1. home and garden
2. home furnishings
3. lamps and lighting

HAL
LIGHTING AND BUILDING CONTROL
MASTER CONTROL PANEL
WITH REMOTE CONTROL (IR4-4)
SCENE RECALL PLATE (SR4)
CONTROL WITH OLED
DOLLY SWITCH
Set and control complete room lighting scenes with one touch
www.focus-sb.co.uk
HAL | HOME AUTOMATED LIGHTING
HAL Lighting and Building Control
Control your lighting easily from one control plate or remote control with the
HAL home automated lighting system available from Focus SB.
• Control plates to match most of Focus SB products
• Simple, easy to use controls (programming knowledge not required)
• Contractor/installer can self-commission on smaller systems
• System settings unaffected by power failure
• System can be upgraded and added to at a later stage (modular concept)
• Larger multi-channel panels available to order
• Multi-channel systems can be housed in a central or multiple locations
• Control plates, panels and cubicles all connected on 1-10V CAT5 data loop
• Control options available for high frequency fluorescent luminaires and LEDs with suitable dimmable drivers
• Momentary ‘push to make’, rotary and infra-red only options are available to order
• Simple generic infra-red control available (system can also be controlled by intelligent infra-red ‘learning’ handset i.e. Logitech Harmony)
• System capability – 240 zones – 128 channels per zone – 8 scenes per zone – larger system on application. Can be interfaced with home entertainment systems i.e. Crestron, Opus etc., details on application
Control Plates to match your standard plates
Give an integrated look to your project with control plates designed to your
specification, to match your standard plates and in the finish of your choice.
The HAL system can be operated by ‘retractive’ rocker
or dolly switches and bell pushes, enabling a
harmonious installation in listed, period and historic
properties. Details on application.
Dolly Switches
Rocker Switches
Bell Push Switches
HAL Bespoke
Multi Channel Bespoke Systems
The modular concept of building-up a comprehensive HAL lighting control
installation utilising ‘off the shelf’ individual control panels enables a system
to be configured quickly and cost effectively. However, on larger
installations or in situations where space is limited Focus SB can supply
bespoke multi channel control panels. The lighting control components of
our bespoke units are din rail mounted with MCB protection for each pcb,
mains supply isolation switch, single or three phase input (as required),
exhaust fan and thermostat, panic over-ride link and all internal wiring.
Bespoke panels can be as small as eight channels ranging up to larger
individual or multiple enclosures housing twenty, sixty, even eighty or more
channels. Priced and quoted upon application.
2
HAL | HOME AUTOMATED LIGHTING
Master
Control Plate
HAL IR4-4
4 scene master
control plate
The HAL IR4-4 eight button master
user can still raise and lower light
control has four blue LED illuminated
levels on the individual channel
scene buttons, located on the left
buttons without affecting stored
hand side of the control plate, four
settings. To turn the system off, simply
channel buttons on the right hand
press the illuminated scene button.
side and central infra-red port.
An individual channel can be simply
turned on or off with a brief push at
Each of the four right hand channel
any time without effecting stored
buttons control one lighting circuit.
settings. To turn the system on just
Simply pressing and holding the
press one of the scene buttons. The
respective channel button enables
user can also program and select
the lighting level to be successively
scenes remotely using the optional
raised and lowered. Release the
HAL REM2 infra-red handset.
button when the desired level is
achieved. Repeat the procedure on
For systems that require a different
each of the remaining channel
combination of buttons please
buttons. Select one of the four scene
contact our sales office.
button to store the chosen settings to,
then press and hold the chosen
Need more control options?
button for a few seconds. The 4 scene
See page 6, HAL IR4 - 12
buttons will briefly flash on and off for
a few seconds, the selected
Technical Specifications
Buttons
Menu Function
storage
Operating Temp
Module Dimensions
Plate Dimensions
(typical)
Back Box
Infra-red 4 x blue illuminated scene recall/store
4 x channel/circuit
Scene selection, scene
0-40°C ambient
50mm x 50mm x 26mm
86mm x 86mm x 30mm
Standard UK 35mm deep
single gang
Receiver mounted to centre of plate
scene button then illuminating
constantly indicating successful
With smaller systems (i.e. 1, 2 or 3 channels)
scene storage.
