1. business and industrial
2. agriculture and forestry
3. forestry

SOLAR CONTROL FILMS 08 87 13
®
CPFilms Inc.
P.O. Box 5068
Martinsville, VA 24115
Phone: (800) 255-8627
Phone: (276) 627-3000
Fax: (276) 627-3032
E-mail: cpfilms@cpfilms.com
www.cpfilms.com
This MANU-SPEC®utilizes the Construction Specifications Institute (CSI) Project Resource Manual (PRM) including
MasterFormat™, SectionFormat™ and PageFormat™. A MANU-SPEC is a manufacturer-specific proprietary
product specification using the proprietary method of specifying applicable to project specifications and master
guide specifications. Optional text is indicated by brackets [ ]; delete optional text in final copy of specification.
Specifier Notes typically precede specification text; delete notes in final copy of specification. Trade/brand names
with appropriate symbols typically are used in Specifier Notes; symbols are not used in specification text. Metric
conversion, where used, is soft metric conversion.
This MANU-SPEC specifies solar control window films. These products are manufactured by CPFilms Inc. Revise
MANU-SPEC section number and title below to suit project requirements, specification practices and section
content. Refer to CSI MasterFormat™ for other section numbers and titles.
SECTION 08 87 13
SOLAR CONTROL FILMS
PART 1 GENERAL
Specifier Note: Article below includes submittal of relevant data to be furnished by Contractor either before, during or after construction.
Coordinate this article with Architect’s and Contractor’s duties and responsibilities in Conditions of the Contract and Section [01 33 00 Submittal Procedures].
1.01 SUBMITTALS
A.
General: Submit listed submittals in accordance with Conditions of the Contract and Section [01 33 00 - Submittal
Procedures] [___________].
B.
Product Data: Submit product data, including manufacturer’s SPEC-DATA sheet, for specified products.
C.
Samples: Submit 8 1/2 inch×11 inch (216× 279 mm) samples of specified film(s) applied to 6 mm (1/4 inch, nominal) clear
glass.
D.
Quality Control Submittals:
E.
1.
Certificates: Manufacturer’s certification that the installer is acceptable.
2.
Manufacturer’s Instructions: Manufacturer’s installation instructions.
Closeout Submittals:
1.
Warranty: Manufacturer’s standard warranty document executed by authorized company official. Manufacturer’s
warranty is in addition to, and not a limitation of, other rights Owner may have under Contract Documents.
Specifier Note: Article below should include prerequisites, standards, limitations and criteria that establish an overall level of quality for
products and workmanship for this section. Coordinate article below with Division 01 Quality Assurance Section.
1.02 QUALITY ASSURANCE
A.
Installer Qualifications: Acceptable to the manufacturer.
B.
Regulatory Requirements: In accordance with Section [01 41 00 - Regulatory Requirements] [___________].
1.03 DELIVERY, STORAGE & HANDLING
A.
General: Comply with Section [01 61 00 - Common Product Requirements] [___________].
B.
Delivery: Deliver materials in manufacturer’s original, unopened, undamaged containers with identification labels intact.
®
®
SPEC-DATA and MANU-SPEC are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2008 Reed Construction Data. All Rights Reserved.
SOLAR CONTROL FILMS 08 87 13
®
C.
CPFilms Inc.
Storage and Protection: Store materials protected from exposure to harmful environmental conditions and at temperature
and humidity conditions recommended by the manufacturer.
Specifier Note: Coordinate article below with Conditions of the Contract and with Section 01 78 36 - Warranties.
1.04 WARRANTY
A.
Project Warranty: Refer to Conditions of the Contract for project warranty provisions.
B.
Manufacturer’s Warranty: Submit in accordance with Section [01 78 36 - Warranties] [___________] for Owner’s
acceptance, manufacturer’s standard warranty document executed by authorized company official. Manufacturer’s warranty
is in addition to, and not a limitation of, other rights Owner may have under Contract Documents.
1.
Warranty Period: 10 years commencing on Date of Substantial Completion.
