1. home and garden
2. home furnishings
3. lamps and lighting

Customer:
Date:
Project:
Qty:
Type:
M100
LED Recessed
-
Order Code:
Series
Light Engine
-
-
L10
L1R1
1A351
1A251,2
725lm/8.5W
per foot
Shielding
LW
Mounting
L10
1A301,2
638lm/7.3W
per foot
-
1A201,2
536lm/6.0W
per foot
-
-
-
Values calculated from a 4’ fixture @4000°K
using LW Shielding and standard driver.
For additional information please see page 2.
1 435lm/4.9W
per foot
Available starting at 2’ and up.
2
SF1
SF2
SF3
SG
DC
Mounting
L1R1 or
L1R2
TB3
TBS3
PMT3
RC 4
TS
Nominal
Fixture
Length
01
Finish
WH
Voltage
3000K
-
Continuous Flange
(Flangeless Endcaps)
35
2700K
-
L1R2
30
Emergency
Options
40
3500K
4000K
LED Optimized
white lens
Spackle Flange Spackle Flange Spackle Flange Slot Grid (9/16”) Decoustic
(1/2” Drywall) (5/8” Drywall) (After Drywall) (Wire Suspension Ceiling
or 1/4-20 stud)
(up to 2” thick)
T-Bar Length w/ T-Bar Length
suspension clips w/1” 1/4-20
Stud
1 ft.
025
2 ft.
03
3 ft.
04 5
4 ft.
T-Bar Length
Perimeter
Mount
055
5 ft.
Rotating
1” 1/4-20 Stud
Crossbar
(Ceilings 1/4” to
2” thick )
06 5 07
6 ft.
7 ft.
PM
Perimeter
Mount
085 XX
Runs (over 8’) & Configurations, round up to the nearest
foot and replace the “xx” with the # (i.e. 09=09’ nominal)
Individual fixtures, Runs and Configurations are supplied in nominal lengths to ensure full, even,
illumination. See pages 2 thru 6 for additional details.
BK
SV
120
277
UNV
120 Volt
277 Volt
120 thru 277
50/60hz capable
DL6
FS6
SS6
White
Damp Location
Rated
DM9,10
eldoLED 0-10V
(Linear)
EC12
Emergency
Circuit Wiring
Configuration IL9015
Lit Horizontal
Options
90° Corner
YEAR
-
Continuous Flange
(Flanged Endcaps)
27
Dimming
Options
5
-
Multi-Mount Form
CCT
Fixture
Options
LED WARRANTY
-
Black
In-line Fuse
DML9,10
eldoLED 0-10V
(Logarithmic)
SP
Silver
Separate
Switching
DMD9,10
eldoLED DALI
(Logarithmic)
8 ft.
Consult factory for lengths under 2’
5
Length intended to fit centered between the grid
for SG, TB, TBS, PMT mountings.
Custom colors are available, Please consult factory
CCEA7
CCEA
approved
DC29,10,11
Lutron 2-Wire
See page 8 for full details and restrictions
6
xxxx8
LED MR16 downlight
(replace “xxxx” with code from page 11)
DC39,10
Lutron 3-Wire
DCE9,10
Lutron Eco-System
Not available with EMN option
7
See page 11 for full details and restrictions
8
See page 7 for full details
9
Not available for 1’ length
10
120V only
11
See page 8 for full details and restrictions
12
120 or 277 Volt only
13
EM battery pack
(Non-IC-rated)
Lit Inverted
90° Corner
L1R1 only
4
Specify Premium Color
EMN13,14
V9015
3
Not available on lengths under 4’
14
IT9015
Lit “T” section
IX9015
Lit “X” section
See pages 9 and 10 for full details and
restrictions
15
ARRA
Compliant
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 1 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
3 15/16” (100mm)
4”
4”
(101mm)
(101mm)
3 11/16” (94mm)
3 / ” (100mm)
15 16
3 11/16” (94mm)
4 13/16” (122mm)
Construction:
Electrical/Performance:
Luminaire Finish:
Housing - Continuous, low copper 6063-T6
extruded aluminum profile with aluminum
endcaps, available as Individual fixtures (up to
12’) or Runs.