buttons can be de-populated off control plate
Even though the scene buttons
– ask Sales office for details.
now have stored settings the
Price
HAL IR4-4
£195.00
All prices exclude VAT
3
HAL | HOME AUTOMATED LIGHTING
Scene Recall
Control Plate
HAL SR-4
4 scene recall
control plate
Technical Specifications
Buttons
Menu Function
Operating Temp
Module Dimensions
Plate Dimensions
(typical)
Back Box
Infra-red
4 x blue illuminated scene recall
Scene selection, off
0-40°C ambient
50mm x 50mm x 26mm
86mm x 86mm x 30mm
The user just presses the chosen
simply recalls scenes that have
scene button on the HAL SR - 4 to
previously been programmed and
activate the scene. Pressing the
stored using one of the HAL master
illuminated scene button again turns
control plates or HAL REM2
the system off.
infra-red remote handset.
Standard UK 35mm deep
single gang
No
Price
HAL SR-4
All prices exclude VAT
4
The HAL SR - 4 scene recall control
The HAL SR - 4 does not have an
The HAL SR - 4 is an ideal addition
infra-red receiver or programming
when the user requires control of their
facility and would normally be used in
HAL system from multiple points in a
addition to HAL master controls.
room or where system control is
£135.00
required adjacent to several access
Need more control options?
points into a room and on larger more
See page 6, HAL IR4 - 12
comprehensive systems.
HAL | HOME AUTOMATED LIGHTING
HAL REM2
Infra-red remote handset
The HAL REM2 infra-red handset enables
the user to programme, store and
recall lighting settings that have
previously been stored into the
HALsystem. The HAL REM2 has
four scene buttons and a keypad
for selection of up to 16 channels.
There is an additional system off button
that turns off all lighting channels.
To operate the HAL REM2 infra-red handset,
simply point it in the direction of the master
control plate in the controlled room and press
chosen function button.
Remote
Control
Technical Specifications
Buttons
Menu Function
Operating Temp
Module Dimensions
Infra-red
4 x scene recall, numeric keypad
8 x channel/circuit
1 x system off, 1 x shift facility
4 x spare (future use)
Scene selection, scene store, channel select,
raise and lower channel levels, channel 9-16 shift
0-40°C ambient
145mm x 40mm x 12mm
Enabled
As with the HAL master scene control plate, the user is
able to set scenes or raise and lower individual lighting
channels if desired without affecting the stored settings.
The HAL REM2 infra-red handset allows the user the
same level of control as experienced from HAL Master
Control plates.
Price
HAL REM2
£75.00
All prices exclude VAT
New HAL Net Box
Control your HAL system from your iPod
Touch, iPhone or iPad
The HAL Net Box is a network interface to
control your HAL lighting control system from
an iPod Touch, iPhone or iPad over your
wireless home network. The Net Box app
HAL
Lighting and
Building Control
allows control, configuration and setting of:
• Scenes
• Circuits
• Time based actions
• GPS triggered welcome home scenes
Technical Specifications
Supply
Outputs
Cable Entries
Control Input
DMX 512
Indicators
Operating Temp
Enclosure
Net Connection
5v power adaptor supplied
RS232
3 x 20mm 1 x 16mm glands
Hy-Net serial data
Available option
Power LEDs
0-30°C ambient
Plastic Solo DSI
RJ45
• Room scene and circuit names
Location monitoring will work in the
ELECTRICAL ACCESSORIES
Net Box
background when enabled. The app can be
downloaded direct to your Apple device from
an iTunes account.
Price
HAL Net Box
£395.00
All prices exclude VAT
HAL NET BOX requires specialist setting up,
Requires on-site commissioning, price on
programming and interfacing with customers
application.
iPad or iPhone at point of system
programming and commissioning.
5
HAL | HOME AUTOMATED LIGHTING
Master
Control Plate
HAL IR4 - 12
4 scene, 12 channel master control plate
Technical Specifications
Buttons
Menu Function
storage
Operating Temp
Module Dimensions
Plate Dimensions
4 x blue illuminated scene recall/store
12 x channel/circuit
Scene selection, scene
Back Box
Infra-red
centre
Standard UK 35mm deep
two gang
Receiver mounted to
left of plate
0-40°C ambient
2 x 50mm x 50mm x 26mm
146mm x 86mm
With smaller systems (i.e. below 8 or 12
channels) buttons can be de-populated off
control plate – ask Sales office for details.
