1. travel
2. specialty travel
3. ecotourism

Owner’s Manual:
05025 Red D Mix
1786755 Rev A
ECO 13-0002 J
April 2014
Five-Gallon Gyro Mixer—Non-Explosion Proof
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
Table of Contents
Safety Information 3
Safety Precaution Labels 4
Safety Precaution Summary 5
Exploded Views 14
BASE 14
CLAMP GUIDE 15
CRANK HANDLE 16
Introduction 6
Application 6
Specifications 6
Installation 7
DIGITAL TIMER 17
DOUBLE ROW BEARING 18
MAIN DRIVE 19
FRAME AND DRIVE 20
Prepare for Use 7
ROTATING FRAME ASSEMBLY, LOWER
21
SECTION Operation 9
ROTATING FRAME ASSEMBLY, UPPER
22
SECTION Control Panel 9
Install a Pail 10
Care and Maintenance 11
SHROUD 23
Ordering 24
Cleaning 11
Maintenance Schedule 11
Optional Parts 24
Replacement Parts 24
Ordering Information 24
Troubleshooting 12
Warranty 25
Wiring Diagram 13
Notes 26
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
2
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
Safety Information
Review this owner’s manual and read all warning labels on the machine prior to use.
The three main safety notifications used in this manual and on the warning labels are WARNING, CAUTION
and NOTICE. They have specific meanings and indicate the potential dangers from misuse of the machine.
“WARNING!” indicates a hazardous situation, which, if not avoided,
could result in death or serious injury. These serious injuries could
include permanent loss of function or significant disfigurement, disability,
considerable pain and suffering, amputations, severe burns, and loss or
impairment of vision or hearing. Take all necessary precautions to avoid
unnecessary injury.
“CAUTION!” indicates a hazardous situation, which, if not avoided, could
result in minor or moderate injury.
NOTICE
“NOTICE” indicates practices that do not involve physical injury but may
damage the machine.
Safety Information, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
3
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Safety Information, continued
Safety Precaution Labels
NOTICE
BEFORE RUNNING MACHINE, DID YOU...
1. POSITION CONTAINER PROPERLY?
2. ATTACH THE BAIL SPRING?
3. TIGHTEN CLAMP SECURELY?
WEEKLY
CLAMP RELEASE
LEVER
LUBRICATE SHAFT WITH 3 IN 1 OIL
WEEKLY
THRUST BEARING
TURN ROTATING ASSEMBLY UPSIDE DOWN
AND LUBRICATE ALL AROUND OUTSIDE EDGE
OF THRUST BEARING WITH 3 IN 1 OIL.
WEEKLY
BOTTOM PLATE
CLEAN OFF PAINT WITH HOT SOAPY
WATER.
EVERY 6
MONTHS
CLAMPING SCREW
GREASE WITH STANDARD MULTI-PURPOSE
LITHIUM BASED GREASE AS NEEDED.
EVERY 6
MONTHS
GREASE ZERKS
GREASE WITH STANDARD MULTI-PURPOSE
LITHIUM BASED GREASE. TWO SQUIRTS PER
ZERK ONLY. OVER GREASING WILL CAUSE
PREMATURE FAILURE OF BEARING.
AS NEEDED
VERTICAL SLIDE
TUBES
CLEAN OFF DIRT AND PAINT WITH
HOT SOAPY WATER.
Safety Information, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
4
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Safety Information, continued
Safety Precaution Summary
Avoid dangerous environments. Do not use
the machine in a damp or wet environment. Keep
the work area well lit.
Machine must be properly grounded before
use; Improper grounding could cause electric
shock and injury.
Disconnect power cord before servicing,
cleaning, or removing any covers, and follow
lockout/tagout procedures in owner's manuual;
failure to disconnect power could cause electric
shock and injury.
Review owner's manual before installing or
operating.
Keep the work area clean. Cluttered areas and
benches invite accidents. To prevent accidents, be
sure all electrical cords are out of the way.
