
100mm
100mm
100mm
Edge of
Flange to Wall
42''
15-7/8''
1065mm
405mm
50''
26-7/8''
815mm
1270mm
685mm
27-7/8''
39-7/8''
710mm
45-7/8''
19-3/4''
1215mm
500mm
1015mm
Edge of
Flange to Wall
Edge of
Flange to Wall
34-3/4''
885mm
Edge of
Flange to Wall
57-7/8''
1470mm
Edge of
Flange to Wall
Edge of
Flange to Wall
Edge of
Flange to Wall
HORIZONTAL TUB BATH
24 x 36
HORIZONTAL TWO-WALL BAR
for Shower Stall
TWO-WALL
TOILET COMPARTMENT BAR 42 x 54
B-68616
B-6861
B-6897
continued . . .
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.
Rev. 5/5/10 S/B
Printed in U.S.A.
© 2010 by Bobrick Washroom Equipment, Inc.
MATERIALS:
Grab Bar — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel tubing with satin-ﬁnish. 1-1/2" (38mm) outside diameter. Ends are heliarc welded to ﬂanges.
Clearance between the grab bar and wall is 1-1/2" (38mm).
Concealed Mounting Flanges — 18-8 S, type-304, 1/8" (3mm) thick, stainless steel plate; end ﬂanges 2" x 3-1/8" (50 x 80mm) with two holes for attachment
to wall. Intermediate ﬂanges 2-5/8" x 3-1/8" (65 x 80mm) wide x 3-1/8" (80mm) diameter.
Snap Flange Covers — 18-8 S, type-304, 22-gauge (0.8mm) drawn stainless steel with satin-ﬁnish. 3-1/4" (85mm) diameter x 1/2" (13mm) deep. Each cover
snaps over mounting ﬂange to conceal mounting screws.
STRENGTH:
Bobrick grab bars that provide 1-1/2" (38mm) clearance from wall can support loads in excess of 900 pounds (408kg) if properly installed. Other grab bar
conﬁgurations can support loads in excess of 250 pounds (113kg) if properly installed, complying with barrier-free accessibility guidelines (including ADAAG
in the U.S.A.) for structural strength
Warning: Grab bars are no stronger than the anchors or walls to which they are attached and, therefore, must be ﬁrmly secured in order to support the loads for
which they are intended.
INSTALLATION:
Provide concealed anchor device or backing as speciﬁed or required in accordance with local building codes before wall is ﬁnished. Fasten concealed mounting ﬂanges to anchor device or backing with two screws in each ﬂange. Snap ﬂange covers over each mounting ﬂange to conceal mounting screws. Concealed
anchor devices and mounting screws are not included with Bobrick grab bars and must be speciﬁed as an accessory.
For Grab Bars with an Intermediate Flange(s), Pull Snap-Flange Covers away from mounting ﬂanges. Place grab bar in desired mounting location. Use
intermediate ﬂange as a template to mark location of mounting screws at intermediate ﬂange only. Mark screw locations at the center of the slot in the middle
of the double-keyhole shaped mounting holes (2) in the intermediate ﬂange. Remove grab bar from wall. Drive the intermediate ﬂange mounting screws into
wall at marked locations. Note: Make sure to leave a space of just over 1/8'' (3.17mm) between the underside of the screw head and the wall. install grab
bar on the wall by placing the round ends of the intermediate ﬂange double-keyhole shaped mounting holes over the mounting screws (2) are located in the
middle of the ﬂange slots. Install the mounting screws into the wall at the end ﬂanges and secure tightly. Tighten the mounting screws at the intermediate
ﬂange. Press all snap-ﬂange covers into place to conceal mounting ﬂanges.
Note: Recommend use of 1/4'' or #14 (M6.3) sheet metal or wood screws to install Intermediate Flange. #12 (M5.5) screws may also be used.
Important Notes:
1. Mounting Kits — Bobrick has a selection of mounting screws and fasteners available for different types of installations; one Bobrick mounting kit is
required for each ﬂange.
Mounting Kit No.
Description
252-30
Consists of (3) #14 x 2½'' (M6.3 x 64mm) type-304 stainless steel,
Phillips round-head, sheet-metal screws.