Price
HAL IR4 - 12
All prices exclude VAT
£390.00
The HAL IR4 - 12 sixteen button master control has four blue Led
illuminated scene buttons located on the left hand side of the control plate
and twelve channel (lighting circuit) buttons in three rows towards the right
hand side. Each of the twelve channel buttons controls one lighting circuit.
Simply pressing and holding the respective channel button enables the
lighting level to be raised and lowered. Release the button when the desired
level is achieved. Repeat the procedure on each of the remaining channel
buttons. Then select one of the four scene button to store the chosen
settings to, then press and hold the chosen button for a few seconds. The 4
scene buttons will briefly flash on and off for a few seconds, the selected
scene button then illuminating constantly indicating successful scene
storage. Repeat procedure for remaining scene buttons. Even though the
scenes have now been stored the user can still raise and lower individual
lighting channels if desired without affecting the stored settings. To turn the
system off, simply press the illuminated scene button. To turn the system on
just press the one of the scene buttons. The user can also program and
select scenes remotely using the HAL REM2 infra-red handset.
HAL control plate scene and button configuration can be changed to suit
specific applications. For example, the 16 button control plate above could
provide 8 scenes and 8 channels or 6 scenes and 10 channels. Spare buttons
can be removed if required at point of manufacture.
6
HAL | HOME AUTOMATED LIGHTING
7
HAL | HOME AUTOMATED LIGHTING
OLED
Control Plate
HAL IR4 - OLED
OLED control plate
The HAL IR4 - OLED master control is the first of a new
generation of HAL control plates that use the latest organic
LED display technology. Designed to fit in a standard UK
single gang back box.
Technical Specifications
Resolution
128 x 64 Pixels
Display
Organic LED
Buttons
4 x scene recall
Menu Function
Scene text input, icon selection, OLED display and button brightness, i.r enable, e.scene, plate lock-
out, etc
Proximity Detection Passive
Operating Temp 0-40°C ambient
Plate Dimensions 86mm x 86mm x 30mm
(typical)
Back Box
Standard UK 35mm deep
single gang
Display Size
36mm high x 22mm wide
Display Orientation 0, 90, 180 degrees
Display Colour
Blue
Icons
40 Predefined Icons
Infra-red
Discrete receiver within
OLED
Compatibility
HAL 4-400/150/LT,
HAL 4 - LED/HFDS,
HAL DR - 4DS
All HAL master and scene
recall controls
The blue display has a far superior contrast ratio and viewing
angle than the traditional LCD modules currently used in
small displays. This results in a display screen that is crystal
clear and can be read from virtually any angle. The OLED
screen is movement activated within a range of
several metres.
Price
HAL IR4 - OLED
All prices exclude VAT
£315.00
Each of the four illuminated scene buttons has an associated
icon which can be chosen via a menu selection of over 40
different pre-defined styles. Programmable descriptive text
for each scene is also chosen from the same push button
menu. When a scene recall button is pressed the selected
icon is initially displayed at twice its normal size for
confirmation of scene selection. A hidden infra-red receiver
within the OLED screen enables the user to program scenes
in to the HAL system and to select scenes if desired using the
HAL REM2 infra-red handset or via an additional HAL IR4-4
master control within same room.
Please order HAL REM2. HAL IR4-8 OLED also available, see
rear cover and main price list.
