1. business and industrial
2. chemicals industry
3. plastics and polymers

Water treatment services
product catalog
E DDINGTON
I N D U S T R I ES
Sample cooler
Product data sheet
custom work
N
EDDINGTO N
I N DU ST RI E S
Sample coolers are a safe method of withdrawing water from
boilers, steam lines or tanks containing chemicals and for
cooling the withdrawn liquid for subsequent chemical analysis.
This Rugged Counter Flow Heat Exchanger is easy to install.
The inner coil uses 316 stainless steel and is one-piece
construction.
Removable coil samples coolers are also available.
Made in the USA.
Specifications
Shell: Carbon steel or type 316 SS
End caps: Carbon steel or type 316 SS
¼” NPT adapters: 316 Stainless Steel
Coil: Continuous coil of type 316 stainless steel
Max coil pressure: 2500 psi
Max shell pressure: 250 psi
Overall length: 13 5/8”
Diameter of shell: 3 ½”
Mounting: 3” pipe clamp
Cooling water fittings: Inlet & outlet, 3/8” NPT steel (female)
Weight: 13 lbs.
Material
PAGE 2
www.eddington.net
Eddington Industries, LLC
Pressure rating
Model
Coil
Shell
Coil
Shell
ESC-CS
316 SS
Steel
2500 psi
250 psi
ESC-SS
316 SS
316 SS
2500 psi
250 psi
Eddington Industries, LLC
www.eddington.net
PAGE 3
Injection Quills
product data sheet
Corporation Stop and Nozzle Assemblies
Product data sheet
N
EDDINGTO N
I N DU ST RI E S
Injection quills are designed to ensure a more uniform and rapid
dispersal of injection chemicals into the center stream of a process
pipeline. This prevents corrosive liquids from clinging to the side of
the pipe.
Injection quills are available in a variety of materials and pressure
ranges as shown on the chart below. Pressure and temperature are
dependent on the material of construction and vary from 150 and
3000 psi and 100 °F (37 °C) and 500 °F (260 °C).
Features
Lead free (LF) available
Features
•Protection chain to prevent the Nozzle Assembly from being completely withdrawn before Corporation
Stop is closed and is a safety feature to protect against back pressure
•Operating pressures to 150 psi
•Quill available in: Corrosion-resistant CPVC, 316 Stainless Steel and Alloy 20
•Corporation Stop (brass only) available with ¾” or 1” process connections
•Quill connection ½” female all models
•Made in the USA
Model
Material
type
Pressure
Temperature
(max)
Side (D)
CS-75-PVC
CS-100-PVC
CPVC
CPVC
125 psi
125 psi
100 ºF (37 ºC)
100 ºF (37 ºC)
CS-100-KY
Kynar
150 psi
CS-75-316
CS-100-316
316 SS
316 SS
CS-75-C20
CS-100-C20
ALLOY 20
ALLOY 20
PAGE 4
Dimensional data
•High pressure, high temperature application
•Simple to use ½”, ¾”, or 1” NPT male process connection and
½”, ¾”, or 1” NPT male chemical inlet connection
•Built-in check valves to prevent backflow of water or steam
through the nozzle and into the chemical line
•Also available without check valves
•Two machined flat surfaces on external portion of nozzle so a
wrench can be used during installation
•Telltale to ensure proper nozzle alignment with process steam for
proper dispersal of injected chemical
•Also available CPVC, Alloy 20 Hastelloy
•Made in the USA
Model
Material of construction
Pressure (max)
Temperature (max)
QC-316-050
316 SS
1000 psi
500 ºF (260 ºC)
QC-KY-050
Kynar
150 psi
200 ºF (93 ºC)
QC-PVC-050
PVC
150 psi
100 ºF (37 ºC)
QC-316-075
316 SS
3000 psi
500 ºF (260 ºC)
QC-KY-075
Kynar
150 psi
200 ºF (93 ºC)
A
B
C
¾” NPT
1” NPT
6
7.5
8½
7 5/8
½ NPT
½ NPT
250 ºF (121 ºC)
1” NPT
7.5
7 5/8
½ NPT
QC-PVC-075
PVC
150 psi
100 ºF (37 ºC)
150 psi
150 psi
250 ºF (121 ºC)
250 ºF (121 ºC)
¾” NPT
1” NPT
6
7.5
8½
7 5/8
½ NPT
½ NPT
QC-316-100
316 SS
3000 psi
500 ºF (260 ºC)
150 psi
150 psi
250 ºF (121 ºC)
250 ºF (121 ºC)
¾” NPT
1” NPT
6
7.5
8½
7 5/8
½ NPT
½ NPT
QC-KY-100
Kynar
150 psi
200 ºF (93 ºC)
QC-PVC-100
PVC
150 psi
100 ºF (37 ºC)
www.eddington.net
Eddington Industries, LLC
Eddington Industries, LLC
www.eddington.net
PAGE 5
Duplex Injection Quills
Product data sheet
N
Retractable injection quill
Product data sheet
EDDINGTO N
I N DU ST RI E S
Injection quills are designed to ensure a more uniform and rapid dispersal of injection chemicals into the
center stream of a process pipeline. This prevents corrosive liquids from clinging to the side of the pipe.