2521-30
Consists of (3) 1/4''–20 x 3½'' (M6.3–1 x 89mm) type-304 stainless steel, Phillips
round-head, machine screws with plated-steel toggle nuts.
2522-30
Consists of (3) 1/4''–20 x 2'' (M6.3–1 x 51mm) type-304 stainless steel, Phillips
round-head, machine screws with metal expansion shields.
2. Grab Bar Fastener — Bobrick has a grab bar fastening system that secures all Bobrick grab bar series; one Bobrick fastener is required for each
ﬂange. Install grab bar without backing in wall requires minimum 5/8" (16mm) thick painted or tiled drywall.
WingIt™ Fastener No.
251-4
Description
Consists of (3) 10–32 x 5/16'' round-head, Phillips 18/8 stainless steel
screws. (1) WingIt grab bar fastener.
3. Optional Anchor Device — Bobrick grab bar anchor device includes stainless steel machine screws to be used for attaching grab bars to anchors. one
Bobrick concealed anchor device is required for each ﬂange.
Optional Anchor No.
Description
2583
Anchor for 3/4" to 1" (19-25mm) panel
1 anchor required for each ﬂange.
2586
Anchor for 1/2" to 1" (13mm) panel
1 anchor required for each ﬂange.
SPECIFICATION:
Grab bar shall be type-304 stainless steel with satin-ﬁnish. Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/2" (38mm) outside diameter.
Clearance between the grab bar and wall shall be 1-1/2" (38mm). Concealed mounting ﬂanges shall be 1/8" (3mm) thick stainless steel plate, 2" x 3-1/8"
(50 x 80mm), and equipped with two screw holes for attachment to wall. Flange covers shall be 22 gauge (0.8mm), 3-1/4" (85mm) diameter x 1/2" (13mm)
deep, and shall snap over mounting ﬂange to conceal mounting screws and/or WingIt fasteners. Ends of grab bar shall pass through concealed mounting
ﬂanges and be heliarc welded to form one structural unit. Grab bar shall comply with barrier-free accessibility guidelines (including ADAAG in the U.S.A.) for
structural strength.
Grab Bar shall be Model __________ (insert model number) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson,
Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd.,
Australia; and Bobrick Washroom Equipment Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.
B-6806 Rev. 5/5/10 S/B QA0510 Printed in U.S.A.
© 2010 by Bobrick Washroom Equipment, Inc.
2 each
Technical Data
DOUBLE-ROLL
TOILET TISSUE DISPENSER
S
S
S
B-27460
S
5-1/4''
135mm
4-1/8''
105mm
Mounting Bracket
14-1/8''
85mm
Typ.
Typ.
360mm
Lock & Key
2-1/4''
55mm
Spindles
5/8''
16mm
Typ.
20-1/8'' 510mm
3-5/16''
45mm
Recommended Mounting Height
for Universal/Barrier-Free Design
1-3/4''
MATERIALS:
Bracket — Heavy-duty cast aluminum with satin finish. Equipped with a tumbler lock that is keyed like other Bobrick
washroom accessories.
Spindles (2) — Molded high-impact ABS.
OPERATION:
Accommodates two standard-core toilet tissue rolls up to 6" (152mm) diameter (2000 sheets). Tumbler lock secures spindles in
place; spindles can only be removed after unlocking with key furnished. Vandal-resistant.
INSTALLATION:
For partitions with particle-board or other solid core, provide sheet-metal screws or through-bolts, nuts, and washers.
For hollow-core metal partitions, provide solid backing into which sheet-metal screws can be secured. If two units are installed
back-to-back, then provide threaded sleeves and machine screws for the full thickness of partition.
For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with
sheet-metal screws.
For masonry walls, provide sheet-metal screws and fiber plugs or expansion shields, or provide 1/8" (3mm) toggle bolts or
expansion bolts.
SPECIFICATION:
Double-roll toilet tissue dispenser shall have a heavy-duty cast-aluminum bracket with satin finish. Bracket shall be equipped
with a tumbler lock to secure spindles in place. Vandal-resistant spindles shall be molded high-impact ABS. Unit shall
accommodate two standard-core toilet tissue rolls up to 6" (152mm) diameter (2000 sheets).
