Download Report

®
ELTHERM TT 6
USER-FRIENDLY PROGRAMMABLE THERMOSTAT
USER'S GUIDE
ELECTRICAL CONNECTION
Examples;
Electrical connection of the motorized ball valve EMV .. 110 series or
16A/250VAC, cosϕ=1
regulating motor MV 120 / ...
®
10A/250VAC, cosϕ=0.6
Room thermostat
TT6
MV 120/...
EMV 110..
1 2 3
24...240V
50Hz
black CLOSE
grey OPEN
blue
Electrical connection of the burner or circulation pump
16A/250VAC, cosϕ=1
10A/250VAC, cosϕ=0.6
Room thermostat
TT6
USER'S GUIDE
Choosing location for INSTALLATION
For obtaining thermostat's best performance upon using,
recommend user to follow up with precaution listed below.
(1). Place thermostat on wall inside the room approximate 1.5
meter above floor.
(2). Avoid position where temperature sensing easily
interfered by ambience, such as, directly exposed to
Sun-Light, too near to any Heat-Generate devices
/refrigerator, right next to entrance/exit/window, etc.
(3). Prevent thermostat from installed at position that
furniture may interfere air-flow, stagnant air-flow location
is not suitable for installing thermostat.
(4). Keep thermostat away from high humid ambience, high
humidity is hazardous to thermostat's operational
duration.
(5). It's crucial, before installing thermostat, make sure house
renovation is finished, no tacky painting/plaster is right
on thermostat's installing position.
(6). To level thermostat prior to installation is not necessary.
(7). Push excess cable wires back into the wall while
positioning thermostat. If there is a draft, pack the
opening with non-combustible material.
(8). Place batteries in thermostat requiring batteries,
observing “+ ” and “ - ” positions.
črpalka
1 2 3
N
L
24...240V
50Hz
Electrical connection of electric radiators and other heating appliances
Room
thermostat
TT6
1
2 3
Max. load:
* Resistive load
16A/250VAC, cosφ=1
max. 3 kW
* Inductive load
10A/250VAC, cosφ=0.6
max. 2 kVA
heating appliance
Connection for electric boilers
TERMOMONT:
ETK-SET, ETK SET U, ETK SET for pipe systems
START INSTALLATION
Room thermostat
TT6
1
2 3
Boiler ETK-SET
(1). How to open top housing
Connection for electric boilers
TERMOMONT:
ETK - SET ELEKTRONIK
Room thermostat
TT6
1 2 3
4
Boiler ETK-SET ELEKTRONIK
C. WIRING GUIDE
Follow the el. scheme which is printed on the terminal's
cover.
Connection for boilers using solid
fuel, oil TERMOMONT:
Room thermostat
TKK, TKK3, TKU3, TŽK, TEMY,
TT6
CTK, BTK
pump
burner
room
thermostat
FIRŠT-ROTOTEHNIKA, s.p., Radegunda 54, SI-3330 Mozirje, Slovenija
tel. +386 3 898 35 00, fax. +386 3 898 35 35, e-mail: info@first.si, http://www.first.si
1
2 3
power
supply
cx4-2210-Eltherm-TT6-v7-eng.cdr
MON
RUN
TUE
SUN
WED
SAT
THU
FRI
TO ADJUST CLOCK
1. Rotary switch pointed to “RUN”.
2. Press
SAT, SUN
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
to enter clock adjusting.
+
3. Press
-
or
to select the day of week.
C. HOLD (Permanent override)
(MON- monday, TUE- tuesday, WED- wednesday, THUthursday, FRI- friday, SAT-saturday, SUN-sunday)
4. Press
again to enter adjusting hour of day.
+ or -
5. Press
to adjust.
6. Repeat procedure of pressing
finish adjusting minute of hour.
and
+/ -
to
1.Rotary switch pointed to RUN.
MON
RUN
2.Press HOLD to enter this permanent
override mode, LCD shall display “Temp
Set” “Hold”.