PART 2 PRODUCTS
Specifier Note: Retain article below for proprietary method specification. Add product attributes, performance characteristics, material
standards and descriptions as applicable. Use of such phrases as “or equal,” “or approved equal” or similar phrases may cause
ambiguity in specifications. Such phrases require verification (procedural, legal and regulatory) and assignment of responsibility for
determining “or equal” products.
2.01 SOLAR CONTROL FILMS
Specifier Note: Paragraph below is an addition to CSI SectionFormat and a supplement to MANU-SPEC. Retain or delete paragraph
below per project requirements and specifier’s practice.
A.
Manufacturer: CPFilms Inc.
1.
Contact: P.O. Box 5068, Martinsville, VA 24115; Telephone: (800) 255-8627, (276) 627-3000; Fax: (276) 627-3032;
E-mail: cpfilms@cpfilms.com; website: www.cpfilms.com.
Specifier Note: Retain film(s) below to conform to project requirements. If more than one is retained, create designators and coordinate
with drawings.
B.
C.
Llumar:
1.
Reflective Series: [R-15B CDF (Bronze)] [R-15G SR CEF (Gray)] [R-15BL SR (Blue)] [R-15GO SR PS (Gold)] [R-30B
SR CDF (Bronze)] [R-30G SR CDF (Gray)] [PCR-15BL SR CDF (Blue)] [PCR 35GN SR CDF (Green)] [R-20 SR CDF
(Silver)] [R-35 SR CDF (Silver)] [R-50 SR CDF (Silver)].
2.
Dual Reflective Series: [DR-15 SR CDF (Gray/Silver)] [DR-25 SR CDF (Gray/Silver)] [DR-35 SR CDF (Gray/Silver)]
[DR-45 SR CDF (Gray/Silver)].
3.
E Series: E-1220 SR CDF (Silver).
4.
Deluxe Series: [DL-05 G SR CDF (Grey)] [DL-158 SR CDF (Bronze)] [DL-15G SR CDF (Gray)] [DL-30GN SR PS
(Green)].
5.
N Series (Llumalloy): [N-1020 SR CDF (Neutral)] [N-1040 SR CDF (Neutral)] [N-1050 SR CDF (Neutral)] [N-1065 SR
CDF (Neutral)] [N-1020B SR CDF (Bronze)] [N-1035B SR CDF (Bronze)] [N-1050B SR CDF (Bronze)].
6.
Nonreflective Series: [NRM-PS2 (Frosty)] [NRMB-PS2 (Bronze)] [NRMM-PS3 (Black)] [NRMW-PS3 (White)] [UV CLSR PS (Clear)]
7.
Patterned Series: [R-15B SR CDF (stripes)] [R-15G SR CEF (bands)] [R-15BL SR PS (thin lines)] [R-15GO SR PS
(small dots)] [R-30B SR CDF (mini dots)] [R-30G SR CDF (matte squares)] [PCR-15BL SR CDF (squares)] [Frosted
Sparkle] [NRMFRPSRHPR].
8.
Graphic Arts Series: [BLUE SR HPR] [GREEN SR HPR] [RED SR HPR] [YELLOW SR HPR]
9.
Safety Series: [SCL SR PS4] [SCL SR PS6] [SCL SR PS7] [SCL SR PS8] [SCL SR PS11] [SCL SR PS15] [R-30B SR
PS4] [R-20 SR PS4 & 8] [N-1020 SR PS4 & 8] [N-1040 SR PS4 & 8] [N-1050 SR PS4 & 8] [NUV65 SR PS4].
10.
Graffiti Series: [GCL SR PS4] [GCL SR PS6].
11.
Exterior Series: RK-20 PS (Silver).
Vista:
®
®
SPEC-DATA and MANU-SPEC are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2008 Reed Construction Data. All Rights Reserved.
SOLAR CONTROL FILMS 08 87 13
®
2.02
CPFilms Inc.
1.
Neutrals: [V33 SR CDF - Soft Horizons] [V45 SR CDF - Dayview] [V58 SR CDF - Crystal Begance].
2.