Double-Roll Toilet Tissue Dispenser shall be Model B-27460 of Bobrick Washroom Equipment, Inc., Clifton
Park, New York; Jackson Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company,
Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment
Limited, United Kingdom.
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions.
Revised 4/27/11
Printed in U.S.A.
© 2011 by Bobrick Washroom Equipment, Inc.
SUBMITTAL: FIRE EXTINGUISHERS
GRENADIER EXTINGUISHERS - PRESSURIZED WATER
Pressurized Water Extinguishers for Class "A" Fires. The “water press”
extinguisher contains water and compressed air. Units shipped empty.
Operation: Squeeze the lever, which opens the valve, allowing the water to be forced out.
Upright squeeze grip operation.
Construction: Butt-welded 304-L stainless steel cylinder (eliminates all internal and external
crevices). Rugged stainless steel discharge lever and fixed carry handle with visual pressure
gauge, pull pin. Heavy-duty, brass, chrome-plated valve body with replaceable molded valve
stem seal. UL labeled chemical engine hose.
CLASS A Fires
COSMIC & 495 EXTINGUISHERS - MULTI PURPOSE CHEMICAL
These units contain specially fluidized and siliconized mono ammonium
phosphate powder, which smothers and breaks the chain reaction on
Class B fires, fuses and insulates Class A fires and is a non-conductor of
electricity. Non-toxic.
Operation: Squeeze the lever, which opens the valve, allowing the chemical to be forced out.
Upright squeeze grip operation approved to -65°F (-52°C).
Construction: Heavy-duty steel cylinder with rugged metal valve and siphon tube with replaceable molded valve stem seal, visual pressure gauge, pull pin and upright squeeze grip. Corrosion and impact-resistant powder coat finish.
CLASS A,B,C Fires
PAGE 1 OF 2
GALAXY & 496 EXTINGUISHERS - REGULAR DRY CHEMICAL
These models contain a siliconized sodium bicarbonate base, the traditional
dry chemical. Cleanup after use is generally easy, because the chemical does
not normally bake to a hot metal surface. Non-toxic.
Operation: Squeeze the lever, which opens the valve, allowing the chemical to be forced out. Upright
squeeze grip operation approved to -65°F (-52°C).
Construction: Heavy-duty steel cylinder with rugged metal valve and siphon tube with replaceable
valve stem seal, visual pressure gauge pull pin and upright squeeze grip.
CLASS B,C Fires
MERCURY EXTINGUISHERS - HALOTRON AGENT
This model contains the clean extinguishing agent Halotron® 1, which is EPAapproved, government-accepted and specified. This agent discharges as a
liquid, then quickly evaporates, leaving no residue to clean up afterwards. U.S.
FAA-approved for use in airports. NFPA-10 rating. Electrically non-conductive.
Operation: Squeeze the lever, which opens the valve, allowing the chemical to be forced out. Temperature range from -40°F to +120°F.
Construction: Drawn steel cylinder with steel siphon tubes, power cone discharge stream, upright
squeeze grip visual pressure gauge and corrosion-resistant paint finish. Models 2-1/2 & 5 have aluminum valves, models
SENTINEL EXTINGUISHERS- CARBON DIOXIDE
This extinguisher contains liquid carbon dioxide under pressure.
SATURN EXTINGUISHERS - CLASS K WET CHEMICAL
These units are ideal for commercial restaurant applications as a portable
Operation: Squeeze the lever, which opens the valve, allowing the carbon dioxide to be forced supplement to pre-engineered suppression systems. A low “pH” potassium
out. The discharge, which changes into a gas and appears as a smothering cloud of white
acetate solution is discharged in a fine mist that provides excellent range
snow, is then directed to the fire through a funnel-shaped horn. Electrically non-conductive.
while preventing splashing and creating an effective saponification foam-type
Construction: Lightweight, high-pressure, aluminum cylinder with O-ring seal and straight
thread brass valve fits all sizes. The Sentinel is absolutely rust-free and up to 30% lighter than blanket necessary for suppressing liquid cooking media fires.
CO2 units with steel cylinders.
CLASS B,C Fires
272 - WATER MIST EXTINGUISHER
The water mist extinguisher is ideal for Class A fires where a potential
Class C (electrical) hazard exists. Units shipped empty.