The Duplex Injection Quill allows multiple chemicals to be inserted simultaneously.
Duplex Injection Quills are primarily made from 316 Stainless Steel, but other materials are available. Pressure
and temperature are dependent on the material of construction and vary from 100 °F (37 °C) to 500 °F
(260 °C) at 1000 psi max.
FEATURES
•Insertion length of the inner tube is adjustable, based on where the customer sets the compression fitting
•Hex shaped body allows a wrench to be used during installation
•Made in the USA
Specifications
Chemical Inlet Connections
•¼” MNPT chemical inlet connection
•¼” FNPT chemical inlet connection
•Injection nozzle allows for proper injection into liquid, gas or mixed phase system
•Nozzles can be removed for inspection without system shutdown
•Adjustable quill permits precise positioning of quill in fluid flow and restrains stinger
during insertion/removal
Features
•Available in larger sizes, up to 3” MNPT connection
•Welded safety collar
•Also available CPVC, Alloy 20 Hastelloy
•Made in the USA
Specifications
Process Connection
•¾” or 1” MNPT (standard)
•Quill, ¼” pipe
•Pressure rating: 300 psi
Process Connection
•½” or ¾” MNPT process connection
materials
Material
•316 stainless steel construction
•Other materials available upon request
Model
Application
Wetted Parts: Packing: Process Connection Material of Construction Pressure (max)
Temperature (max)
Model
Type 316 stainless steel
Graphite (maximum temperature - 700 °F)
Process Connection
Material of Construction
Pressure (max) Temperature (max)
QCD-050-316 ¾” MNPT
316 SS
1000 psi
500 ºF (260 ºC)
QR-075-316 ¾” MNPT
316 SS
300 psi
500 ºF (260 ºC)
QCD-075-316 1” MNPT
316 SS
1000 psi
500 ºF (260 ºC)
QR-100-316 1” MNPT
316 SS
300 psi
500 ºF (260 ºC)
PAGE 6
www.eddington.net
Eddington Industries, LLC
Eddington Industries, LLC
www.eddington.net
PAGE 7
Corrosion coupon rack kit
Product data sheet
N
Corrosion coupon rack - series 2000
Product data sheet
EDDINGTO N
I N DU ST RI E S
The corrosion test rack simplifies the
procedure for establishing a corrosion
monitoring program. The kit consists of
¾” or 1” threaded PVC schedule 40 clear
PVC pipe and PVC fittings. The kit is easily
assembled via threaded connections and
an easy to follow instruction guide. This kit
also includes (4) foam covers to minimize
exposure to sunlight.
Four test coupon holders are provided so
that multi-metallic systems can be tested.
An inline 5 or 12 GPM flow regulator is
incorporated into the assembly for
Model #2410-4-F10-KIT shown
maintaining constant water velocity. A
variable in-line flowmeter is also available
as an option for critical measurement of water velocities. An optional clear Y-strainer is available to help
maintain water velocity through the flowmeter and pipe rack.
The corrosion test rack is designed according to ASTM designation D2688-70 which specifies the monitoring
of corrosivity of water in the absence of heat transfer (weight loss methods).
Made in the USA.
Specifications
Construction: Dimensions: ¾” or 1” clear PVC, four station coupon rack
¾” or 1” clear threaded PVC sch. 40 pipe and standard Sch, 80 PVC fittings
24” H x 30” W
Flow regulator: 5 or 10 GPM flow regulator
Coupon holders: 4 coupon holders
Foam covers: 4 foam covers for clear PVC pipe
The corrosion test rack simplifies the procedure for
establishing a corrosion monitoring program. This unit is
preassembled and consists of threaded PVC, black iron
or stainless steel pipe and fittings.