LED Light Engine - Brand-name mid-power
LEDs create a high efficiency LED light engine
able to provide a lumen maintenance of 96%
at 25,000 hours and 93% at 60,000 hours per
TM-21 report.
Powder Coat - All Selux luminaries are finished
in high quality polyester powder coating in our
Tiger Drylac certified facility and are tested in
accordance with test specifications for coatings
from ASTM and PCI.
Flange - 9/16” (14mm) wide flange runs full
lengths of both sides and is part of the main
extruded body. Specify continuous flange (L1R1)
or flush (L1R2) end cap . L1R2 does not work in
T-Bar ceiling.
LED Life - Calculated L70 greater than 398,000
hours and Reported L70 greater than 60,000
hours @ 25°C per TM-21
Geartray - Low copper 6063-T6 extruded aluminum profile.
Delivered Lumens - Due to LED manufacturer’s
tolerances the listed output has a ±5% tolerance. For outputs based on different shielding or
CCT please see photometry section at the end.
All products undergo a five stage intensive
pretreatment process where product is thoroughly cleaned, phosphated, and sealed. Selux
powder coated products provide excellent salt
and humidity resistance as well as ultra violet
resistance for color retention.
Shielding - Extruded, impact resistant acrylic
snap in lens:
- LED optimized white lens (LW)
Mounting(s) - Spackle in (drywall), Slot grid,
Decoustic, T-bar grid, Perimeter, Rotating Crossbar and Threaded Stud Mountings (see pages 3
thru 6 for details).
Standard Luminaire lengths - All standard
luminaires are supplied in nominal lengths to
ensure full, even, illumination. Runs and Configurations are available in approximately 1/4”
increments starting at the nominal 8’ fixture
length.
** Individual luminaires are not joinable in the
field.
Exact length luminaires - Individual luminaires, runs, and configuration are available
in exact lengths to meet your project needs.
Please consult factory with you requirements.
** Lens luminance may soften at the very ends
of the straight sections for exact length luminaires.
CCT - Available in 2700K, 3000K, 3500K and
4000K, tolerance within a 3-step MacAdam
ellipse.
Standard interior colors are White (WH), Black
(BK), and Silver (SV). Selux premium colors (SP)
are available, please specify from your Selux
color selection guide.
Warranty:
CRI - Min. 80
All Drivers - High efficiency, constant current,
soft start, Electronic Class 2 with a PFC>0.90.
For more detailed information on the available
drivers please see page 7.
Thermal Performance:
Ambient Operating Temperature - Luminaires
suitable for Max. ambient temperature of 35° C
(95° F) for all drivers, standard and optional.
Min. ambient temperature of:
-20°C (-4°F) for the Standard driver and optional
DML and DMD drivers
0°C (32°F) for the optional DC2, DC3 and DCE
drivers
L10 Joiner(s) - Runs and configurations are
supplied in multiple housing that are joined
together in the field using the supplied L10
Joiner System. This allows ease of installation
and ensures a uniform appearance (see page 8
for detail).
5 Year Limited LED Luminaire Warranty Selux offers a 5 Year Limited Warranty to the
original purchaser that the M100 series LED
luminaire shall be free from defects in material and workmanship for up to five (5) years
from date of shipment. This limited warranty
covers the LED driver and LED light engine when
installed according to Selux instructions and
operated within the Ambient Temperature. For
additional details and exclusions, see “Selux
Terms and Condition of Sale.”
Certifications and Compliance:
NRTL - For Dry and Damp location
(I.E. cULus; cCSAus)
ARRA Compliant
RoHS Compliant
IC-Rated *
*EMN option is Non-IC-rated
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 2 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
1/2” Spackle Flange Mounting (SF1)
1/2” Spackle Flange Mounting (SF1)
5/8” Spackle Flange Mounting (SF2)
5/8” Spackle Flange Mounting (SF2)
After Sheetrock Flange Mounting (SF3)
After Sheetrock Flange Mounting (SF3)
After drywall
installation
Spackle Flange Mounting (SF1, SF2 & SF3) - Dimensions
Nominal
Length
“A”
O.A.L. w/o Flange
“B”
End Suspensions
* “C” (Ref.)
