Download Report

What is Zetco Press-fit?
Zetco Press-fit is a range of ball valves, designed and manufactured with a built-in press connection.
This means fewer joints, less mess and major savings with reduced installation time. The integral
connection eliminates the use of additional fittings which means fewer leak points for every valve.
The range is manufactured under Zetco’s high standards in Italy. Rigorous design and testing has taken
place to ensure that Zetco’s premium quality is evident in this new range.
See the full range on the inside of this flyer.
Certification
The gas ball valves are certified by the Australian Gas Association (AGA) to AS 4617 and tested to DVGW
VP614. The water valves are WaterMarked by Iapmo R&T Oceana to AS 5830.1. The press-fit ends have
been tested to AS3688 and the material composition complies with AS2345.
What is the Warranty for Zetco Press-fit?
AGA 5301
AGA
5301
AS 4617
AS 4617
IAPMO WM-000110
AS 5830.1
STEP 1
Refer to the design guidelines overleaf for important dimensions
which must be considered prior to installation.
Use only Type A & B copper pipe complying with AS 1432.
Cut the copper pipe to the required length.
STEP 2
Carefully deburr the end of the pipe;
- INSIDE to minimise turbulence and pressure loss, and
- OUTSIDE to avoid damage to the o-ring during insertion.
For existing installations, ensure that the copper pipe complies
with AS 1432 and is free of defects and in good condition.
25
23
32
25
40
31
A
Nom. Size
mm
DN15
DN20
DN25
DN32
DN40
DN50
Measure and mark the correct insertion depth on the copper pipe.
20
22
50
39
0
mm
10
20
30
40
50
60
70
80
90 100 110 12
STEP 4
Ensure that you are using the correct valve or fitting for your
application (water or gas) and the o-rings are correctly positioned.
B
D
Zetco Press-fit must be installed according
to the installation instructions provided with
every valve and also available on our website.
Pipe OD
mm
12.70
19.05
25.40
31.75
38.10
50.80
E
A
mm
17
22
23
25
31
39
B
mm
10
10
10
20
20
20
C
mm
50
60
62
76
88
110
D
mm
60
60
60
60
60
60
Size (mm)
Min. Clearance
WATER APPLICATIONS
Medium
Potable water
Max. Temp.
110°C
Max. Pressure 2500 kPa
GAS APPLICATIONS
Medium
NG, LPG
Max. Temp.
100°C
Max. Pressure 2100 kPa*
*According to AS 5601 Table 4.1, operating pressure of consumer gas piping systems containing copper tube is limited to 200 kPa.
Disclaimer: Zetco Valves Pty Ltd will not accept responsibility for damage caused by failure to follow the instructions & warnings provided.
© 06-2014
Rest the raised bump in the groove of the press tool and operate
press tool according to manufacturer’s instructions. Inspect joint.
15
350
20
500
25
650
32
800
Unpressed connections may not be detected during
post-installation pressure testing due to a temporary
sealing effect of the o-rings. To ensure that correct
sealing has been achieved, visually inspect every joint
WARNING to ensure that each one is pressed correctly.
40
1000
Available for gas and water
50
1300
The most recent version of this
information sheet, plus additional
technical information can be
accessed at the Zetco website:
www.zetco.com.au
Disclaimer: Zetco Valves Pty Ltd will not accept responsibility for damage caused by failure to follow the instructions & warnings provided.
Press x press, press x female, press x male
Also available in nut & tail which includes
Zetco’s continuous flow hot water kits
For full details visit zetco.com.au
Phone 1300 659 639
Be Impressed
with Zetco
Full range 15-50mm
E
mm
80
85
86
88
94
106
Brazing or soldering close to press joints may result in damage to the o-rings.
The table below shows the minimum distance required between a press joint and any brazing
activity. In cases where this distance cannot be achieved, ensure that the valve or fitting is
adequately protected from heat and kept cool during the brazing procedure.
STEP 5
Push the valve or fitting onto the copper pipe up to the insertion
depth. Recheck engagement with the pipe prior to pressing.
NOT SUITABLE FOR
Solar hot water systems, medical gases, refrigeration and airconditioning gases, acetylene, urea solution, glycerin triacetate,
coolant inhibitor, sodium hydroxide or ammoniac gases.