One to six test sites can be provided so that the
multi-metallic systems can be tested. A variable in-line
flow regulator can be incorporated into the assembly
for critical measurement of water velocities. An
optional Y-strainer is available to help maintain water
velocity through the flow meter and pipe rack.
The corrosion test rack is designed according to ASTM
designation D2688-70 which specifies the monitoring
of corrosivity of water in the absence of heat transfer
(weight loss methods).
Options
•1-6 station coupon holders
•Available with or without a mounting board
•High pressure (300 psi) coupon rack available (2600 series)
•Made in the USA
Construction materials available
•Black iron
•CPVC
•PVC
•304 stainless steel
•316 stainless steel
Construction materials available
•Black iron
•CPVC
•PVC
Construction:
Material
2200
¾”
Black iron
2210
1”
Black iron
2400
¾”
PVC
2410
1”
PVC
2500
¾”
Stainless steel
2510
1”
Stainless steel
hreaded PVC, black iron, or
T
type 304 stainless steel pipe and
fittings
Flow meter: 24” H x 30” W
Maximum allowable temperatures @ pressure
80°
280 psi
100°
198 psi
120°
128 psi
>140°
Not recommended
Description
2400-4-F05-kit-clear
¾” 4 station coupon rack kit
Dimensions:
2410-4-F10-kit-clear
1” 4 station coupon rack kit
2700108
Blue-white flow meter model F-41000LN-16, 2-20 GPM,
with 1” FNPT connection
Flow regulator: ¾”- 5 GPM (standard), 1”- 10
GPM (standard)
2700111
Y-strainer, PVC Sch 80
www.eddington.net
Size
Specifications
•304 stainless steel
•316 stainless steel
Part number
PAGE 8
Part number
Eddington Industries, LLC
Eddington Industries, LLC
Optional 2 - 20 GPM flow meter
Y strainer: Optional
www.eddington.net
PAGE 9
TEST COUPON HOLDER
Product data sheet
Coupon By-Pass System – 4000 Series
Product data sheet
N
EDDINGTO N
I N DU ST RI E S
Our standard 4000 Series Corrosion Test
Coupon By-Pass Systems are available with
one to six coupon holders and have both
inlet and outlet isolation ball valves. They are
available in a choice of four materials: Sch 80
PVC, suitable for most applications; CPVC,
for applications requiring moderately
higher temperature; Carbon Steel and
Stainless Steel for high-temperature
applications. The PVC and CPVC bypass
systems are mounted on a high density
polyethylene mounting board.
All piping and valves for the bypass are to be
either ¾ or 1 inch.
Model #4200-2MS-F05 shown
Made in the USA.
Applications
•Cooling Towers
•Chillers
•Boilers
•Heat Exchangers
•Condenser Units
Construction materials available
•Black iron
•CPVC
•PVC
•304 stainless steel
•316 stainless steel
Specifications
Hardware: Nylon, Teflon & stainless steel
OPTIONS
Process connection: ¾” MNPT / 1”MNPT
•Custom configurations and materials
•Back flow check valves
•Flow control valves
•Flow indicators
•Y-strainers
•Test dample valves
Made in the USA
Standard Pipe Plug Assemblies
Carbon Steel or PVC Plugs Stem Material
1. Test specimens must be handled carefully to avoid coating with natural oil from the skin, thread compound
or any similar material.
2. When removed, each specimen is to be carefully disconnected from the holder and then immediately dried
with hot air or by sponging with a paper towel. Do not clean or remove any residue that may be on the
coupon. Insert the specimen in the original envelope or wrap in cellophane. Enclose the test coupon data
card showing company name, locations of the bypass, specimen number, date of installation and date of
removal. Promptly mail to the Eddington Group for analysis.
PAGE 10
www.eddington.net
Eddington Industries, LLC
Eddington Industries, LLC
¾” NPT
PVC
1” NPT
PVC
¾” NPT
Nylon
1” NPT
Nylon
¾” NPT
Teflon
1” NPT
Teflon
¾” NPT
Steel
1” NPT
Steel
www.eddington.net
PAGE 11
Corrosion TEST COUPONS
Product data sheet
N
Retractable coupon holder
Product data sheet
EDDINGTO N
I N DU ST RI E S
Applications
•To provide a basis for estimating service life of process
equipment
•To provide an insight into corrosion mechanics
•To compare resistance of one alloy to another
•As a quality control test for a given heat of alloy
•Pr-weighing and Post-weighing of coupons available
upon request
•Made in the USA
FINISHES
Coupons can be furnished with a variety of finishes depending on
your particular application. Some of the typical finishes available are
defined below.