8
HAL | HOME AUTOMATED LIGHTING
9
HAL | HOME AUTOMATED LIGHTING
Control Panel
HAL 4-400/150/LT
Technical Specifications
4 channel 40 to 400 watt
(150 watt LED)
leading/trailing edge
dimming panel
Supply
Outputs
Outputs Fused
Surge
Phase Control
Turn On
EMC
Cable Entries
Glands
Control Plate Wiring
Low Voltage Out
Incoming MCB
Control Input
Internal Controls
Indicators
Operating Temp
Enclosure
Dimensions
230vac 50/60Hz 10amp
4 x 400w
Busmann CFF 5m
400amp 20msec
Mosfet
Soft Start Lamp Current
Iron Powder Core Chokes
4 x 20mm, 1 x 16mm
CAT5 Screened (4 x Twisted
Pair)
5vdc 100ma
Available option
HAL Serial Data
4 x Zone-Chan DIP Switch
Power & Diagnostic LEDs
0 - 40 °C Ambient
White Powder Coated Steel
220 x 160 x 70 mm
The HAL 4 - 400-150/LT is a four
When used in conjunction with control
channel dimming pack suitable for
plates from the Focus SB range, a
dimming and scene setting of four 40
scene based lighting control system
to 400 watt incandescent/low voltage
with infra-red capability can simply be
lamps loads (with suitable trans-
configured to suit installations both
formers) or 150 watt maximum load of
large and small, commercial or
mains dimmable LED lamps per
domestic. The control plates are
channel. All four outputs internally
connected to the dimmer panel using
Mains, low voltage tungsten/incandescent
Compatible and dimmable mains leading/
trailing edge LED lamps, luminaires and LED
strip lighting
Leading/trailing edge electronic transformers
and drivers
Suitable wirewound/toroidal transformers
switchable for use with leading edge
extra low voltage CAT5/6 type cable.
or trailing edge lamps/luminares. It is
Data communication is supported by
important for customer to check
the HAL protocol, which is a proven
suitability of installed lamps before
robust interface with an integral self
purchase and subsequent use with
monitoring facility.
4-400/150/LT is particularly suitable
System capability – 240 zones –
Multi-channel Bespoke control panel options
for ‘new generation ‘retro’ styled
128 channels per zone – 8 scenes per
available to order. HAL Control Panel options
decorative tungsten filament lamps.
zone – larger systems on application.
available for DALI, DSI and DMX luminaires -
New Mosfet controlled circuitry can
contact sales office.
help maximise filament life.
Suitable Loads
Prices
£495.00
HAL 4-400-150/LT All prices exclude VAT
HAL systems with more than 8 channels require
on-site commissioning and programming of
control panels and plates. Price on application.
Owing to constant changes and improvements
in lamp technology (especially LED lighting)
Focus SB are not able to guarantee compatibility
of lamps and luminaires with HAL lighting
control products. Please follow lamp and
luminaire manufacturers guidance for use with
dimming systems.
1010
lighting control systems. The HAL
HAL | HOME AUTOMATED LIGHTING
HAL 4-LED/HFDS
Control Panel
4 channel 1-10v LED
and HF fluorescent
dimmer panel
Technical Specifications
The HAL 4 - LED/HFDS is a 4 channel,
lighting control system with infra-red
1-10volt, analogue output dimmer,
capability can be simply configured to
designed to drive (1-10v) dimmable
suit installations both large and small,
fluorescent lamp ballasts and LEDs
commercial or domestic. The control
with suitable 1-10v dimmable drivers.
plates are connected to the dimmer
Can also be used to ‘switch’ non
panel using low voltage CAT5/6 type
dimmable loads as part of a scene.
cable. Data communication is
supported by the HAL protocol, which
Supply
Outputs
Relays
EMC
Dimming Control
Cable Entries
Glands
Low Voltage Out
DMX 512
Control Input
Internal Controls
Indicators
Operating Temp
Enclosure
Dimensions
230vac 50/60Hz
4 x 0 - 10vdc
4 x 10amp 100a inrush
R-C Suppression
0 - 10v Analogue
4 x 20mm, 1 x 16mm
5vdc 100ma
Available option
HAL Serial Data
4 x Zone-Chan DIP Switch
Power & Diagnostic LEDs
0 - 40 °C Ambient
White Powder Coated Steel
220 x 160 x 70 mm
Suitable Loads
High Frequency Dimmable 0-10v Fluorescent
Ballasts
LEDs with suitable 1 - 10V Dimmable Drivers
Each channel has it’s own power high
is a proven robust interface with an
Multi-channel Bespoke control panel options
inrush relay rated at 10amps to
integral self monitoring facility.
available to order. HAL Control Panel options
provide switched mains power to the
available for DALI, DSI and DMX luminaires -
ballasts (or to a contactor where there
System capability – 240 zones –
are a large number of ballasts). When
128 channels per zone – 8 scenes per
used in conjunction with control
zone – larger systems on application.
plates from the Focus SB range, a
scene based
contact sales office.
Price
£495.00
HAL 4-LED/HFDS All prices exclude VAT
HAL systems with more than 8 channels require
on-site commissioning and programming of
control panels and plates. Price on application.
