SC9 Safe Area Sample Controller remote location. During the sampling process the operator can view live flow information and any alarms are displayed on the LCD screen. The SC9 has two levels of security (controlled by a remote switch) and has error codes to aid diagnosis in the unlikely event of a fault. In the event of power failure all set-up and batch/sample totals are retained by the SC9 in non-volatile Ram. The SC9 is a flow proportional sample controller designed for use with in-line (insertion probe based) systems. The sample probe is actuated by a flow proportional ‘grab’ control signal generated by the SC9 ensuring that the batch sample is representative of the whole batch. The Jiskoot SC9 controller uses a flow meter input in conjunction with the batch volume entered by the operator and desired sample volume to determine the sample actuation frequency. The SC9 can also be used to drive ‘open-loop’ flow proportional injection pumps The SC9 can be configured to control and monitor in-line sampling systems with one or two sample receivers. In systems with two receivers the controller will automatically select the second receiver once the first one is full. The Jiskoot SC9 also incorporates an auto-stop feature to prevent over-filling of sample receivers. The SC9 is easy to use; the operator simply enters the batch volume and presses the run button. The controller will perform all the necessary calculations to determine sampling parameters and achieve the correct sample volume for analysis. Sampling of the batch can be stopped at any time either from the front panel or via a remote stop button. The SC9 has a large easy to read six-digit LCD display and is controlled using four buttons on the front panel which can also be wired to a Features • Low cost controller for sampling applications • Large, easy to view display • Simple to operate • Remote Start/Stop • Can be configured for use with sampling systems containing one or two sample receivers • Automatic sample receiver change-over • Emergency stop when receivers are full to prevent over-filling • Batch auto over-run facility – allows small errors in batch volume entry • Sampling in compliance with API 8.2 (If compliance with ISO 3171 and IP 6.2 are required then a controller with performance monitoring, such as the Jiskoot InSight, is needed.) Data Sheet S114-0405-2 • SC9 Safe Area Sample Controller Introduction The SC9 is a low cost safe area controller designed for the control and monitoring of a flow proportional in-line sampling system in accordance with the API 8.2 sampling standards. Typical applications are pipeline and terminal duty for tanker loading/ discharge and other custody transfer applications for liquid and gaseous hydrocarbons. Specification Operator Interface Display 6 Digit 0.7” (17.8mm) high Liquid Crystal Display Data Entry 4 Push Buttons Data Retention All set-up and totalisers are held in non-volatile memory with 10 years minimum data retention Utilities Power Supply (AC or DC) AC DC Power Consumption Nominal 5 Watts 95 - 135V AC or 190 - 260V AC 50/60 Hz (Set internally) 11.5 - 28.5V DC Inputs Analogue (Flow) – Optional Extra Input Range Input Impedance Isolated 4-20mA, 0-20mA or 0-10V DC Current : 10 ohms + PTC 10 ohms Voltage : 5x106 Pulse (Flow) Input Range Scaling Range Input Types 0 to 10 kHz (Min. 0.25 Hz for rate) 0.1 to 50,000 Voltage free contact, Open Collector or TTL Logic Digital Remote Run, Display, Batch Set & Stop/Reset Outputs Transducer Supply 8 to 24V DC (50mA max.) – Field adjustable Grab Output Relay Max. No. Of Grabs Max. Grab Rate 10 to 50,000 60 grabs per minute Receiver Change Relay Relay Specification Max. Switched Voltage 250V AC or 30V DC Max. Switched Current 5 Amps – Resistive or 1.5 Amps Inductive Max. Switched Power 1250VA Approvals Electrical Approvals ETL (US) approved to UL 508 & CSA CE Compliance Enclosures Safe Area Type Dimensions Panel Cut Out Weight Hazardous Area See data sheet SC9EX IP 65 or NEMA 4x 144 x 72 x 179mm (W x H x D) over connectors 139 x 67mm (Tolerance +0.6mm) 1.3kg Environment Operating Temperature 0°C to 55°C Humidity Max. 95% Non-Condensing UK Jiskoot Quality Systems USA Jiskoot Quality Systems Cameron Measurement Systems Tel: +44 (0)1892 518000 Tel: +1 281 583 0583 Tel: +1 281 582 9500 Fax: +44 (0)1892 518100 Fax: +1 281 583 0587 Fax: +1 281 582 9599 Email: ms-jiskootuksales@c-a-m.com Email: ms-jiskootusasales@c-a-m.com Email: ms-marketing@c-a-m.com Jiskoot Quality Systems A Cameron Company www.jiskoot.com www.c-a-m.com/flo