TUE
SUN
WED
SAT
3.Press
setting.
+
or
-
FRI
THU
PROG.SET
to adjust temperature
7. LCD display shall automatically return to main page 5
seconds after clock adjusting completed.
4.LCD display shall be flashing for approximate 8 second after temperature
setting finished, and skip to indicate ambient temperature after flashing
stopped. Thermostat starts to execute Permanent-Override function.
A. START TO PROGRAM
5. Press again HOLD , can release this “HOLD” command;
thermostat shall resume its original setting.
-To adjust
and
Temperature setting.
1.Rotary switch pointed to RUN.
2.Press
to enter
temperature setpoint.
+
3.Press
-
or
4.Press
5.Press
+
-
or
RUN
TUE
SUN
WED
SAT
FRI
THU
to adjust temperature.
to enter
MON
+
to adjust temperature.
This thermostat commands heating-system to operate with two
temperatures setting only, each of 7-day is spread into 48
independent time-scale, users can select length of time by own
preference, to coordinate with and temperature setting, for
coziest room temperature.
To set and temperature setting for each
independent time-scale.
1.Spin indicator on rotary switch to the desired day of weekand start
MON
RUN
setting. (Wednesday chosen for graphic
example)
1
2
3
4
5
6
7
RUN
2. Press
or
indicate current
3. Press again
-
+
LCD display shall
or
temperature setting.
TUE
SUN
WED
SAT
or
-
THU
FRI
to change setting.
4. LCD display shall be flashing for approximate 8 second after temperature
setting finished, and skip to main page of LCD-display after flashing stopped.
Thermostat starts to execute “MANUAL” function.
setting this MANUAL function at the section of
, thermostat shall
※When
maintain executing “MANUAL” until program runs to the section of
.
Vice versus. On LCD-display main page, when MANUAL in executing,
or
shall disappear from display at the section of time that
**MANUAL.** function is executing.
5. Spin switch away from “RUN” and spin it back to “RUN” can terminate this
“MANUAL” function.
TUE
SUN
WED
SAT
MON
RUN
MON
RUN
THU
FRI
TUE
SUN
TUE
SUN
WED
SAT
WED
SAT
FRI
THU
2. LCD display shall show
0
MON
1. Rotary switch pointed to RUN.
temperature setpoint.
(MON- ponedeljek, TUE- torek,
WED- sreda, THU- četrtek, FRI- petek,
SAT-sobota, SUN-nedelja)
(Temporary Override)
PROG.SET
6.Wait 5 seconds after temperature adjustment finished, thermostat
shall memorize setting and return to main page.
※
MANUAL
8
9
10
THU
11
FRI
PROG.SET
PROG.SET
LOW BATTERY INDICATION
0
4
5
6
7
8
9
10
11
16
17
18
19
20
21
22
23
4
5
6
7
8
9
10
11
16
17
18
19
20
21
22
23
If on the screen appears "Lo"
is necessary to replace 2 batteries!
12
13
14
3.Press
and
15
16
or
17
18
19
20
21
22
23
We recommend using alkaline
battery LR06 1,5V.
to alter setting between
14
on LCD display.
+
-
4.Press
or
to select each individual time-scale, LCD
display shall also indicate each time-scale by digital number and
flashing, to guide users.
5. After finished setting all 7-day of week, spin rotary switch back to
“RUN”. Thermostat starts to operate its program.
MON ~ FRI
Factory preset 0 1 2 3 4 5 6 7 8 9 10 11
(default value)
※
HEATING INDICATION
0
Symbol
indicates pump, burner, el.
heater operation.
14
= 21°C
=16°C
12
13
14
15
16
17
18
19
20
21
22
23
FIRŠT-ROTOTEHNIKA, s.p., Radegunda 54, SI-3330 Mozirje, Slovenija
tel. +386 3 898 35 00, fax. +386 3 898 35 35, e-mail: info@first.si, http://www.first.si