Owing to constant changes and improvements
in lamp technology (especially LED lighting)
Focus SB are not able to guarantee compatibility
of lamps and luminaires with HAL lighting
control products. Please follow lamp and
luminaire manufacturers guidance for use with
dimming systems.
11
11
HAL | HOME AUTOMATED LIGHTING
Control Panel
HAL DR-4DS
Technical Specifications
4 channel universal digital
relay panel
Supply
230vac 50/60Hz
Relays
4 x 10amp
Protection
Voltage Transient
Suppression
Surge
100a high inrush relays
Phase Control
Leading Edge Triac
Turn On
Soft Start Lamp Current
EMC
RC suppression
Cable Entries
4 x 20mm, 1 x 16mm
Glands
Control Plate Wiring
CAT5 Screened (4
x Twisted Pair)
Low Voltage Out 5vdc 100ma
DMX 512
Available option
Panic Input
Forces All Channels to Full
Control Input
HAL Serial Data
Internal Controls 4 x Zone-Chan DIP Switch
Indicators
Power & Diagnostic LEDs
Operating Temp 0 - 40 °C Ambient
Enclosure
White Powder Coated Steel
Dimensions
220 x 160 x 70 mm
Suitable Loads
Electronic blinds, curtains, shutters, gates
Television, projection screens
Non-dimmable LED transformer
Non-dimmable lighting loads (i.e. exterior
floodlights,
garden lighting)
The HAL DR - 4DS is a four channel
switchable (non dimming) LED
universal digital relay module
transformers and drivers. When used
designed to control ancillary circuits
in conjunction with control plates from
as part of lighting scenes. These
the Focus SB range, a scene based
controlled power circuits can be
lighting control system with infra-red
electronic blinds, curtains, shutters,
capability can be simply configured to
gates, roof lights and television
suit installations both large and small,
projector screens. Non dimmable
commercial or domestic. The control
lighting loads like exterior
plates are connected to the dimmer
floodlighting and garden lighting can
panel using low voltage CAT5/6 type
also be controlled.
cable. Data communication is
supported by the HAL protocol, which
Each channel has its own high inrush
is a proven robust interface with an
power rated relay to provide switched
integral self monitoring facility.
mains power to the lighting ballast or
to a contactor where there are a large
System capability – 240 zones –
Multi-channel Bespoke control panel options
number of ballasts installed. The
128 channels per zone – 8 scenes per
available to order. HAL Control Panel options
module is also suitable for driving
zone – larger systems on application.
available for DALI, DSI and DMX luminaires contact sales office.
Price
HAL DR-4DS
£425.00
4 channel relay module
All prices exclude VAT
HAL systems with more than 8 channels require
on-site commissioning and programming of
control panels and plates. Price on application.
Owing to constant changes and improvements
in lamp technology (especially LED lighting)
Focus SB are not able to guarantee compatibility
of lamps and luminaires with HAL lighting
control products. Please follow lamp and
luminaire manufacturers guidance for use with
dimming systems.
12
MFC1
module
Ground Floor Zone 4
Entrance Hall
Standard retractive
rocker switch each linked
by ‘pair’ to MFC1
multifunction module
Ground Floor Zone 1
Dining Room
HAL Lighting
Control Panel
To Lighting Circuits
Ground Floor Zone 5
Kitchen
Ground Floor Zone 2
Lounge
HAL Lighting
Control Panel
To Lighting Circuits
Global Control
First Floor Zone 6
Master Bedroom
Ground Floor Zone 3
Family Room
Home and Away Timer
Cat5 e Data Cable
HAL REM2 Infra-red Remote
HAL SR - 4 Slave Recall
HAL IR4 - 4 Master Control
HAL IR4 - OLED Master Control
Key
HAL TYPICAL CAT 5 CABLING SCHEMATIC | SINGLE AND MULTIPLE CONTROL PANELS
13
HAL | PRICE LIST
14
HAL | PRICE LIST
Product
HAL Product Description
Trade Price
HAL IR4-OLED *
4 Button Master Control Plate with high definition multi-icon blue OLED screen. 4 scene recall
buttons. Programmable by HAL REM2 infra-red handset (optional extra) or HAL Master Control
Plate. Discrete infra-red port. Screen dims. 22mm wide x 36mm high. Typical plate dimensions
86 x 86mm.