MILL: Finish as produced from mill
GLASS BEAD: Blasted with fine glass beads to remove
mill scale
Pre-weighing and post-weighing are
available by request
PAGE 12
120 GRIT: Fine finish commonly used in corrosion tests, such as
pitting studies,where smooth surface finish is desired. Finishes up to
600 grit (extremely fine)can be provided
P/N
Material
Hole Size
100100
C10110 steel
3/16”
100200
Copper, CDA110
3/16”
100300
Admiralty brass
3/16”
100400
Galvanized steel
3/16”
100500
Copper Nickel, 90/10
3/16”
100600
Aluminum, 7075-T6
3/16”
100700
Type 304 stainless steel
3/16”
100800
Type 316 stainless steel
3/16”
100900
Mesh bio film
3/16”
101000
Deposition/scale coupon steel C1010
3/16”
www.eddington.net
Simple Retrieval System (up to 300 psi) for removing corrosion test coupons.
Custom Retractable Holder available upon request.
Features
•Standard connection ¾” MNPT
•Available with ½” to 2” NPT threaded or flange connections
•Safety chain
•Welded safety collar
•Made in the USA
Specifications
Process Connection
•¾” or 1” MNPT (standard)
Materials
Wetted Parts: Packing: Eddington Industries, LLC
Eddington Industries, LLC
Type 316 stainless steel
Graphite (maximum temperature - 700 °F)
www.eddington.net
PAGE 13
Manual Glycol Feeder GL50-M-E
product data sheet
N
Glycol Feeder GL-50-E
Product data sheet
EDDINGTO N
I N DU ST RI E S
Specifications
GEAR PUMP: ⅓¾ HP and ½ HP gear pump.
Provides steady and even flow against pressure with an internal
pressure relief bypass valve. Pump suction plumbing includes PVC
drain valve, flexible tubing and Y-strainer. Pump discharge tubing
includes PVC ball valve, brass check valve, brass piping and ¼” NPT
pressure gauge
TANK: 55 gallon polyethylene tank with a PE cover. Tank is fully
supported and restrained by a carbon steel bottom mount stand.
Stand painted with water-based enamel
CONTROL PANEL: The NEMA 4X control panel comes standard
with 115V power cord. The control panel includes 3 position
(hand-off-auto), switch and light for main power, low level light and
15 AMP fuse
LOW LEVEL SWITCH: Polypropylene side entering low level switch
with 10 AMP relay
PRESSURE SWITCH: ¼” NPT pressure switch
PRESSURE RELIEF VALVE: 5-150 PSI
SYSTEM CONNECTION: ¾” Brass FNPT
Features
TANK: 55 gallon polyethylene tank with a PE cover. The Tank is fully supported and restrained by a carbon
steel bottom mount stand. Stand painted with enamel paint
GEAR PUMP: 1/3 HP or 1/2 HP gear pump provides steady and even flow against pressure with an internal
pressure relief bypass valve. Pump suction plumbing includes PVC drain valve, flexible tubing and Y-strainer.
Pump discharge tubing includes brass check valve
ELECTRICAL: 115 Volt AC power cord, 8’ L
PIPING: ½” sch 80 PVC piping and schedule 40 brass piping
DIMENSIONS: 23”L x 23”W x 62”H
SYSTEM CONNECTION: ¾” Brass FNPT, model #GL-50-M-E
Glycol Feeder Options
Part Number
Description
GL-50-E
Comes Standard with Low Level Light
GL-50-E-AA
Comes with Low Level Light and Audible Alarm
GL-50-E-RC
Comes with Low Level Light and Remote Contact Switch
GL-50-2A
Duel Zone Glycol Feeder with: 2 each ½ HP Bronze Rotary Gear Pump (1.5 GPM@ 100 psi)
GL-50-M-E
Manual Feeder with suction and discharge assemblies and 1/3 HP Pump
GL-100-E 100
Gallon Tank with 1⁄2 HP Pump and same options as GL-50-E
GL-Hinged-Lid Standard Lid with a 1/3 Hinged Opening
Made in the USA
PAGE 14
Made in the USA
*Other options available
www.eddington.net
Eddington Industries, LLC
Eddington Industries, LLC
www.eddington.net
PAGE 15
Flow Regulators
Product data sheet
N
Flow Regulators
Product data sheet
EDDINGTO N
I N DU ST RI E S
Applications
•Cooling towers
•Water softeners
•Tankless heaters
•Water filters
•Ground water heat pumps
•Irrigation systems
•Pumps (well and packing water)
•Drinking fountains
•Water purifiers
materials
The Eddington Flow Regulator is designed to deliver a constant volume of water flow over a wide pressure
drop range. The constant flow of water is maintained by the use of the flexible orifice. The flow rate is
maintained to within ± 15% between 15 and 125 psi. The flow rate varies due to manufacturing tolerances
and water temperature. Eddington Industries manufactures flow regulators in various materials such as Nickel
Plated Brass, Type 316 SS, and PVC. Eddington Flow Regulators come in various flow rates and are 3/8”, ½”,
¾”, 1” FNPT, and 1 ¼”, 1 ½”, 2”, 2 ½”, and 3” MNPT and flow rates range from 0.5 to 120 Gallon per minute
(GPM). We also use labels that provide extra-strong protection for harsh environments and conditions. They
are constructed from durable polyester that is water resistant and tear resistant providing durable and secure
protection. All Eddington Flow Regulators are marked with an arrow indicating direction of flow. To ensure
proper operation, always install regulator with the arrow pointed downstream.