Mid. Suspension
“D”
Feed Location
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
01 (1 ft.)
1' - 5/16"
313
0' - 1 5/8"
41
0' - 9 1/8"
231
0' - 4 1/8"
105
02 (2 ft.)
1' - 11 7/16"
595
0' - 1 5/8"
41
1' - 8 3/16"
513
0' - 4 1/8"
105
03 (3 ft.)
3' - 5/16"
923
0' - 6 1/8"
156
2' - 1/8"
612
0' - 2 1/8"
54
04 (4 ft.)
3' - 11 7/16"
1205
0' - 6 1/8"
156
2' - 11 3/16"
894
0' - 2 1/8"
54
05 (5 ft.)
4' - 11 7/16"
1510
0' - 6 1/8"
156
3' - 11 3/16"
1199
0' - 2 1/8"
54
06 (6 ft.)
5' - 11 7/16"
1815
0' - 6 1/8"
156
4' - 11 3/16"
1504
0' - 2 1/8"
54
07 (7 ft.)
6' - 11 7/16"
2119
0' - 6 1/8"
156
5' - 11 3/16"
1808
0' - 2 1/8"
54
08 (8 ft.)
7' - 11 7/16"
2424
0' - 6 1/8"
156
6' - 11 3/16"
2113
0' - 2 1/8"
54
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
1. 1/4-20 Threaded rod to struture (supplied and installed by others).
2. 14-20 Coupler hardware (supplied and installed by others).
3. 1” 1/4-20 Stud (by Selux).
4. Ø5/16” [Ø7mm] mounting hole.
5. Drywall/Sheetrock screw (Ref.)
6. Drywall/Sheetrock (Ref.)
7. 1/6” Plaster skimcoat (Ref.)
8. Drywall/Sheetrock tape (Ref.)
9. Blocking to secure fixture (by others)
10. Electrical connection box, removable side cover for electrical
connection pre-installation, once installed the wiring is accessible from below the ceiling through the luminaire.
11. Luminaires ship with the brackets pre-installed.
- The brackets cannot be removed until the fixture is completely
installed and secured through the spackle flange.
- Once the brackets are removed, the lens/louvers can be
installed.
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 3 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
Slot Grid Mounting (SG)
9/16” Slot Grid Mounting (SG)
(Wire Suspension or 1/4-20 Stud)
1. 9/16” Slot grid (shown as ref.)
2. Support wire to structure
(supplied and installed by others).
3. 1/4-20 Threaded rod to structure
(supplied and installed by others).
4. 1/4-20 Coupler hardware
(supplied and installed by others).
5. 1” 1/4-20 Stud (by Selux).
6. Ø5/16” [Ø7mm] mounting hole.
Slot Grid Mounting (SG) - Dimensions
Nominal
Length
“A”
Housing Length
Feet/Inch
MM
“B”
End Suspensions
Feet/Inch
* “C” (Ref.)
Mid. Suspension
MM
Feet/Inch
“D”
Feed Location
“E”
Grid Spacing
MM
Feet/Inch
MM
Feet
02 (2 ft.)
1' - 11 7/16"
595
0' - 1 5/8"
41
1' - 8 3/16"
513
0' - 4 1/8"
105
2’ Center to Center
04 (4 ft.)
3' - 11 7/16"
1205
0' - 6 1/8"
156
2' - 11 3/16"
894
0' - 2 1/8"
54
4’ Center to Center
05 (5 ft.)
4' - 11 7/16"
1510
0' - 6 1/8"
156
3' - 11 3/16"
1199
0' - 2 1/8"
54
5’ Center to Center
06 (6 ft.)
5' - 11 7/16"
1815
0' - 6 1/8"
156
4' - 11 3/16"
1504
0' - 2 1/8"
54
6’ Center to Center
08 (8 ft.)
7' - 11 7/16"
2424
0' - 6 1/8"
156
6' - 11 3/16"
2113
0' - 2 1/8"
54
8’ Center to Center
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Decoustic Mounting (DC)
Decoustic Mounting (DC)
(Panels up to 2” thick)
Decoustic Mounting (DC) - Dimensions
Nominal
Length
“A”
Housing Length
“B”
End Suspensions
* “C” (Ref.)
