1. No category

Photoelectric Semi-Wireless Through-Beam Sensor
User Manual
Order Code: 95001
IN2 Access & Control Ltd.
Unit 6A Mile Oak, Maesbury Road Ind.Est., Maesbury Road, Oswestry, Shropshire SY10 8GA
Tel: 01691 655150, Fax: 01961 680630, Email: sales@in2access.co.uk, Web: www.in2access.co.uk
A1
Photocell beam sensor User Manual
(P/N 95001)
I. Technical Specification
1.
2.
3.
4.
5.
6.
7.
Working voltage: 12~24VAC/DC or 3V Dry Battery
Working current(24VDC):emitter: ≤8mA receiver: ≤40mA
Photocell wavelength: 940nm
Angle of opposite emission: ≤±5º
Receiver range: ≥12m
Internal Rotation system adjusted Angle: 0～180 º
Working temperature: -20º～+60℃
8. Relay contact loading capacity: 1A/30VDC
9. Size: 127*50*28mm
II. Safety Instruction
1. For security, please read the user manual carefully before initial operation;
2. This photocell is without any fuse, so Please make sure the power is off before installation;
3. Only used this system that do not cause any danger life or property during the running failure or its security risks
eliminated;
4. Please guarantee the products used in effective working range.
III. Picture Display
IN2 Access & Control Ltd.
Unit 6A Mile Oak, Maesbury Road Ind.Est., Maesbury Road, Oswestry, Shropshire SY10 8GA
Tel: 01691 655150, Fax: 01961 680630, Email: sales@in2access.co.uk, Web: www.in2access.co.uk
1
A1
IV. In
nstallation insttruction
4.1 You can
n choose exte
ernal power su
upply (12‐24V
V AC/DC) or Baattery supply J2
J in transmit module.
4.11.1 put the short circuit cap
p on Ext. Poweer, Supply volttage:12‐24V AC/DC
A
4.11.2 put the short circuit cap
p on BATTERY, Battery voltage:3V
4.2 You can set the buzzeer working or not
n by switch J3
4.2..1 Buzzer worrks when short circuit cap oon celled
4.2..2 Buzzer not work when sh
hort circuit caap on No celled
4.3
You caan set the swittch of photocell NO and NCC by jumper J5
5.
4.33.1 when the short
s
circuit cap
c on NO, Thee photocell will
w be Normal Open
4.33.2when the short
s
circuit caap on NC, the photocell will be normal cllosed
4.4 Installation
4.4.1
The photocells should
s
be insttalled more thhan 20cm abo
ove the groun
nd (to avoid reeflection), and the distancee
between emitteer and receiver shall be morre than 50cm..
End user should
d install the photocell on t he back of th
he direct sunlight or other strong light source (±5º) to
o
w
well stea
adily.
keeep photocell work
4.4.2
Avoid installing other infrared
d photocell em
mitters within the effective distance of reeceiver
4.4.3
If tthe end user need to install other photoocells in one same
s
straightt line , the recceivers could be installed in
n
thee two ends an
nd the emitterrs could be baack‐to‐back insstalled
4.4.4
Staable installation could avo
oid the signall of emitter and
a receiver skewing due to lightly vibrate and thee
maalfunction.
4.5 Wire co
onnection
4.5.1
You
u can choose safety switch for transmit m
module. If nott, it should be short circuit by the cap, PLLS see PIC 6.
4.5.2
PH
HOTO is the sw
witch contact and
a can selectt NO or NC.
LOW
W.BAT is the low
l voltage alarm switch too buzzer when working voltage of emitteer module is lower than 2V
V.
Alsso it can activaate the extern
nal alarm.
4.5.3
Power on after correct connection. You w
will find LED will
w turn on when
w
you makke alignment at the emitteer
and receiver, orr led will off. Photocell sw itch ‘PHOTO’ works in set‐‐up status(NO
O or NC, see 4.3). If there’’s
obstacle betweeen the transmit and receivee module
① Buzzer will beep (J3 at Ce
elled)
② ‘PHOTO’ sw
witch OFF or ON.
O When J5 is keep” NC””, alignment the emitter annd receiver, LED
L will be on
n,
photocell switch
h is ON; if som
meone or som
mething shelte
er the sensor, the Led will tturn off, phottocell switch is
OFFF.
Input
Input
Output
Output
IN2 Access & Control Ltd.
Unit 6A Mile Oak, Maesbury Road Ind.Est., Maesbury Road, Oswestry, Shropshire SY10 8GA
Tel: 01691 655150, Fax: 01961 680630, Email: sales@in2access.co.uk, Web: www.in2access.co.uk
2
A1
V Installation Pictures
1. Opening package
and taking out
accessories
2. Fixing the holder
location map on
wall
5. Fixing bottom
cover
6. Put upper
cover on
3. Drilling, and
fixing expansion
pipe
7. Screw bottom and
upper cover together
4. Connecting
lines
8.
Finished
IN2 Access & Control Ltd.
Unit 6A Mile Oak, Maesbury Road Ind.Est., Maesbury Road, Oswestry, Shropshire SY10 8GA
Tel: 01691 655150, Fax: 01961 680630, Email: sales@in2access.co.uk, Web: www.in2access.co.uk
3