Made in the USA
flOW cHaracteristics: fr series valves
flOW (GPm)
5.0
typical ridged restrictor1
4.0
3.0
2
2.0
1.0
•PVC, stainless steel, lead free nickel plated brass
•Sizes: 3/8”, ½”, ¾”, 1”, 1 ¼”, 1 ½”, 2, 2 ½”, 3”, NPT
•Rubber orifice: Buna, Viton, EPDM
•Custom connections, materials and sizes available
•Lead free (LF) available
Model #
(Nickel Plated Brass)
Flow (GPM)
Inlet Connection
Diameter (Inches)
Length (Inches)
FR-038-S
.06 to 1.0
3/8” FNPT
7/8” HEX
1 ¾”
FR-050-S
1.0 to 6.0
½” FNPT
1” HEX
1 15/16”
FR-075-S
1.0 to 11.5
¾” FNPT
1 ¼” HEX
2 9/32”
FR-100-S
1.0 to 30
1” FNPT
1 ½” HEX
2 ¾”
FR-125-S
1.0 to 30
1 ¼” MNPT
1 ¼” PIPE
3”
FR-150-S
1.0 to 30
1 ½” MNPT
1 ½” PIPE
3”
FR-200-S
1.0 to 30
2” MNPT
2” PIPE
3”
FR-250-S
30 to 90
2 ½” MNPT
2 ½” PIPE
4”
FR-300-S
30 to 120
3” MNPT
3” PIPE
4 ½”
3
threshold pressure
10
20
30
40
50
60
70
80
90
100 110 120
Differential Pressure (P.s.i.)
PAGE 16
www.eddington.net
Eddington Industries, LLC
Eddington Industries, LLC
www.eddington.net
PAGE 17
ine.
eeders for shot feeding corrosive
Bromine Feeders
Product data sheet
N
Embrittlement Detector
product data sheet
EDDINGTO N
I N DU ST RI E S
Application
Bromine feeders are a convenient and efficient way to properly feed
solid biocides or other corrosive water treatment chemicals.
These units easily handle ball, stick, tablet and other forms
of bromine.
Vinyl ester resin body tanks are superior to standard steel by-pass
feeders for shot feeding corrosive chemicals.
s.
Features
• Feed rates from 2-1/2 through 230 lb. per day
• Bottom inlet and drain connection
• Top opening with threaded, gasketted closure
• Rated to 150 PSI at 150 F
• Optional PVC piping kits include strainers and all required fittings
• Optional flow indicators in four ranges
• Pressure relief valves and solenoid valves optional
• Made in the USA
Specifications
• Tanks
• Piping kits
• Flow indicators
• Relief valve
• Funnels
hreaded bottom connection
Tanks rated to 150 psi at 150F.
ates
tlet
ap.
Embrittlement Detector for ASTM-D807
Tanks
Vinyl ester resin bodies have two threaded side connections; one
Upper Outlet Upper Outlet threaded bottom connection and one 2-1/2” or 4” top opening with
Feed Rate
Reserve Cap. threaded gasketted closure. Tanks rated to 150 psi at 150F.
(Lbs./Day)
(Lbs.)