Operation: The unique misting nozzle provides safety from electrical shock, making this extinguisher ideal for use in telecommunications and cleanroom environments.
Construction: Non-magnetic cylinder and misting nozzle. For use in medical facilities.
Class A,C Fires
Operation: Squeeze the lever, which opens the valve, allowing the chemical to be forced out.
Construction: Stainless steel cylinder with protective nozzle tip orifice seal and non-metallic nozzle
tip finger guard. Industry standard horn and nozzle design.
Name plate shows only the class “K” symbol.
CLASS K Fires
SUBMITTAL: FIRE EXTINGUISHERS
Qty
1
21
1
1
Nominal Capacity Shipping Weight Cylinder Diameter Overall Height Overall Width
Model
Shipping Volume
U/L Rating
Optional Mark Bracket
US CG Approved
Grenadier-P
2-1/2 gal.
7.75 lbs. «
7"
24-1/2"
9"
1.1 cu.ft.
2A
MB810
YES
Cosmic 2-1/2E*
2-1/2 lbs.
5 lbs.
6 lbs.
10 lbs.
20 lbs.
20 lbs.
50 lbs
5 lbs.
10 lbs.
15 lbs.
20 lbs.
2-1/2 lbs.
5 lbs.
5-1/2 lbs.
6 lbs.
10 lbs.
20 lbs.
50 lbs.
2-1/2 lbs
5 lbs
11 lbs
11 lbs
15-1/2 lbs
15-1/2 lbs
1.8 gal
2.5 gal
5.5 lbs.
10 lbs.
12.75 lbs.
18.25 lbs.
33.5 lbs.
38 lbs.
174 lbs
14 lbs.
28.25 lbs.
37.75 lbs.
50.75 lbs.
5/5 lbs.
9.25 lbs.
10.5 lbs.
13.75 lbs.
18.25 lbs.
38 lbs.
174 lbs.
5.25 lbs
9.5 lbs
21.25 lbs
22.5 lbs
25.75 lbs
27.5 lbs
22.5 lbs
33.5 lbs.
3-3/8"
4-1/4"
5"
5-1/8"
7-1/2"
7"
-5-1/4"
7"
7"
8"
3-3/8”
4-1/4"
4-1/4"
5"
5-1/8"
7-1/2"
-3-3/8"
4-1/4"
7”
6”
7"
6"
7"
7"
15-1/2”
16-3/8"
16"
21”
21-1/4”
24”
46”
17-3/4"
24"
30"
30"
15-1/2”
15-1/4"
16-3/8"
16-1/4"
21"
23-1/4”
46”
15-1/2"
16-3/8"
17-1/2”
21-7/8”
17-1/2"
21-7/8"
19-1/4"
24-1/2"
5-3/4”
7-1/4"
7-3/4"
7-3/4”
8-3/4”
10-1/4”
21-1/2”
8-1/4"
12"
12"
13"
5-3/4”
5-1/2"
7-1/4"
8-1/2"
7-3/4”
10-1/4”
21-1/2”
6-3/8”
7-1/4"
8-5/8”
9-1/4”
8-5/8”
9-1/4"
9"
9"
.2 cu.ft.
.35 cu.ft.
.5 cu.ft.
.65 cu.ft.
1.0 cu.ft.
1.0 cu.ft.
-.65 cu.ft.
1.3 cu.ft.
1.0 cu.ft.
2.1 cu.ft.
.2 cu.ft.
.35 cu.ft.
.4 cu.ft.
.5 cu.ft..
.65 cu.ft.
1.0 cu.ft.
-.25 cu.ft.
.3 cu.ft.
1.0 cu.ft.
1.0 cu.ft.
1.0 cu.ft.
1.0 cu.ft.
.9 cu.ft.
1.1 cu.ft.
1A-10BC
3A-40BC
3A-40BC
4A-80BC
10A-120BC
10A-120BC
20A-160BC
5BC
10BC
10BC
10BC
10BC
10BC
40BC
40BC
40BC or 60BC
120BC
160BC
2BC
5BC
1A-10BC
1A-10BC
2A-10BC
2A-10BC
Class K
Class K
MB817C or MB817A*
MB818C
MB808A
MB846C or MB846A
MB811C
MB810A
--MB809C or MB809A
MB810C or MB810A
MB810C or MB864A
MB811C or MB811A
MB817C or MB817A*
MB818A
MB818C or MB818A
MB808A
MB846C or MB846A
MB810C or MB810A
-MB817C or MB817A*
MB818C or MB818A
MB810C
MB812A
MB810C
MB812A
MB810C or MB810A
MB810C or MB810A
YES
YES
YES
YES
YES
YES
-YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
-N/A
YES
YES
YES
YES
YES
---
2.5 gal
8 lbs. «
7”
28”
14”
1.3 cu ft.