Operation
Keep Customers away. All customers should
be kept away from the work area. The machine
should be used only by properly trained individuals.
Clamp the can carefully to ensure that it is
held securely during the mixing cycle.
Do not operate without a can installed.
Maintenance
Always follow these safety precautions when
operating the Red Devil Equipment Co. 05025
Gyro Mixer:
Before operating the machine, read this
Owner's manual carefully. Learn the machine’s
applications and limitations.
Ground the machine properly. Be sure to
follow proper grounding and electrical procedures.
Avoid extension cords. To minimize the risk of
tripping the circuit breaker, improper electrical
grounding, or over-loading, extension cords are
not recommended.
Disconnect power to machine. When cleaning
the machine or doing maintenance work, always
disconnect machine from power source.
Keep the machine clean. Clean all surfaces
with a mixture of lukewarm water and mild
detergent. Avoid solvent based cleaners or
thinners.
To avoid electric shock, don’t get the timer,
control panel, or wiring wet.
Service properly. Follow the maintenance
procedures outlined in this manual. If problems
occur, contact Red Devil Equipment Co.
Use the proper power source. Refer to the
machine data plate on the right side panel. If the
machine data plate has been removed or is
unreadable, call the Red Devil Equipment Co.
Customer Service Department (see the back cover
of this owner’s manual) before connecting the
machine to a power source.
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
5
1786755 Rev A
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
ECO 13-0002 J
April 2014
Introduction
Application
Specifications
Congratulations on your purchase of the 05025
Gyro Mixer. This machine is designed to
accommodate standard five-gallon plastic or metal
pails weighing up to 125 lb. (45.3 kg).
Unit Size: W 32.5 in. (82.5 cm) D 34 in. (86.4 cm)
H 46.5 in. (118 cm)
Understand your machine's features and proper
operation to take full advantage of its capabilities.
Weight: 440 lb.
Electric Service: 110 V 60 Hz
Capacity: 125 lb. (45.3 kg)
Read this entire manual completely before
operating the machine, . Practice installing and
removing a pail before mixing for the first time.
Sizes Mixed: 5 gal. (19 L), 13 in. (33 cm) to 16 in.
(41 cm) H
An optional Riser Leg Kit is available for additional
height adjustments. Please see the Ordering
section for additional information.
Timer: Digital Display Timer
Load Height: 13 in. (33 cm)
Keep this manual for future reference.
Always follow all safety instructions!



www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
6
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
Installation
Prepare for Use
110 V UNITS
Machines rated at 110 V, 60 Hz are for use on a
nominal 120 V circuit.
Machine must be properly grounded before
use; Improper grounding could cause electric
shock and injury.
Disconnect power cord before servicing,
cleaning, or removing any covers, and follow
lockout/tagout procedures in owner's manuual;
failure to disconnect power could cause electric
shock and injury.
Review owner's manual before installing or
operating.
EXTENSION CORDS
Avoid using extension cords. If an extension cord
is unavoidable, consult a qualified electrician
to determine what type of extension cord will
satisfy the grounding, current capacity, and other
requirements of the particular situation.
IMPORTANT: Before attempting to operate the
machine:
1. Remove all packing material.
2. Position the machine on a firm, level
surface.
ELECTRICAL
CONNECTION AND GROUNDING
REQUIREMENTS
The machine MUST BE GROUNDED. If there
should be an electrical short circuit, grounding
reduces the risk of electric shock by providing an
escape wire for the electric current.
The machine’s power cord has a grounding
wire with an appropriate grounding plug. This plug
must be inserted into an electrical outlet that is
properly installed and grounded according to all
local codes and ordinances.
3. Follow the electrical connection instructions
described above.
4. Verify that the machine is level:
a. Clamp a 5 gallon pail in the machine.
b. Turn the machine on.
c. Try to slide a sheet of paper underneath
each of the four feet.