Mid. Suspension
“D”
Feed Location
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
01 (1 ft.)
1' - 5/16"
313
0' - 1 5/8"
41
0' - 9 1/8"
231
0' - 4 1/8"
MM
105
02 (2 ft.)
1' - 11 7/16"
595
0' - 1 5/8"
41
1' - 8 3/16"
513
0' - 4 1/8"
105
03 (3 ft.)
3' - 5/16"
923
0' - 6 1/8"
156
2' - 1/8"
612
0' - 2 1/8"
54
04 (4 ft.)
3' - 11 7/16"
1205
0' - 6 1/8"
156
2' - 11 3/16"
894
0' - 2 1/8"
54
05 (5 ft.)
4' - 11 7/16"
1510
0' - 6 1/8"
156
3' - 11 3/16"
1199
0' - 2 1/8"
54
06 (6 ft.)
5' - 11 7/16"
1815
0' - 6 1/8"
156
4' - 11 3/16"
1504
0' - 2 1/8"
54
07 (7 ft.)
6' - 11 7/16"
2119
0' - 6 1/8"
156
5' - 11 3/16"
1808
0' - 2 1/8"
54
08 (8 ft.)
7' - 11 7/16"
2424
0' - 6 1/8"
156
6' - 11 3/16"
2113
0' - 2 1/8"
54
1. 1/4-20 Threaded rod to structure (supplied and installed by others).
2. 1/4-20 Coupler hardware (supplied and installed by others).
3. 1 ” 1/4-20 Stud (by Selux).
4. Ø5/16” [Ø7mm] mounting hole.
5. 1/2” wide alum. angle runs the entire length of fixture to block view into
plenum area from below fixture.
6. Suitable for Decoustic® ceiling panel installations with panels up to 2” thick
(supplied and installed by others). Other ceiling systems possible, please
consult factory. Decoustic® is a registered trademark of Decoustics Ltd.
Corporation.
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 4 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
T-Bar Mounting (TB)
T-Bar with Stud Mounting (TBS)
T-Bar with Suspension Clips (TB)
T-Bar with 1/4-20 Stud (TBS)
(9/16” or 15/16” grid)
(9/16” or 15/16” grid)
1. Support wire to structure (supplied and installed by others).
2. Spring steel suspension clips located approximately every 4 ft.
(supplied by Selux).
3. 9/16” T-bar grid (shown as ref.)
3a. 15/16” T-bar grid (shown as ref.)
4. 1/4-20 Threaded rod to structure (supplied and installed by others).
5. 1/4-20 Coupler hardware (supplied and installed by others).
6. 1” 1/4-20 Stud (by Selux).
7. Ø5/16” [Ø7mm] mounting hole.
T-Bar (TB & TBS) and Perimeter Mount (PMT) - Dimensions
Nominal
Length
“A”
O.A.L. with Flange
Feet/Inch
MM
“A1”
O.A.L. without Flange
Feet/Inch
MM
“B”
End Suspensions
Feet/Inch
MM
“BB” (TB mtg.)
Suspension
Clips
Quantity
** “C” (Ref.)
Mid. Suspension
Feet/Inch
MM
“D”
Feed Location
Feet/Inch
“E”
Grid Spacing
MM
Feet
“F”
Wall Angle
Feet/Inch
MM
*02 (2 ft.)
1' - 11 13/16"
605
1' - 10 15/16"
583
0' - 1 5/8"
41
4x
1' - 2"
355
0' - 1 1/8"
28
2’ Center to Center
1' - 11 13/16"
605
*04 (4 ft.)
3' - 11 13/16"
1215
3' - 10 15/16"
1193
0' - 6 1/8"
156
6x
2' - 10 11/16"
882
0' - 2 1/8"
54
4’ Center to Center
3' - 11 13/16"
1215
*05 (5 ft.)
4' - 11 13/16"
1519
4' - 10 15/16"
1497
0' - 6 1/8"
156
6x
3' - 10 11/16"
1187
0' - 2 1/8"
54
5’ Center to Center
4' - 11 13/16"
1519
*06 (6 ft.)