2AC
MB810NM
--
Cosmic 5E
Cosmic 6E
Cosmic 10E
Cosmic 20E (FE20C)
1 Cosmic 20E (FE20A)
495
1
1
1
1
1
1
1
1
1
1
PAGE 2 OF 2
Sentinel 5
Sentinel 10
Sentinel 15
Sentinel 20
Galaxy 2-1/2*
Galaxy 5
Galaxy 5-1/2
Galaxy 6
Galaxy 10
Galaxy 20
496
1 Mercury 2-1/2*
1 Mercury 5
1 Mercury 11 (FM11C)
Mercury 11 (FM11A)
1 Mercury 15-1/2 (FM15C)
Mercury 15-1/2 (FM15A)
1 Saturn 15
1 Saturn 25
1 272
* INDICATES MARK BRACKET STANDARD. J HOOK WALL BRACKET STANDARD WITH ALL OTHER EXTINGUISHERS.
«JL extinguishers are shipped fully charged with the exception of the Grenadier P & 272. Note: NFPA regulations also require extinguishers to be inspected when initially placed in service and all local fire code and
tagging requirements must be adhered to. All fire extinguisher sizes are nominal. Contact Customer Service For More Information About Ordering Tagged Extinguishers in Your Area.
Distributor:
Contractor:
Model #: Cosmic 5E
Project:
HEADQUARTERS:4450 WEST 78
TH
Quantity: 2
Approved By:
Architect:
Date:
ST CIRCLE, BLOOMINGTON, MN 55435-5416 PH: 800-554-6077 FAX: 952-835-2218 EMAIL: JL@JLINDUSTRIES.COM WWW.ACTIVARCPG.COM
ACPG SOUTHEAST (THOMAS ENTERPRISES): FT MYERS, FL ACPG WEST COAST (SAMSON): COMMERCE - CA, WAREHOUSES: PA, TX, GA, IL , WA,
6-72012
Architectural Series Fire Extinguisher Cabinets
Submittal and Detail Sheet
Zephyrhills Fire Station #2
PROJECT:_____________________________
AL 2409-R3
MODEL NUMBER:_______________________
Zephyrhills, FL
LOCATION:___________________________
2
QUANTITY:___________________________
ARCHITECT:___________________________
WE Supply Division 10, LLC
CONTRACTOR:_________________________
DATE:_______________________________
SPECIFICATIONS:
DISTRIBUTOR:_________________________
All recessed and semi-recessed cabinets and surface-mounted steel cabinets have a heavy gauge, white baked enamel box. Surface-mounted
cabinets with aluminum door and trim have a box constructed entirely of clear or color anodized aluminum. Surface-mounted cabinets with
stainless steel door and trim have a box constructed entirely of 304 stainless steel with a #4 finish.
Steel and stainless steel cabinets have a full ½" thick hollow metal heavy gauge door. Trims and doors feature one piece construction with satin
finish pull handle, continuous matching hinge, and self-adjusting roller catch. Baked white enamel finish is standard for steel units. Stainless
steel cabinets have a #4 finish, 304 stainless steel.
Aluminum cabinet doors and trims are extruded or fabricated aluminum with clear satin anodized finish. Aluminum door is ½" thick with satin
finish matching pull handle and hinge. Color anodized finishes are available as options.
STEP 1: Select cabinet model number from the dimensions on page 2 and indicate on the top of this sheet. To specify aluminum trim and door,
use the prefix, "AL" before the model number. To specify stainless steel trim and door, use the prefix, "SS" before the model number. Note:
Rough opening dimensions are larger for fire-rated cabinets. Please refer to separate Fire-Rated Cabinet Submittal and Detail Sheet.
◆
◆
† Trimless cabinets must be installed before the drywall because their plaster stops must be behind the drywall.