Zetco Installation Instructions
BRAZING & SOLDERING
Check that the ends are completely free of swarf, sharp metal or
other debris which may cause damage the o-rings.
WARNING DO NOT USE MINERAL OIL TO LUBRICATE THE O-RINGS
AGA 5301
AGA
5301
AS 4617
AS 4617
The table below shows the minimum distances required between a press joint and other objects.
Clean the end of the pipe with emery paper or a soft scourer.
15
17
IAPMO WM-000110
AS 5830.1
SPACE REQUIREMENTS
C
STEP 3
Size (mm)
Depth (mm)
Press-fit Information
For use with Viega®, Rothenberger®, KemPress® V-profile tools only
INSTALLATION DESIGN INFORMATION
Follow carefully to avoid damage
© 06-2014
IMPORTANT INSTALLATION INSTRUCTIONS
Follow each step carefully
DESIGN GUIDE
Press-fit Information
For use with Viega®, Rothenberger®, KemPress® V-profile tools only
INSTALLATION INSTRUCTION SHEET
Zetco Valves warrants that the joint pressed by a Viega®, Rothenberger® or KemPress® V-Profile tool will
not leak for a minimum period of 25 years provided it is installed according to the installation instructions
provided with every valve and also available on the Zetco website. For our detailed warranty document
contact Zetco.
Email enquiries@zetco.com.au
(Aust Pat No 2006 200 845 & Pat Appln No 2013 242 783)
www.zetco.com.au
November 2014
Phone 1300 659 639
Email enquiries@zetco.com.au
www.zetco.com.au
ZETCO PRESS-FIT WATER BALL VALVES
DESCRIPTION
Water PxP Lever Handle
Water PxP T Handle
Water PxM Lever Handle
Water PxM T Handle
Water PxF Lever Handle
Water PxF T Handle
Water PxP Lever Lockable
Water PxM Lever Lockable
Water PxF Lever Lockable
Water PxP Lever Extension
SIZE
PACK
IAPMO WM-000110
AS 5830.1
DESCRIPTION
SIZE
CODE
PACK
Gas PxP Lever Handle
15
6200015
15
15
6100015
15
20
6100020
10
20
6200020
10
25
6100025
6
25
6200025
6
32
6100032
4
32
6200032
4
40
6100040
2
40
6200040
2
50
6100050
1
50
6200050
1
15
6103015
15
15
6203015
15
20
6103020
10
20
6203020
10
25
6103025
6
25
6203025
6
15
6102015
15
15
6202015
15
20
6102020
10
20
6202020
10
15
6105015
15
15
6205015
15
20
6105020
10
20
6205020
10
15
6101015
15
15
6201015
15
20
6101020
10
20
6201020
10
15
6104015
15
15
6204015
15
20
6104020
10
20
6204020
10
15
6107015
1
20
6107020
1
25
6107025
1
32
6107032
1
40
6107040
1
DESCRIPTION
SIZE
CODE
PACK
50
6107050
1
Water nut & tail
15MM
6301001
10
15X20MM
6301002
10
Gas PxP T Handle
Gas PxM Lever Handle
Gas PxM T Handle
Gas PxF Lever Handle
Gas PxF T Handle
15
6109015
1
20
6109020
1
Water nut & tail
20MM
6301003
10
Gas nut & tail
15MM
6302001
10
Gas nut & tail
15X20MM
6302002
10
Gas nut & tail
20MM
6302003
10
15
6108015
1
20
6108020
1
15
6110015
1
20
6110020
1
25
6110025
1
32
6110032
50
6110040
6110050
Tested to
DVGW
VP614
AGA 5301
AS 4617
ZETCO PRESS-FIT NUT & TAIL BALL VALVES
Water nut & tail
40
Note:
P = Press-fit
M = Male
F = Female
CODE
ZETCO PRESS-FIT GAS BALL VALVES
ZETCO PRESS-FIT HOT WATER KITS
1
DESCRIPTION
SIZE
CODE
PACK
1
Kit 1
20G, 20W
6310001
6
1
Kit 2
20G, 15X20W
6310002
6
Kit 3
20G, 15W
6310003
6
Kit 4
15G, 15W
6310004
6
Kit 5
15X20G, 15X20W
6310005
6
Kit 6
15X20G, 15W
6310006
6
Note: Kits include a gas nut & tail valve, a water nut & tail valve and a water outlet fitting.
November 2014