Installation, continued...
If you must repair or replace the power cord
or plug, do not connect the grounding wire to
either flat-blade terminal. The wire with insulation
having an outer surface that is green (with or
without yellow stripes) is the grounding wire.
Check with a qualified electrician if you don’t
completely understand these grounding
instructions, or if you are not sure whether the
machine is properly grounded. Do not modify the
plug provided; if it won’t fit in the outlet, have a
proper outlet installed by a qualified electrician.
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
7
1786755 Rev A
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
ECO 13-0002 J
April 2014
...Installation, continued
d. Adjust (lower) any feet under which the
paper can fit.
i. Clamp the hex riser (A) with a 1 ⅜
wrench.
ii. Loosen the locking nuts (B) about two
turns using a ¾ in. wrench.
iii. Turn the head of the foot (C) clockwise
to lower the foot until it is in full contact with
the floor.
iv. Try to slide a sheet of paper underneath
the adjusted foot to recheck the foot
adjustment while the machine is running.
v. Tighten the locking nuts (B) if the foot is
in full contact with the floor.
vi. Repeat with any additional feet that may
still need adjustment.
(A)
(C)
(B)
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
8
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
Operation
Control Panel
• E-Stop Push-Button (A): Only use to
immediately cut the power to the machine.
• Breaker Switch, 20-Amp (B): Turn off the
power and push the switch if the breaker trips.
• Digital Display (C): View programming
revision, cycle count, and cycle time remaining.
• Two-Minute Cycle (D): Push to set a twominute cycle, and to increase a cycle in two minute
increments.
• Three-Minute Cycle (E): Push to set a threeminute cycle, and to increase a cycle in three
minute increments.
• Stop (F): Push to stop the cycle. Any remaining
cycle time will be deleted.
(A)
(B)
(C)
(D)
(E)
(F)
Operation, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
9
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Operation, continued
Install a Pail
MIXING PROCEDURE TO INSTALL A PAINT
PAIL:
1. Open the machine door.
Pull the red ratchet lever (A) toward you
and turn the handle on the top of clamp (B)
counterclockwise to raise the plate.
2. Slide the pail under the clamping (top) plate (C).
3. Position the pail in the grooves on the bottom
plate (D). The grooves on the plate keep the pail in
place during mixing.
4. Lower the clamping plate (B) by turning the
handle clockwise. Once the plate makes contact
with the pail, tighten another 1/4 turn.
5. Secure the bail of the pail with the bail spring.
6. Close the door and start the machine.
NOTICE A safety interlock prevents machine
operation if the door is open.
NOTICE
If the bail spring wasn’t properly
secured, press the EMERGENCY STOP button on
the control panel.
(B)
(A)
MOVING PARTS INSIDE
Do not open the door until the machine comes to
a complete stop; moving parts inside could cause
serious injury.
TO REMOVE THE PAINT PAIL:
1. Raise the clamp all the way to the top by
holding the ratchet lever open while turning the
crank handle counter-clockwise.
2. Unfasten the bail spring.
3. Remove the pail:
Metal Pails: Grab pail handle and pull forward,
allowing the base of the pail to leverage itself off
of the strike plate near the roller. Pull the handle to
remove the pail from machine.
lastic Pails: Lift the pail by the lip with both hands
P
and pull it toward you, being careful to keep the
bottom from catching on the strike plate.
(D)
(C)
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
10
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
Care and Maintenance
Cleaning
Maintenance Schedule
Always unplug the power cord before
cleaning!
Always unplug the power cord before
performing maintenance tasks!
CLEANING:
Keeping the machine clean is important for reliable
operation. Colorant or base paint spilled on
machine surfaces can be removed using lukewarm
water and mild detergent for water-based/glycol
colorants. To preserve the appearance of the
machine, do not use abrasives to clean machine
surfaces.