£315.00
HAL IR4-8
OLED *
12 Button Master OLED Control Plate with high definition multi-icon blue OLED screen. 4
scene recall buttons and 8 channel/circuit dimming buttons. Discrete infra-red port. Screen
dims 22mm wide x 36mm high. Typical plate dimensions 146 x 86mm.
£495.00
HAL IR4-4 *
8 Button Master Control Plate with 4 blue LED illuminated scene recall/memory buttons and 4
channel/circuit dimming buttons, infra-red port, typical plate dimensions 86 x 86mm.
£195.00
HAL SR-4 *
4 Button Scene Recall Plate with 4 blue LED illuminated scene recall buttons, no infra-red port,
typical plate dimensions 86 x 86mm.
£135.00
HAL IR4-12 *
16 Button Master Control Plate with 4 blue LED illuminated scene recall/memory buttons and 12
no. channel/circuit dimming buttons, infra-red port, typical plate dimensions 146 x 86mm.
£390.00
HAL REM2
Infra-red remote handset with numeric keypad for control of up to 16 channels with 4 scene recall
buttons plus 4 auxiliary scenes, master off button. Batteries supplied.
£75.00
HAL 4-400/150/
LT
Four channel dimming pack suitable for dimming and scene setting of four 40 to 400 watt mains
incandescent/low voltage lamp loads (with suitable transformers) or 150 watt maximum load of
mains dimmable LED lamps per channel. All four outputs internally switchable for use with leading
edge or trailing edge lamps/luminaires. It is important for customer to check suitability of installed
lamps before purchase and subsequent use with lighting control systems.
£495.00
HAL 4-LED/
HFDS
Four Channel Dimming Pack suitable for dimming and scene setting of four 0-10 volt high
frequency fluorescent ballast circuits. Power relays each rated at 10amps providing switched
mains power to dimmable ballasts (or contactor if using larger numbers of ballasts). Also for use
with low voltage LED luminaires with suitable dimmable drivers.
£495.00
HAL DR-4DS
4 Channel Digital Relay Pack, for controlling non dimmable lighting or power circuits as part of a scene
(i.e. electronic blinds, curtains, blinds, shutters, gates, projector screens, heating and ventilation controls
etc) with four 10amp rated volt free n/o or n/c contact relays.
£425.00
HAL 4-DALI/DSI
Four Channel Dimming Pack. For dimming and scene setting in ‘broadcast mode’ 4 no. DALI or DSI high
frequency lamp loads.
£495.00
HAL HT
Home and Away Timer Control Plate, 2 LED illuminated buttons – 1 for scene event recording and 1
for random scene event playback, typical plate dimensions 86 x 86mm.
£195.00
HAL MFC1
Multi-Function module, mounted adjacent to switch position or at HAL control panel,
programmable for momentary, toggle, global and master on/off, timer, sequencer, holiday recall,
non HAL PIR interface. Also to enable HAL system use with retractive and push to make switches.
Three analogue inputs. Dimensions 50mm x 50mm x 26mm.
£125.00
HAL PIR **
Multi-functional sensor, with absence/presence detection. Programmable by HAL REM Infra
Red handset. Ceiling mounted in 35mm MR11 or 50mm MR16 downlighter housing (not supplied),
powered by Cat5/6 data connection.
£125.00
HAL NET BOX
Network Interface Module for control of HAL lighting system from iPod Touch, iPhone of iPad
over compatible wireless home network. ‘App’ is downloaded direct to Apple device from an
iTunes account. Allows control, configuration and setting of scenes, circuits, time based actions,
GPS triggered welcome home scenes etc. Requires specialist installation at time of HAL system
programming and on-site commissioning. c/w mains power supply. Dimensions 40mm x 45mm x
185mm
£395.00
HAL MIM**
Multi-function module. For use with retractive and ‘push to make’ switches. Converts analogue
input from conventional switches to digital coded output for use with HAL. Controlled switch
operates as scene recall unit. c/w IR sensor and flying leads for mounting behind switch front
plate in extra deep back box. Programmable for master, recall, momentary and toggle control,
global and master on/off. Use optional HAL REM2 for programming and master scene control.