5' - 11 7/8"
1825
5' - 11"
1803
0' - 6 1/8"
156
6x
4' - 10 3/4"
1492
0' - 2 1/8"
54
6’ Center to Center
5' - 11 7/8"
1825
*08 (8 ft.)
7' - 11 13/16"
2434
7' - 10 15/16"
2412
0' - 6 1/8"
156
8x
6' - 10 11/16"
2101
0' - 2 1/8"
54
8’ Center to Center
7' - 11 13/16"
2434
**Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
*For other lengths consult factory
Perimeter Mounting T-Bar Length (PMT)
Perimeter Mount T-Bar Length (PMT)
(Recessed Wall Mounting)
8. S
teel Wall Bracket with provision for 1/4-20 fasteners
(hardware to code by others).
9. 2” 1/4-20 Stud (by Selux).
10. 1/2” x 1” Alum. wall angle allows a gap between flange
and wall to create shadow line allowing for uneveness
of wall. Provision for #10 screws supplied approximately
every 2 ft. (hardware to code by others).
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 5 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
Rotating Crossbar Mounting (RC)
1/4-20 Threaded Stud Mounting (TS)
Rotating Crossbars (RC)
1/4-20 Threaded Stud (TS)
(1/4” to 2” thick ceiling)
(1” Threaded Stud)
1. Rotating Crossbar intended for inaccessible ceilings, adjustable for ceiling
thickness of 1/4” to 2”.
2. 1/4-20 Threaded rod to structure (supplied and installed by others).
3. 1/4-20 Coupler hardware (supplied and installed by others).
4. 1” 1/4-20 Stud (by Selux).
5. Ø5/16” [Ø7mm] mounting hole.
Rotating Crossbar (RC), Threaded Stud (TS), and Perimeter Mountings (PM) - Dimensions
Nominal
Length
“A”
O.A.L. with Flange
“A1”
O.A.L. without Flange
“B”
End Suspensions
** “C” (Ref.)
Mid. Suspension
“D”
Feed Location
“E”
Wall Angle
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
Feet/Inch
MM
*01 (1 ft.)
1' - 1 3/16"
335
1' - 5/16"
313
0' - 1 5/8"
41
0' - 9 1/8"
231
0' - 9/16"
15
1' - 1 3/16"
335
605
02 (2 ft.)
1' - 11 13/16"
605
1' - 10 15/16"
583
0' - 4 1/2"
114
1' - 2"
355
0' - 1 1/8"
28
1' - 11 13/16"
03 (3 ft.)
3' - 1 3/16"
945
3' - 5/16"
923
0' - 6 1/8"
156
2' - 1/8"
612
0' - 2 1/8"
54
3' - 1 3/16"
945
04 (4 ft.)
3' - 11 13/16"
1215
3' - 10 15/16"
1193
0' - 6 1/8"
156
2' - 10 11/16"
882
0' - 2 1/8"
54
3' - 11 13/16"
1215
05 (5 ft.)
4' - 11 13/16"
1519
4' - 10 15/16"
1497
0' - 6 1/8"
156
3' - 10 11/16"
1187
0' - 2 1/8"
54
4' - 11 13/16"
1519
06 (6 ft.)
5' - 11 7/8"
1825
5' - 11"
1803
0' - 6 1/8"
156
4' - 10 3/4"
1492
0' - 2 1/8"
54
5' - 11 7/8"
1825
07 (7 ft.)
6' - 11 13/16"
2129
6' - 10 15/16"
2107
0' - 6 1/8"
156
5' - 10 11/16"
1796
0' - 2 1/8"
54
6' - 11 13/16"
2129
08 (8 ft.)
7' - 11 13/16"
2434
7' - 10 15/16"
2412
0' - 6 1/8"
156
6' - 10 11/16"
2101
0' - 2 1/8"
54
7' - 11 13/16"
2434
*RC mounting, consult factory for lengths under 2’
Perimeter Mounting (PM)
**Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Perimeter Mount (PM)
(Recessed Wall Mounting)
6. Steel Wall Bracket with provision for 1/4-20 fasteners (hardware to code by others).
7. 2” 1/4-20 Stud (by Selux).