LUBRICATION:
Speed Reducer
Maintenance not required. If oil change is
necessary due to debris build-up:
1. Remove oil drain plug on bottom side of
machine and drain oil from gearbox.
2. Remove the oil level plug and fill only up to that
level: with Mobil SHC 634 Synthetic oil.Do not
overfill or underfill.
Clamp
Lubricate the clamping screw threads and thrust
bearing as needed with 3-in-1 oil.
Ratchet Lever
Lubricate the shaft as needed with 3-in-1 oil.
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
11
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
Troubleshooting
PROBLEM
Machine won’t operate
CAUSE
REMEDY
Not connected to power source
Connect to power source
Building circuit breaker or fuse
blown
Reset breaker or replace fuse
Machine door does not make con- Readjust switch to make contact with limit
tact with limit switch
switch screw when door is closed
Motor thermal protector activated
Allow to cool, then restart
Machine circuit breaker tripped
Reset by pressing circuit breaker back in
Emergency E-STOP pushbutton is
activated
Turn switch knob 1/4-turn clockwise to
Pail won’t fit properly into
clamping plates
Pail damaged
Fix or replace pail
Machine doesn’t shut off at
end of mixing cycle
Faulty timer
Contact Red Devil Equipment Co.
Customer Service
Machine doesn’t shut off
when door is opened
Faulty door limit switch
Contact Red Devil Equipment Co.
Customer Service
Increasing mechanical noise
Bearings worn or damaged
Contact Red Devil Equipment Co.
Customer Service
Top clamp pad worn
Replace pad
Top clamp not secure
Turn the crank handle down until top plate
is snug on pail
Pail rotates inside the clamping plates
disengage
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
12
ECO 13-0002 J
1786755 Rev A
April 2014
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
Wiring Diagram
BLACK/WHITE
T1
NEUTRAL
T2
DIGITAL DISPLAY TIMER,
HORIZONTAL DISPLAY
5786234
BLACK/WHITE
BLACK WIRE
5782556
BREAKER, 20 AMP
5785315
BROWN WIRE
2X 5784935
HARNESS, OPERATIONS,
DIGITAL DISPLAY - 5025
5786416, SHOWN IN BOLD
RED
RED
BLUE
WHITE
WIRE
5782561
WIRE NUT,
YELLOW
9780543
EMERGENCY
STOP BUTTON
5784827
CONTROL AREA - TOP OF MACHINE
6
4
2
0
8
1
RELAY
5786331
WHITE
BLACK WIRE
5782557
BLACK
SHRINK
WRAP
WIRE NUT,
YELLOW
9780543
YELLOW
BLACK/WHITE
SHRINK WRAP
POWER CORD
5784034
MOTOR
HARNESS
5784036
WIRE NUT, ORANGE
9780542
SHRINK WRAP
RED
WHITE
GREEN
MOTOR-JUNCTION
BOX HARNESS
5784035
JUNCTION BOX
WIRE NUT,
ORANGE
9780542
SHRINK WRAP
DOOR SWITCH
5783815
BLUE
ORANGE
RED
BLACK
WHITE
YELLOW
GROUND
MOTOR
5785931
GROUND - GREEN
NEUTRAL/L1 - BLUE
HOT/L2 - BROWN
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
13
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
Exploded Views
Base
6
4
1
5
3
2
1
2
3
4
5
6
PART NO.
9786765
9785722
9785721
9785862
9781711
6786688
DESCRIPTION
Riser
Leveling Foot
Glider Foot
Hex Screw, 1/2-13 x .75
Nut, 1/2-13
Frame and Drive Assembly
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
14
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Exploded Views, continued
Clamp Guide
8
4
3
6
6
3
1
2
5
7
5
7
1
2
3
4
5
6
7
8
PART NO.