Trimless cabinets are not recommended for block wall installation.
* See back of this sheet or attached sheet for Recessed Handle (required only for 4" return trims when ADA wall projection compliance is
necessary)
LARSEN'S MANUFACTURING COMPANY - www.larsensmfg.com
7421 Commerce Lane N.E., Minneapolis, MN 55432 Phone: (763) 571-1181 FAX: (763) 571-6900
FLORIDA DIVISION: 3130 N.W. 17th Street, Ft. Lauderdale, FL 33311 Phone: (954) 486-3325 FAX: (954) 486-3352
©2007 Larsen's Mfg. Co.
CABINET DIMENSIONS - ARCHITECTURAL SERIES
Model
Number
◆
Trim Style and
Projection
Inside Box Dimensions
Outside Trim
Dimensions**
Recommended
Extinguisher
Rough Opening***
Height
Width
Depth
Height
Width
Height
Width
Depth
Capacity
__ 2409-R1
__ 2409-5R
__ 2409-R3
Rec. 5/16"
Semi-Rec. 1½"
Semi-Rec. 2½"
24"
24"
24"
9½"
9½"
9½"
5"*
5"*
5"*
27½"
27½"
27½"
13"
13"
13"
25"
25"
25"
10½"
10½"
10½"
5¼"
4"
3"
MP 2½,
MP5,MP5-A,
DC2½,DC5,
HT2½”HT5
__ 2409-R2
__ 2409-R7
__ 2409-6R
__ 2409-R4
__ 2409-RM
__ 2409-RT
__ 2409-SM
__ 2409-RA
Rec. 5/16"
Semi-Rec. 1½"
Semi-Rec. 2½"
Semi-Rec. 3½"
Semi-Rec. 4½"
Trimless
Surface Mounted
Semi-Rec. 4"
24"
24"
24"
24"
24"
24"
27½"
24"
9½"
9½"
9½"
9½
9½"
9½"
13"
9½"
6"
6"
6"
6"
6"
6"
6"
6"
27½"
27½"
27½"
27½"
27½"
27½"
27½"
13"
13"
13"
13"
13"
13"
13"
25"
25"
25"
25"
25"
†
25"
10½"
10½"
10½"
10½"
10½"
†
10½"
6¼"
5”
4"
3”
2"
6½"
2½"
MP 2½,MP5,
MP5-A,
DC2½,DC5
MP6,MP10
DC6,DC10,CD5
HT2½”, HT5
* Depth is 4¾" when supplied with aluminum door and trim. The AL2409-5R has a 1¼" square trim.
__ 2712-R
__ 2712-RK
__ 2712-RL
__ 2712-RM
__ 2712-RT
__ 2712-SM
__ 2712-RA
Rec. 5/16"
Semi-Rec. 1¼"
Semi-Rec. 2½"
Semi-Rec. 4½"
Trimless
Surface Mounted
Semi-Rec. 4"
27"
27"
27"
27"
27"
30½"
27"
12"
12"
12"
12"
12"
15½"
12"
8"
8"
8"
8"
8"
8½"
8"
30½"
30½"
30½"
30½"
30½"
30½"
15½"
15½"
15½"
15½"
†
15½"
15½"
28"
28"
28"
28"
†
28"
13"
13"
13"
13"
†
13"
8¼"
7¼"
6"
4"
8½"
4½"
All of Above,
PW 2½”,MP20,
DC20,CD10
WC-6L
HT11, HT15½”
__ 2720-R
__ 2720-RK
__ 2720-RL
__ 2720-RM
__ 2720-RT
__ 2720-SM
__ 2720-RA
Rec. 5/16"
Semi-Rec. 1¼"
Semi-Rec. 2½"
Semi-Rec. 4½"
Trimless
Surface Mounted
Semi-Rec. 4"
27"
27"
27"
27"
27"
30½"
27"
20"
20"
20"
20"
20"
23½"
20"
8"
8"
8"
8"
8"
8½"
8"
30½"
30½"
30½"
30½"
30½"
30½"
23½"
23½"
23½"
23½"
23½"
23½"
28"
28"
28"
28"
†
28"
21"
21"
21"
21"
†
21"
8¼"
7¼"
6"
4"
8½"
4½"
Two Each of
The listed:
PW2½”,MP10,
DC10,MP20,
DC20,CD5, D10
WC-6L,HT11, HT15½”
__ 3012-R
__ 3012-RK
__ 3012-RL
__ 3012-RM
__ 3012-RT
__ 3012-SM
__ 3012-RA
Rec. 5/16"
