Technical Information agricultural and construction engine Spray Paint ColorMatic agricultural and construction engine acrylic spray paint is a premium, high-finished acrylic coat with high-finish - specially formulated for quick coating of industrial surfaces. Thanks to the broad-jet atomization, it can also be used on larger surfaces. An extremely high content of pigments and specific additives provides high coverage, high film thickness, good hold and good adhesion direct on metal. To best prepare, thoroughly clean the surface to be painted with ColorMatic Silicone Remover no. 174469 and, as required, apply a primer or filler (e.g. ColorMatic 2K Primer Filler no. 195 327). In addition, we recommend the use of ColorMatic Spot Blender no. 114 229 for spot repair on edges. Application: Ideal for spot repairs and refinishing parts Quality and properties High-quality acrylic coat Simple application Professional jet atomization ensures that it can be used for larger surfaces Extremely high pigmentation and specific additives provide high coverage High film thickness with good hold Light blending Physical and chemical data Basis of binder: Acrylic Colour: Specific Smell: solvent Degree of gloss: (at measurement angle 60° acc. to DIN 67530) glossy: 80 gloss units Efficiency: Depending on consistence and colour of the ground: 400 ml are sufficient for approx. 0,8 - 1,0 m² Substrate: ColorMatic 2K Primer Filler no. 195 327 ColorMatic 1K Primer for Aluminium no. 190 278 ColorMatic 1K Primer for Zinc no. 190 285 ColorMatic 1K Epoxy Primer no. 174 414 ColorMatic 1K Filler, beige no. 856 556 ColorMatic 1K Filler, grey no. 874 987 Cured paint, polished ColorMatic 1K Primer Filler: HG 1 white no. 856 532 HG 2 light grey no. 882 425 HG 3 grey no. 856 525 HG 4 tele grey no. 644 719 HG 5 basalt grey no. 882 432 HG 6 graphite grey no. 882 449 HG 7 black no. 549 663 HG 8 red no. 856 549 Drying time (at 20°C, 50% relative air humidity): Dust-dry: after approx. 10 Minuten Dry to touch: after 30 minutes The drying time depends on surrounding temperature, air humidity and thickness of the applied coat. Temperature resistance: to 90°C Storage stability: 10 years if appropriabte storage provided (=10°-25°C, relative air humidity of max. 60%) Size: Aerosol cans, maximum nominal volume 400 ml VOC-value: 272,7 g Environment and labelling Environmentally sound: The products of MOTIP DUPLI are 100% free of heavy metals. The caps and packagings are made of recyclable material. Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse". Marking/Labelling: All products made by MOTIP DUPLI comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200 and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version. Using instructions Before use, carefully read and observe the warning texts on the label! Clean surfaces to be painted thoroughly with ColorMatic silicone remover no. 174469, then sand The area must be dry and free of dust and grease Shake can well for 2 minutes Carry out spray test 2-3 coats For professional use only Wear an appropriate respirator (recommended type A2/P3) Disclaimer of liability This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI. For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 8h a.m. to 5 h p.m. or on Friday until 12 h p.m. As of October 05, 2011 This release replaces all eventually earlier issued versions Print date: 15.10.2014 MOTIP DUPLI GmbH | Kurt-Vogelsang-Straße 6 | 74855 Haßmersheim | info@dupli-color.de