9783934
9786720
9783936
9786730
9786753
9782331
9780343
9784100
DESCRIPTION
Clamp Guide
Hub
Alignment Guide
Clamping Lead Screw
Vertical Guard
Flat Head Screw, 1/4-20 x 1.25
Nut, Nylock, 1/4-20
External Retaining Ring
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
15
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Exploded Views, continued
Crank Handle
8
7
5
6
5
3
9
4
1
2
1
2
3
4
5
PART NO.
9786706
9783950
9783365
9784628
9784629
DESCRIPTION
Handle, Crank
Rachet Gear
Button Head, 1/4-20 x .50
Crank Handle Wheel
Ball Bearing
6
7
8
9
9785283
9784633
9784632
9784729
Steel Bushing
Washer, Shim, 5/16
Buttonhead Screw, 1/4-20 x 1.75
Washer, Shim, 1/4
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
16
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Exploded Views, continued
Digital Timer
3
3
3
4
3
5
6
2
1
7
1
2
3
4
5
6
7
8
9
PART NO.
9786187
5785315
5784827
5786234
9783595
9786232
1786198
5784935
5782556
DESCRIPTION
Plate, Digital Timer
20 Amp Circuit Breaker
E-Stop Switch
Digital Timer
Nut, Nylock, #4-40
Spacer
Label, Digital Display
Jumper, E-stop
Wire, E-Switch to Power Switch
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
17
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Exploded Views, continued
Double Row Bearing
2
1
3
4
5
1
2
3
4
5
PART NO.
9783941
9783942
9783943
9783944
9784892
DESCRIPTION
Bearing Housing
17mm Double Row Ball Bearing
Washer, Thrust, 1.125 ID
Cage, Thrust Bearing, 1.125 ID
Washer, Thrust, Thick
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
18
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Exploded Views, continued
11
1
Main Drive
14
15
19
18
17
21
16
16
13
20
14
14
12
11
6
9
7
4
10
2
3
8
1
2
3
4
5
6
7
8
9
10
11
PART NO.
9785464
9786714
9786723
9786711
9786712
9786713
9785585
9782172
9783383
9688200
9780886
DESCRIPTION
Gearbox, Right Angle
Gearbox Mount
Shaft, Tumble
Helical Gear, RH, 76 Teeth
Flange Bearing, 1.50 ID
Brace
Square Key, .250 x 4.125
Hex Screw, 1/2-13 x 1.75
Nut, Nylock, 1/2-13
Washer,Flat, 1/2
Hex Screw, 3/8-x16 x 1.00
5
22
12
13
14
15
16
17
18
19
20
21
22
PART NO.
9781228
9780193
9100731
9561700
9780182
9785780
9781083
9785587
9784029
9780214
5785931
DESCRIPTION
Hex Screw 3/8 -16 x 1.25
Nut, Nylock, 3/8-16
Washer, Flat, 3/8
Hex Screw, 5/16-18 x 1.00
Nut, Nylock, 5/16-18
Hex Screw, 1/2-13 x 1.25
Flat Washer, .507 ID x 2.00 OD x .19
Flat Washer, .512 ID x 1.456 OD x .118
Hex Screw, 5/16-18 x 1.25
Lock Washer, 1/2
1 HP Motor, AC, 56C Frame
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
19
1786755 Rev A
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
ECO 13-0002 J
April 2014
...Exploded Views, continued
Frame and Drive
8
2
10
3
4
7
6
9
5
1
1
2
3
4
5
PART NO.
9786804
9782520
9786803
9780367
9780193
DESCRIPTION
Base Weldment
Roller
Roller Bracket
Isolator Set
Nut, Nylock, 3/8-16
6
7
8
9
10
PART NO.
9780182
9100023
9783894
9780368
9786768
DESCRIPTION
Nut, Nylock, 5/16-18
Washer, Flat, 5/16
Hex Screw, 3/8-16 x 2.50 Full Thread
Washer, Snub
Washer, Fender
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
20
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Exploded Views, continued
Rotating Frame Assembly, Lower Section
14
18
17
24
26
4
5
16
22
6
12
4
1
22
15
26
24
9
10
23
21
20
7
13
11
8
2
8
19
27
25
3
26
22
1
2
3
4
5
6
7
8
9
PART NO.