Dual Reflectives: [V14 SR CDF - Ultima] [V18 SR CDF - Celeste] [V28 SR CDF - Luminance] [V28 SR PS8 Luminance Safety] [V38 SR CDF - Mirage] [V38 SR PS8 - Mirage Safety] [V48 SR CDF - Nuance] [V33 BR SR CDF Sunrise Bronze].
3.
Harmony: [V31 SR CDF - Harmony Terre] [V40 SR CDF - Harmony Ciel] [V41 SR CDF - Harmony Terre] [V50 SR
CDF - Harmony Ciel] [V51 SR CDF - Harmony Terre].
4.
Low E: [VE35 SR CDF - Ambiance] [VE50 SR CDF - Radiance].
5.
Spectrally Selective: [VS42 SR CDF - Nova Stellaris] [VS60 SR CDF - SpectraSelect] [VS61 SR CDF - SpectraSelect]
[VS70 SR CDF - SpectraSelect] [VS75 SR CDF - SpectraSelect].
PRODUCT SUBSTITUTIONS
A.
Substitutions: Substitutions in accordance with Section [01 25 13 - Product Substitution Procedures] [No substitutions
permitted] [___________].
PART 3 EXECUTION
Specifier Note: Paragraph below is an addition to CSI SectionFormat and a supplement to MANU-SPEC. Retain or delete paragraph
below per project requirements and specifier’s practice.
3.01 MANUFACTURER’S INSTRUCTIONS
A.
Compliance: Comply with manufacturer’s product data, including product technical bulletins, product catalog installation
instructions and product carton instructions for installation.
3.02 EXAMINATION
A.
Site Verification of Conditions: Verify that conditions of substrates previously installed under other sections are acceptable
for product installation in accordance with manufacturer’s instructions.
3.03 PREPARATION
A.
Use protective tarps and dropcloths to cover interior finishes near window.
B.
Turn off or cover heating and air conditioning ventilation ducts.
C.
Clean window and window framing thoroughly with cleaning solution consisting of 90% water and 10% ammonia.
D.
Blade inside surface of window glass with industrial razors to ensure removal of foreign contaminants.
E.
Tape and seal cracked and deteriorating window sealant.
F.
Place towel or other absorbent material on window sill or sash to absorb moisture accumulation generated by film
application.
G.
Thoroughly rinse glass from top to bottom with pressure spray tank.
H.
Squeegee entire glass surface.
I.
Dry glass edges and window frames using a lint-free towel.
3.04 INSTALLATION
A.
Cut film edges neatly and square at a uniform distance of 1/8 inch (3 mm) to 1/16 inch (1.5 mm) of window sealant. Use
new blade tips after 3 - 4 cuts.
B.
Spray slip solution, composed of one capful of Johnson Baby Shampoo or Joy Dishwashing Liquid to 1 gallon of water, on
window glass and adhesive to facilitate proper positioning of film.
C.
Apply film to glass and lightly spray film with slip solution.
D.
Squeegee to remove water.
E.
Spray slip solution to film and squeegee a second time.
F.
Bump film edge with lint-free towel wrapped around edge of a 5-way tool.
G.
Wipe frame edge dry.
H.
Inspect installation to ensure proper application.
I.
Upon completion of film application, allow 30 days for moisture from film installation to dry thoroughly and to allow film to dry
®
®
SPEC-DATA and MANU-SPEC are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2008 Reed Construction Data. All Rights Reserved.
SOLAR CONTROL FILMS 08 87 13
®
CPFilms Inc.
flat with no moisture dimples when viewed under normal viewing conditions.
3.05 CLEANING
A.
Proceed in accordance with Section [01 74 23 - Final Cleaning] [___________].
B.
After application of film, wash film 30 days after application using common window cleaning solutions, including ammonia
solutions. Do not use abrasive type cleaning agents and bristle brushes to avoid scratching film. Use synthetic sponges or
soft cloths.
C.
Upon completion and verification of performance of installation, remove surplus materials, rubbish, tools and equipment.
END OF SECTION
®
®
SPEC-DATA and MANU-SPEC are registered trademarks of Reed Elsevier Inc. The three part MANU-SPEC format conforms to the editorial style of the Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2008 Reed Construction Data. All Rights Reserved.