Semi-Rec. 1¼"
Semi-Rec. 2½"
Semi-Rec. 4½"
Trimless
Surface Mounted
Semi-Rec. 4"
30"
30"
30"
30"
30"
33½"
30"
12"
12"
12"
12"
12"
15½"
12"
8"
8"
8"
8"
8"
8½"
8"
33½"
33½"
33½"
33½"
33½"
33½"
15½"
15½"
15½"
15½"
15½"
15½"
31"
31"
31"
31"
†
31"
13"
13"
13"
13"
†
13"
8¼"
7¼"
6"
4"
8½"
4½"
Same as
2712
__ 3612-R
__ 3612-RK
__ 3612-RL
__ 3612-RM
__ 3612-RT
__ 3612-SM
__ 3612-RA
Rec. 5/16"
Semi-Rec. 1¼"
Semi-Rec. 2½"
Semi-Rec. 4½"
Trimless
Surface Mounted
Semi-Rec. 4"
36"
36"
36"
36"
36"
39½"
36"
12"
12"
12"
12"
12"
15½"
12"
8"
8"
8"
8"
8"
8½"
8"
39½"
39½"
39½"
39½"
39½"
39½"
15½"
15½"
15½"
15½"
15½"
15½"
37"
37"
37"
37"
†
37"
13"
13"
13"
13"
†
13"
8¼"
7¼"
6"
4"
8½"
4½"
__ M3216-R
__ M3216-RK
__ M3216-RL
__ M3216-RM
__ M3216-RT
__ M3216-SM
__ M3216-RA
Rec. 5/16"
Semi-Rec. 1¼"
Semi-Rec. 2½"
Semi-Rec. 4½"
Trimless
Surface Mounted
Semi-Rec. 4"
32"
32"
32"
32"
32"
35½"
32"
16"
16"
16"
16"
16"
19½"
16"
8"
8"
8"
8"
8"
8½"
8"
35½"
35½"
35½"
35½"
35½"
35½"
19½"
19½"
19½"
19½"
19½"
19½"
33"
33"
33"
33"
†
33"
17"
17"
17"
17"
†
17"
8¼"
7¼"
6"
4"
8½"
4½"
Same as 2712
FB 3612 OPTION:
w/Shelf &
Fire Blanket
PW2½”,MP20,
DC20,CD10,
CD15,
WM2½”
† Trimless cabinets must be installed before the drywall because their plaster stops must be behind the drywall.
Trimless cabinets are not recommended for block wall installation
** Deduct ¾" from HxW dimensions for cabinets with aluminum trim.
*** Rough openings are larger for fire-rated cabinets. Please refer to Fire-rated Extinguisher Cabinet Submittal and Detail Sheet.
NOTE: Semi-recessed and surface-mounted cabinet compliance with ADA wall projection guidelines depends on several location and installation issues.
Please refer to http://www.larsensmfg.com/
OPTIONAL "FIRE" HANDLE
OPTIONAL RECESSED HANDLE
Optional recessed handle is available at
additional cost for Solid, H-Duo or V-Duo
Doors. Larsen-Loc® is also available with
recessed handle. The recessed handle
must be specified with 4" projecting trims in
order for the cabinet to comply with ADA
wall projection guidelines.
Standard
Red
Black
White
LARSEN'S MANUFACTURING COMPANY - www.larsensmfg.com
7421 Commerce Lane N.E., Mpls, MN 55432 Phone: (763) 571-1181 FAX: (763) 571-6900
th
FLORIDA DIVISION: 3130 N.W. 17 Street, Ft. Lauderdale, FL 33311 Phone: (954) 486-3325 FAX: (954) 486-3352
©2007 Larsen's Mfg. Co.
1 each
6” x 9” ADA Men’s Restroom Sign
(Black Background / White lettering)
1 each
6” x 9” ADA Women’s Restroom Sign
(Black Background / White lettering)