9786757
6786747
9786715
9785467
9786744
9786581
6786705
9786743
9786718
DESCRIPTION
Clamp Frame Weldment
Bottom Plate Assembly
Right Angle Gear Box, Tapered Shaft
25 mm Ball Bearing
Spacer 1.000 ID
Gear, Helical
Helical Gear Assembly
Gearbox Support Bracket
Gear Guard
10
11
12
13
14
15
16
17
18
PART NO.
9786731
9786725
9786384
9786728
9780221
9782154
9783383
9688200
9780214
DESCRIPTION
Spacer 1.0005 ID
Retaining Ring, 1.00 Shaft
Retaining Ring, 25mm Shaft
Washer, Shim
Hex Screw, 1/2-13 x 1.00
Hex Screw, 1/2-13 x 1.50
Nut, Nylock, 1/2-13
Washer,Flat, 1/2
Lock Washer, 1/2
19
20
21
22
23
24
25
26
27
PART NO.
9780193
9786469
9785481
9561700
9782407
9784441
9100023
9760521
9783365
DESCRIPTION
Nut, Nylock, 3/8-16
Flat Washer, 3/8 x 7/8
Key, Woodruff, No 806
Hex Screw, 5/16-18 x 1.00
Hex Screw, 5/16 x .75
Washer, Fender, 5/16
Washer, Flat, 5/16
Lock Washer, 5/16
Button Head, 1/4-20 x .50
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
21
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Exploded Views, continued
Rotating Frame Assembly, Upper Section
19
16
20
7
11
4
6
15
1
17
10
12
18
13
5
8
9
14
2
3
1
2
3
4
5
6
7
8
9
10
PART NO.
9786717
6786746
6786702
6786694
6783940
9783961
9784489
9783960
9784488
9784892
DESCRIPTION
Top Lead Screw Support
Clamp Guide Bar Assembly
Top Plate Assembly
Crank Handle Assembly
Bearing Assembly
Bronze Flange Bushing
Rachet Lever
Torsion Spring, LH
Spring Plate
Washer, Thrust, Thick
11
12
13
14
15
16
17
18
19
20
PART NO.
9786727
9783963
9783962
9783595
9783791
9783756
9654100
9780343
9780164
9781823
DESCRIPTION
Wave Washer, .44 ID x .75 OD
Shim Washer, .515 ID
Nut, Nylock, Thin, 1/2-20
Nut, Nylock, Thin, 3/8-16
Socket Head Screw, 1/4-20 x .50
Screw, Sockethead, 1/4-20 x 1.00
1/4 - 20 Nut
Nut, Nylock, 1/4-20
Washer, Split Lock, 1/4
Washer, Flat, 1/4
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, continued...
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
22
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
...Exploded Views, continued
Shroud
1
18
2
4
20
14
16
7
13
10
3
6
12
5
24
9
21
23
22
8
15
24
17
1
2
3
4
5
6
7
8
9
10
11
12
PART NO.
9786698
9786699
9786734
9786735
9786736
9785373
9783994
9785137
9786732
9783987
9786722
9785773
DESCRIPTION
Pannel, Top
Pannel, Back
Door
Pannel, Side, LH
Pannel, Side RH
Limit Switch Cover
Recess Bumper
Rubber Bumper
Bearing, Bronze
Door Handle
Door, Stop
Seal, Door
16
9
13
14
15
16
17
18
19
20
21
22
23
24
PART NO.