8. 1/2” x 1” Alum. wall angle allows a gap between flange and
wall to create shadow line allowing for uneveness of wall.
Provision for #10 screws supplied approximately every 2 ft.
(hardware to code by others).
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 6 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
Standard Drivers for 1’ Luminaires:
Standard Drivers for 2’ fixtures and longer:
Non-dimming driver
1’ luminaires are supplied with standard non-dimming driver.
0-10V linear dimming
Fixtures supplied with drivers capability of either normal switched
operation or 0-10V dimming for linear dimming curve. Fixtures ship with
the dimming leads capped, for dimming operation un-cap the wires.
Minimum dimming level down to 1%. Max. inrush current per driver
30mA²s and 0-10V control current Max. 2mA per driver.
Optional eldoLED Dimming Drivers:
Optional LUTRON Dimming Drivers:
eldoLED 0-10V linear dimming (DM)
Luminaires supplied with SOLOdrive 0-10V dimming driver for linear
dimming curve. Minimum dimming level preset at factory to 1%. For “dim
to dark” (down to 0.1%), please consult factory. Max. inrush current per
driver 30mA²s and 0-10V control current Max. 2mA per driver.
LUTRON 2-wire dimming (DC2)
Luminaires supplied with A-series 2-wire dimming driver programmed
for Constant Current Reduction (CCR). For Pulse Width Modulation
(PWM) dimming, please consult factory. Minimum dimming level down
to 1%. Inrush current per driver < 2A.
eldoLED 0-10V logarithmic dimming (DML)
Luminaires supplied with SOLOdrive 0-10V dimming driver for logarithmic
dimming curve. Minimum dimming level preset at factory to 1%. For “dim
to dark” (down to 0.1%), please consult factory. Max. inrush current per
driver 30mA²s and 0-10V control current Max. 2mA per driver.
LUTRON 3-wire dimming (DC3)
Luminaires supplied with A-series 3-wire dimming driver programmed
for Constant Current Reduction (CCR). For Pulse Width Modulation
(PWM) dimming, please consult factory. Minimum dimming level down
to 1%. Inrush current per driver < 2A.
eldoLED DALI dimming (DMD)
Luminaires supplied with SOLOdrive DALI dimming driver for logarithmic
dimming curve. Minimum dimming level preset at factory to 1%. For “dim
to dark” (down to 0.1%), please consult factory. Max. inrush current per
driver 30mA²s.
LUTRON EcoSystem dimming (DCE)
Luminaires supplied with A-series EcoSystem (4 wire, digital link) dimming driver programmed for Constant Current Reduction (CCR). For
Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%. Inrush current per driver < 2A.
*For control recommendation for eldoLED drivers, please contact eldoLED.
**For control recommendation and system layout for LUTRON drivers,
please contact LUTRON.
Driver Quantity
1 ft.
2 ft.
3 ft.
4 ft.
5 ft.
6 ft.
7 ft.
8 ft.
9 ft.
10 ft.
11 ft.
12 ft.
RUN
Standard Driver and
Optional DML & DMD drivers
1
1
1
1
1
1
2
2
2
2
3
3
Approximately 1 driver
per 4 ft.
Optional DC2, DC3, & DCE drivers
1
1
1
1
1
2
2
2
3
3
3
3
Consult Factory
Wiring Diagrams
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 7 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
Fuse (FS) - Fusing, luminaires supplied with a in-line fuse located on the
hot wire for each feed. (supplied with an 8A slow burn fuse).
Damp Location (DL) - Luminaires are suitable for use in damp
location(s). Examples of such locations include protected areas under
canopies, marquees, roofed porches, and similar locations where the
fixture(s) are protected from direct contact with rain, snow, or excessive
moisture (such as ocean spray). Interior locations include areas subject
to moderate degrees of moisture, such as basements and certain barns
and cold storage buildings. All solder points on LED boards are conformal
coated. The phosphor layer of the LEDs is free of coating to avoid hazing.
