Specification for Buzzer Page Revision No. Model No. : SPA-G1712-K8098 Drawing No. 2/9 1.0 OEM8098R CONTENTS 1. Scope 2. General 3. Maximum Rating 4. Electrical Characteristics 5. Measuring Method !" 6. Physical Characteristics #$ 7. Environmental Characteristics %& 8. Dimensions '( 9. Packaging Standard )*+, 10. Cautions -. 11. Cautions for Use /012 12. Revision 345 Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com Page Revision No. 3/9 1.0 Drawing No. OEM8098R Specification for Buzzer Model No. : SPA-G1712-K8098 1. Scope This product specification is applied to the piezoelectric sounder in alarm systems.Please contact us when using this product for any other applications than described in the above. EFGHIJKLMNOPQRSITUVWXY-Z[\]MNOIP^_`a IJSP U 2. General 2.1 Out-Diameter : 17x17mm 678 17x17 mm 2.2 Height : 6.8mm 9:8 6.8 mm 2.3 Weight : 2 gr. ;<8 2= 2.4 Case Material/Color : PPS/Black >?@A/BC: PPS/D 3. 2 Maximum Rating Item EF Specification 3.1 9K Maximum input Voltage 1.5~16VDC 3.2 : Operating Temperature Range -20 +80 3.3 : Storage Temperature Range -30 +100 4. Electrical Characteristics 2 Item EF Specification 4.1 K Sound Pressure Level #80dB at 12VDC/10cm 4.2 Resonant Frequency 4.0± 0.5KHz 4.3 Max.Rated Current 4.4 ! Tone Nature "10mA at 12VDC Continuous 2 Refer to next item for measuring method. Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com Page Specification for Buzzer Revision No. Model No. : 5. SPA-G1712-K8098 !" 5.1 K 45 Drawing No. 4/9 1.0 OEM8098R Measuring Method S.P.L. Measuring Circuit 67:12VDC Input Signal:12VDC 10cm Mic. K3O piezoelectric sounder Amp. MIC : ND10 Q$%Z&' MIC : ND10 Sound Meter or equivalent 8K9 : DF1730SL2A Z&' DC Power Supply : DF1730SL2A or equivalent 5.2 %& Measuring Condition :+25± 3P):60± 10%R.H.+, ,):4585%R.H.]2 . *+,T,-.]/,01T:+5+35 Part shall be measured under a condition (Temperature :+5 to +35 ,Humidity :45 to 85%R.H.)unless the standard condition (Temperature :+25 (3,Humidity :60 (10 %R.H.) is regulated measure. 6. #$ Physical Characteristics 6.1 QOP Shock 6.2 Q<= Vibration Resistant :;FEF Specification :; Test Condition :;2 Item GHIJ:490m/s2 KLMXYZ@A !BC3NOP:;F 3O Sounder shall be measured after being applied shock(490m/s2) for each three mutually perpendicular directions to each of 3 times by half sine wave. <= 1055 Hz,1.5mm ><?,XYZ @A!BC2DE ;F, 3O. 51]R The measured value shall meet Table 1. Sounder shall be measured after being applied vibration of amplitude of 1.5mm with 10 to55Hz band of vibration frequency to each of 3 perpendicular directions for 2 hours. Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com Specification for Buzzer Page Revision No. Model No. : SPA-G1712-K8098 Drawing No. 5/9 1.0 OEM8098R 6. #$ Physical Characteristics Q 6.3 Soldering Heat Resistance :;FEF Specification :; Test Condition :;2 Item `3O]VWV(V 3O>? 1.5mm) +300(5]3(0.5^ Z+260(5]10(1^,FTRW 4DEF, 3O. Lead terminal are immersed up to 1.5mm from sounder's body in solder bath of +300(5 for 3(0.5 seconds or(260(5 for 10(1 seconds, and then sounder shall be measured after being placed in natural condition for 4 hours. _`3O]VW`a5^,F `+260(5]W3(0.5^. 6.4 6.5 0 Solderability VW: Terminal Strength Pulling Lead terminals are immersed in rosin for 5 seconds and then immersed in solder bath of +260 (5 for 3(0.5 seconds. STTUAVW]XBYI9.8Z[]\] ;10^. The force 10 seconds of 9.8N is applied to each terminal in axial direction. 51]R The measured value shall meet Table 1. VW590%1 ).