9785126
9783385
9783426
9781831
9785786
9785779
9780343
9760514
9100023
9783988
9760521
9780221
19
11
DESCRIPTION
Nut, Nylock, #8-32
Screw, Hex, Self-Threading, #10-32
Nut, Keps. #10-32
Hex Screw, 1/4-20 x 1.00 lg
Hex Screw, 1/4-20 x 1.50
Thread Cutting Hex Head 1/4-20 x .50
Nut, Nylock, 1/4-20
Washer, Flat, 1/4
Washer, Flat, 5/16
Hex Screw, 5/16-18 x .50
Lock Washer, 5/16
Hex Screw, 1/2-13 x 1.00
14
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
23
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
Ordering
Replacement Parts
HOW TO ORDER REPLACEMENT PARTS
Replacement parts can be ordered from Red Devil Equipment Co. by telephone, fax, or email:
RED DEVIL EQUIPMENT CO.
763-533-2969
800-221-1083
763-852-1811 (FAX)
orders@reddevilequipment.com
If you need help in determining the proper part(s) to order, please call customer service. at 1-800-221-1083.
Always indicate the Model and Serial numbers of the machine when ordering replacement parts.
GENERAL PARTS REPLACEMENT POLICIES
While your machine is under warranty, do not attempt on-site repair or parts replacement without first
contacting Red Devil Equipment Co. (to protect your warranty). After the warranty expires, replacement parts
and recommendations for on-site servicing are available from Red Devil Equipment Co. Please Customer
Service for assistance.
RESTOCKING FEE
A restocking fee will be charged on all unused parts which are returned.
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
24
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
Warranty
Equipment Covered Under This Warranty:
Model 05025
Warranty
Red Devil Equipment Co. warrants equipment manufactured by it and bearing its name to be free from defects
in material and workmanship.
Red Devil Equipment Co. will provide replacement parts caused by failure due to production or manufacturing
error for a period of two years. Costs of labor and transportation for service of machines under this warranty
will also be covered during the warranty period. Normal ground freight will be covered for replacement parts
sent within the warranty period. UPS Ground or common carrier ground freight will be covered for the return of
defective items only.
This warranty applies only when the equipment is installed, operated, and maintained in accordance with
written Red Devil Equipment Co. instructions as appearing in the owners' manuals.
This warranty does not cover, and Red Devil Equipment Co. shall not be liable for, any malfunction, damage,
or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance,
negligence, accident, tampering, or substitution of non-red Devil Equipment Co. component parts, modification
or use for non-intended purposes. Nor shall Red Devil Equipment Co. be liable for malfunction, damage,
or wear caused by the incompatibility with Red Devil equipment Co. equipment of structures, accessories,
equipment, or materials not supplied by Red Devil Equipment Co.
Disclaimers and Limitations
The terms of this warranty constitute purchaser;s sole and exclusive remedy and are in lieu of any other
warranties, express or implied. In no case shall Red Devil Equipment Co.'s liability exceed the amount of
the purchase price. *All warranty repairs must be executed by a Red Devil Equipment Co. Authorized
Service Center or warranty will be voided.
Please contact your Red Devil Equipment Co. account representative at 800-221-1083 for specific questions
regarding warranty terms.
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
25
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
Notes
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
26
1786755 Rev A
ECO 13-0002 J
April 2014
Owner’s Manual: 05025 Gyro Mixer
Non-Explosion Proof Model
1786755 Rev A
ECO 13-0002 J
April 2014
www.RedDevilEquipment.com (PHONE) 800-221-1083 | (INTL) +1-763-533-2969 | (FAX) 763-852-1811
27
Owner’s Manual: 05025 Gyro Mixer
Non Explosion Proof
For sales or service, please contact:
Red Devil Equipment Company
Attn: Customer Service Department
14900 21st Ave N
Plymouth, MN 55447
USA
U.S. Telephone:
International Telephone:
Fax:
E-mail:
800.221.1083
+1.763.533.2969
763.852.1811
info@reddevilequipment.com
www.RedDevilEquipment.com
For instructional “How To” videos please visit:
www.RedDevilEquipment.com
Copyright 2014 Red Devil Equipment Company. All rights reserved.
1786755 Rev A
ECO 13-0002 J
April 2014