Calculated
5-10 Delivery Rates
7
Lower
Upper
Total
Lower Outlet
Upper Outlet
6-12
27Flow Range Outlet
Feed
Outlet Feed
Model
Capacity
Reserve Cap.
Reserve Cap.
Rate
Rate
7-11
25 (GPM)
(Lbs.)
(Lbs.)
(Lbs.)
(Lbs./Day)
(Lbs./Day)
26-36
34
BT-15
15
1-10
N/A
N/A
5-10
7
BT-4030-49 40
1-10
N/A
N/A
6-12
27
261-10
BT-4271-94 42
N/A
N/A
7-11
25
BT-80
1-10
N/A
N/A
26-36
34
82-120 80
5-21
BT-160
160
9900 - E: info@eddington-ind.com
PAGE 18
1-10
Page 12
5-21
The Embrittlement Detector is designed to simulate conditions in a boiler tube seam. By bringing boiler water
in contact with the stressed specimen, the detector determines if the water causes embrittlement cracking.
Carbon steel replacement specimens available.
Features
•Assessing the tendency of industrial boiler waters to cause embrittlement
•Material construction A108 C1018
•Made in the USA
30-49
36-47
41-60
93
www.eddington.net
71-94
82-120
26
Eddington Industries, LLC
Eddington Industries, LLC
www.eddington.net
PAGE 19
steam sampling nozzle
product data sheet
sight gauges
Product data sheet
N
EDDINGTO N
I N DU ST RI E S
“Liquid level Gauge”
Used to calibrate chemical injection systems. The gauge provides a
visual means for checking the contents of a bulk tank and a means
for checking the injection rate of a chemical metering pump. To
gauge is designed to operate in low to medium pressure applications
up to 500 psig.
One minute test
Isolate the chemical in the tank from the gauge. The scale on the left
side is for the gauge volume and the scale on the right will read the
flow rate of the pump; i.e. gallon per Hour (GPH). Keeping the
isolation valve closed and noting the number of marks the fluid
passes in one minute will give the actual chemical pump rate.
gauge features
•Teflon compression ferrule used to isolate the glass tube from
the chamber
•Rugged armored gauge construction protects sight glass from
mechanical impact
•Custom scales for tank volume or other calibrations are available
•Armored frame and polycarbonate shield protect operator
•½” NPT and flange connections standard
•Standard sight tube is 5/8” O.D. glass.
•Made in the USA
gauge specifications
Process Connection
•½” MNPT
features
•Steam sampling nozzles are based on ASTM D-1066-82
•Nondestructive testing, welds, heat treatment, construction, materials and design must be in accordance
with all applicable codes
•The line and sampling nozzle should be the same material of construction
•When single port nozzles cannot be installed in superheated supply tubes, multiport sampling nozzle is
recommended for saturated or super heated steam in larger tubes or lines
•Made in the USA
housing material
C = Zinc Plated Carbon Steel
A = All wetted parts 316 Stainless Steel with 304 Stainless Steel Frame
W = All wetted parts 316 Stainless Steel with Zinc Plated Carbon Steel Frame
PC = All wetted parts PVC with Carbon Steel Frame
PS = All wetted parts PVC with Stainless Steel Frame
sight tube material
5/8” O.D. Standard Glass
*Other sight tube materials available. Consult factory for options
PAGE 20
www.eddington.net
Eddington Industries, LLC
Eddington Industries, LLC
www.eddington.net
PAGE 21
Eddington Industries was established in 1948 by John J. Wynn as
Eddington Tool & Die Company. As industrial output soared in the 1950s,
demand for quality manufacturing propelled Eddington Tool & Die to become
one of leading machine shops in the Philadelphia area. By the mid-60s, the
company doubled the size of its manufacturing plant to meet the demands
of such large corporations such as General Motors and others, however;
as the need for tool and die making declined, and a technology revolution
swept across manufacturing in the United States, the company retooled to
invest in computerized machining centers and software technology to
increase productivity and produce parts for companies across various
industrial sectors.
Our team of engineers and machinists are dedicated to meeting the
highest standards in manufacturing. As a family-run company, we take
particular pride in the quality of our design and work. Through quality control
standards and a dedication to excellence, we strive every day to reach a
new level of quality and value for our customers.
575 Street Road
Bensalem, PA 19020, USA
PHONE: (888) 813-9900
FAX: (215) 244-3250
info@eddington-ind.com
©Copyright 2014 Eddington Industries, LLC All Rights Reserved
Disclaimer: While we make every attempt to keep our information up to date, information in this catalog is subject to change
without notice.