Dimensions, 15mm x 50mm x 110mm approx. plus flying lead with IR sensor.
£125.00
HAL SOLO RL1**
Single channel relay module (rated at 6 amps) for controlling/switching power loads
(non dimmable lighting, electronic blinds, curtains, shutters, gates, projector screens etc.
Dimensions 40mm x 45mm x 185mm.
£195.00
(ex VAT)
HAL | PRICE LIST
HAL SOLO DS1**
Single channel dimming module suitable for dimming and scene setting of one 40 to
400 watt incandescent/low voltage lamps load (with suitable transformer) or 150 watt
maximum load of mains dimmable LED lamp. Output internally switchable for use with
leading edge or trailing edge lamps/luminares. Dimensions 40mm x 45mm x 185mm.
£195.00
HAL SOLO 1-10V **
Single channel dimming module suitable for dimming and scene setting of one circuit/
channel of suitable 1-10V high frequency lamps/luminaires. Dimensions 40mm x 45mm
x 185mm.
£195.00
HAL SOLO
LEDx4**
4 channel driver/dimmer module suitable for use with constant voltage/common
anode white dimmable LED strip lighting. Maximum load 25 watts per channel. Requires
specialist programming and commissioning as part of a complete HAL system.
Dimensions 40mm x 45mm - 185mm
£195.00
HAL SOLO RGB
**
Multi-channel module for use with suitable red/green/blue colour changing leds.
Requires specialist programming and commissioning as part of a complete HAL system.
Dimensions 40mm x 45mm x 185mm.
£195.00
HAL SOLO DALI/
DSI**
Single channel module for use with DALI/DSI enabled luminaires. Operates in ‘broadcast’ mode. Dimensions
40mm x 45mm x 185mm.
£195.00
*Control plate prices shown above are applicable for
most standard Focus SB plate styles and finishes to
match our other accessory products. HAL product code
should be suffixed with plate code - i.e HAL IR4-4 APS
(Ambassador Polished Stainless) HAL SR4 HSS (Horizon
Satin Stainless). Please contact sales office for further
advice.
** HAL SOLO modules are suitable for use in single
channel applications. They will require a suitable master
control plate (i.e HAL IR4-1). HAL SOLO modules can also
be used in addition to other HAL control panels (i.e HAL
4-400/150/LT) when additional circuits of a different
type and not controllable by the main panel are required
.
Hal systems larger than 4 channels as a minimum
require pre-programming before dispatch at additional
cost. Systems with 8 channels and larger (and with HAL
NET BOX) will require on site specialist programming
and commissioning at additional cost (please contact
sales office for further details).
Owing to constant changes and improvements in
lamp technology (especially LED lighting) Focus SB
are not able to guarantee compatibility of lamps and
luminaires with HAL lighting control products. Please
follow lamp and luminaire manufacturers guidance for
use with dimming systems.
Please note that
HAL Bespoke Multi
Channel Systems
are quoted
and priced on
application, please
contact sales
office.
Important Notice
It is the customer and installers responsibility to ensure that all lamps, luminaires, LED’s and LED ‘strip’
lighting products to be controlled by the HAL system are compatible and suitable for dimming and
lighting control. Focus SB can not be held responsible for damage caused to the customers lighting
products or the HAL lighting control and its system components by unsuitable products. Focus SB can
arrange testing of customers lighting products for suitability on request. This may be chargeable.
When installing individual HAL lighting control panels and modules all ‘incoming’ circuits must be
protected by a 10 amp type ‘B’ MCB. All individual ‘outgoing’ circuits should also be protected by a 2 amp
(max.) type ‘B’ MCB. Failure to do this may invalidate any applicable Focus SB warranty covering HAL
control panels, ancillary equipment and lighting products. All ‘bespoke’ HAL panels are supplied with full
circuit projection
15
Bespoke HAL
control plates available
HAL IR4-8 OLED
For further information about
HAL Lighting Control products
please visit our website
A large range of other plate
designs and finishes are
available to suit any interior style
www.design-matters.co.uk
www.focus-sb.co.uk
FREE DELIVERY TO MAINLAND UK |
01424 858060 | sales@focus-sb.co.uk
Prices effective 09/2014. E & OE.
Colours and finishes may vary due to printing processes.
www.focus-sb.co.uk