EMN (Emergency Battery Pack)* - Emergency battery pack is available starting at the 4’ nominal length and up in 2’ nominal sections. The
battery pack is housed in a box on the top of the luminaire and is fully
accessible from below the ceiling.
- F or individual luminaires, the lit section will be located on the feed end
of the fixture. If a different location is needed please consult the factory.
Separate Switching (SS) - Luminaires available with separately
switched 4’ (nominal) sections starting at 7’ and up. Luminaire is intended to be wired to the same panel/breaker (not intended for Emergency use).
- To specify this option, the number of separately switched sections and
locations of these sections must be provided at time of order.
* If the project requires different separate switching than outlined above
please consult the factory.
EMN Model #
Input
Operation Time
Lumen Output
CCT
Shielding
IOTA ILB-2412
2.5W Max.
90 Minutes
*966 lm
**4000K
LW
*Lumen output is fixed and the same for all light engines
**See page 11 for CCT multiplier
- For Runs, please specify location of lit section (in 2’ nominal sections).
*Luminaires with EMN option are Non-IC-rated
Emergency Circuit (EC) - Luminaires with EC option compliant to UL
924 listed emergency luminaire. EC luminaires are intended to be wired to
separate panels/breakers for emergency use.
1’-5”(432mm)
2 3/4”(70mm)
- For 1’ to 6’ nominal luminaires, the entire fixture is wired for
operation on emergency circuit.
- For 7’ and up nominal luminaires, the first 4’ nominal length is
wired for operation by a separate EM circuit by default to meet
the required “Life Safety Code” (NFPA 101).
**If a different configuration is needed please consult the factory.
Flex Whip - standard for recessed fixtures
Joiner System - standard for Runs and Configurations
90° Elbow on top of the housing (7/8" feed hole)
3/8" flexible metal conduit (6' long)
6" leads
Straight fitting
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 8 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
Standard Recessed (L10) shapes/configurations:
Listed below are the minimum lengths and details for standard shapes.
These standard shapes can be combined with each other and/or the
standard luminaire lengths, ensuring full even illumination. If you have any
questions, please consult the factory.
The minimum standard lengths for “L” shapes:
- IL90 or V90 open shapes is 4’ x 4’ nominal (example: leg, 90, leg)
- IL90 or V90 closed shapes is 6’ x 6’ nominal (example: 90, leg, 90)
(E xception is that the IL90 & V90’s can be joined directly to provide
a 4’ x 4’ nominal shape)
The minimum standard lengths for “T” & “X” shapes:
- IT90 = 4’ nominal on the short leg and 8’ nominal on the long side
- IX90 = 8’ nominal for either direction
Project Specific Recessed (L10) shapes/configurations:
Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements.
Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.
Recessed (L10) Lit Corner and Section - Dimensions
IL90
V90
Feet/Inch
MM
“A” Housing (Outside)
2' - 2 1/16"
662
“A1” Housing (Inside)
1' - 10 1/8"
562
IT90
Feet/Inch
MM
“B” Housing (Outside)
2' - 3 1/2"
698
“B1” Housing (Inside)
1' - 11 1/2"
597
“C” Housing (Inside)
IX90
Feet/Inch
MM
2' - 2 1/16"
662
* “C1” Ref.
2' - 1/8"
612
“D” Housing
4' - 3/16"
1224
* “D1” Ref.
2' - 1/8"
612
“E” Housing
* “E1” Ref.
Feet/Inch
MM
4' - 3/16"
1224
2' - 1/8"
612
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 9 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
Standard Recessed (L1R1/2) shapes/configurations:
Listed below are the minimum lengths and details for standard shapes.
These standard shapes can be combined with each other and/or the
standard luminaire lengths, ensuring full even illumination. If you have any
questions please consult the factory.
The minimum standard lengths for “T” & “X” shapes:
- IT90 = 4’ nominal on the short leg and 8’ nominal on the long side
- IX90 = 8’ nominal for either direction
The minimum standard lengths for “L” shapes:
- IL90 or V90 open shapes is 4’ x 4’ nominal (example, leg, 90, leg)
- IL90 or V90 closed shapes is 6’ x 6’ nominal (example, 90, leg, 90)
(E xception is that the IL90 & V90’s can be joined directly to provide
a 4’ x 4’ nominal shape)
Project Specific Recessed (L1R1/2) shapes/configurations:
Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements.
Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.
Recessed (L1R1/R2) Lit Corner and Section - Dimensions
IL90
V90
Feet/Inch
MM
“A” w/Flange (Outside)
2' - 2 1/2"
673
“A1” Housing (Outside)
2' - 2 1/16"
662
“B” w/Flange (Inside)
1' - 9 11/16"
551
“B1” Housing (Inside)
1' - 10 1/8"
562
IT90
Feet/Inch
MM
“C” Housing (Inside)
2' - 3 1/2"
698
“C1” Housing (Outside)
1' - 11 1/2"
597
Feet/Inch
IX90
MM
Feet/Inch
MM
“F” Housing
4' - 3/16"
1224
* “F1” Ref.
2' - 1/8"
612
“D” w/Flange
2' - 2 1/2"
673
“D1” Housing
2' - 2 1/16"
662
* “D2” Ref.
2' - 1/8"
612
“E” Housing
2' - 1/8"
612
* “E1” Ref.
4' - 3/16"
1224
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 10 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
LED Downlight
LED Downlight Ordering Chart
Quantity
X Number of Downlights
Aperture Shape
R Round
S Square
Wattage
9 9W
CCT
3 3000K
Performance
8 80 CRI, R9 >0. 590 lumens, CBCP 3260cd.
9 95 CRI, R9 95. 490 lumens, CBCP 2700cd.
Ex: 1R938 = 1 Downlight, Round aperture, 9W, 3000K, 80 CRI
Length – 1’ (305mm) section with 1 LED lamp centered. Standard configuration is at the start or end of a run. For other configurations, please
consult the factory.
LED Light Engine – 9W, 3000K SORAA MR16 GU5.3 base lamp, with 25°
beam angle. 80CRI (R9 >0) or 95CRI (R9 =95) available.
Dimming – MR16 LED lamp uses LightTech LET60 electronic dimming
driver, 120V only, separately wired. For dimming compatibility, please see
SORAA’s website: http://www.soraa.com/resources/compatibility
Adjustability - +/- 25º tilt with 360º rotation for Round, 90° rotation for
Square.
Lens – Removable frosted glass lens sits in housing aperture, giving a
smooth, clean finish when downlight is off.
Warranty – Supplied SORAA lamp is not covered by the Selux LED
Luminaire Warranty. Replacement lamps should be suitable for enclosed
luminaires, and rated for 90°C.
1x Downlight
(Round shown)
2x Downlight
(Square shown)
Minimum luminaire length for 1x Downlight is 2’
Minimum luminaire length for 2x Downlight is 3’
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 11 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2
M100
LED Recessed
Photometry
LW Optics / 34W LED / 4000K CCT
1029
Link to photometry (IES & PDF files)
772
515
257
Catalog #: L10-1A35-40-LW-04-120
Report #: 747916
Delievered Lumens: 2900
Input Watts: 34W
Efficacy: 85
Power Factor: 0.994
Total Harmonic Distortion: 5.07
CCT: 3950K
CRI: 83.9
Max Candela: 1029 @ 2.5° from Vertical
Spacing Criterion (0-180): 1.28
Spacing Criterion (90-270): 1.26
Spacing Criterion (Diagonal): 1.38
CCT Multiplier
1
Maximum Candela = 1029.4 Located At Horizontal Angle = 0, Vertical Angle = 2.5
# 1 - Vertical Plane Through Horizontal Angles (90 - 270)
# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
Light Engine Multiplier
4000K
1.000
Engine
Lumens
3500K
0.936
1A35
1.00
1.00
3000K
0.945
1A30
0.88
0.86
2700K
0.923
CCT multipliers apply to the photometry,
IES files, and per foot values listed on
page one (light engine).
2
Watts
1A25
0.74
0.71
1A20
0.60
0.58
Light engine multiplier supplied for per foot
values listed on page one (light engine).
Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not
alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Page 12 of 12
(Rev. 01/2015)
M100LED Recessed_v1.2