(V W]6) 90% min. lead terminals shall be wet with solder. (Except the edge of terminal) VW, 0] No visible damage and cutting off Recommendable reflow soldering condition is as follows. Note 1; It is requested that reflow soldering should be executed after heat of product goes down to normal temperature. Note 2; Peak reflow temperature of 260 , with a maximum duration of 60 sec. between 220 and 260 6.5 Reflow Soldering Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com Page Specification for Buzzer 6/9 1.0 Revision No. Model No. : SPA-G1712-K8098 Drawing No. OEM8098R 7. %& Environmental Characteristics 7.1 :;FEF Specification :; Test Condition :;2 Item J:+100(2] !296DEP F "PTR4DEFP 3 O 9 Dry Heat Test (Storage) After being placed in a chamber with +100(2 for 96 hours and then being placed in natural condition for 4 hours, sounder shall be measured. J:-30(2]#$!296DEP F "PTR4DEFP 3O 7.2 7.3 7.4 * After being placed in a chamber with -30 ( 2 for 96 hours and then being placed in natural condition for 4 hours, sounder shall be measured. Cold Test (Storage) 51]R The measured value shall meet Table 1. J 90%95% R.H., :+40(2] %& ;!296DEPF "PTR 4DEFP 3O Q) Humidity After being placed in a chamber with 90 to 95%R.H. at +40± 2 for 96 hours and then being placed in natural condition for 4 hours, sounder shall be measured. :)% Temperature Cycle _J:-30(2]#$!230SPF J%(+20)15SF, J+100(2] !230 SP &J%(+20)15S. '(1)%5N,TR4DEFP 3O After being placed in a chamber at -30(2 for 30 minutes, sounder shall be placed at room temperature(+20).After 15 minutes at this temperature ,sounder shall be placed in a chamber at +100(2. After 30 minutes at this temperature, sounder shall be returned to room temperature (+20 ) for 15 minutes. After 5 above cycles, sounder shall be measured after being placed in natural condition for 4 hours. 51 2 Item K$ Sound Pressure Level Ningbo Kepo Electronics Co.,Ltd. Table 1 ;F+,< Specification after test -.H ± 10dB Initial Value(10dB http://www.chinaacoustic.com Specification for Buzzer Model No. : SPA-G1712-K8098 Page 7/9 Revision No. 1.0 Drawing No. OEM8098R 8. Dimensions KEPO /0123 FIRST ANGLE PROJECTION UNIT : mm Tolerance : ± 0.5 Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com Specification for Buzzer Model No. : SPA-G1712-K8098 9. )*+, Page Revision No. 8/9 1.0 Drawing No. OEM8098R Packaging Standard ]6)* !S9a!"]+#$7<"%&;'7 T(]()W*+AB,#$ Each minimum package unit of products shall be in a carton box and it shall be clearly marked with Part Number, quantity and outgoing inspection number. There shall be no mechanical damage on products during transportation and/or in storage. 10. -. Cautions ^_4IJ90]*E U1]I ? Please contact us before using our products for the undermentioned applications requiring especially high reliability in order to prevent defects which might directly cause damage to other party'slife, body or property(listed below). SAircraft equipment TUVW XAerospace equipment YZVW [Undersea equipment \]VW ^Medical equipment _`VW aTransportation equipment (automobiles,trains ,ships) QVY Traffic signal equipment Q67VW Disaster prevention/crime prevention equipment VW Data-processing equipment VW Applications of similar complexity or reliability requirements comparable to the applications listed in the above 1Z0R9]VW 11. /012 Cautions for Use 11.1 ^_LM]#$9NO(E]H,P0QR. The component may be damaged if mechanical stress over this specification is applied. 11.2 /0;@5ABCDE,FG:+,HIJKK. Please pay attention to protect operating circuit from surge voltage provided by something of force such as failing ,shock and temperature changing. 11.3 T4I56]78,9/056:]:9a;<T+3501,=>E? #T3^2. In case of using solder iron for soldering, the top of soldering iron's temperature should be kept less than +350 .Moreover the soldering time should be also kept with in 3seconds. Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com