1. home and garden
2. home furnishings
3. lamps and lighting

LG3
Lighting Design · Light and interiors · LG3 solution
The current TRILUX product port-
Contents
Page
folio includes interior luminaires,
exterior luminaires and installation
The visual environment for display use
1
systems for the hospital sector.
Corresponding product infor-
Light and people
2-3
LG3 solutions
4-5
mation can be ordered by fax
and telephone or online at
www.trilux.co.uk.
Solution 1
Interior lighting
Suspended direct/indirect luminaires
6-9
The TRILUX catalogue “Lighting
Design · Light and interiors”
contains the complete range of
Solution 2
Surface-mounted direct/indirect luminaires
10-13
innovative and tried-and-tested
luminaires for interior lighting.
Solution 3
Semi-recessed luminaires
Exterior lighting
In order to consider and document
14-19
Solution 4
Recessed luminaires
20-23
the complex technical and mechanical parameters of various exterior lighting systems, individual
Solution 5
Single point solution
24-25
brochures give detailed information
on these luminaire series.
Solution 6
CAT II upgrade
26-27
Medical technology
Light and installation systems for
Solution 7
light and normal care, for inten-
ASTRON
28-29
Technical details
30-33
CALIS
34-35
sive care areas and clean rooms
are featured in several catalogues
and brochures.
Light planning
The TRILUX lighting design software TX-WIN is an easy-to-operate
tool which enables the correct
and rapid planning on site of
interior lighting installations, street
lighting and the lighting of squares.
References
36
LG3
The visual environment
for display use
Lighting Guide LG3 (1996) and LG3 Addendum (2001) address lighting
for visual function and the wider issue of lighting for visual amenity in environments where display screen equipment is to be used.
LG3 Addendum (2001) should be read in conjunction with LG3 (1996). It
serves to reinforce the importance of visual amenity in lighting installations
through its guidance on acceptable ratios of room surface illuminance to
task illuminance and to update LG3 (1996) by addressing new developments
in display screen and software technology.
Taken from the forward of LG3 (1996)
“There has been a worrying emphasis amongst some designers and users
of the previous edition of this Lighting Guide on selecting luminaires purely
on their ability to reduce screen reflections, without paying due attention to
potential problems that this may cause to the general visual environment
in the area. Because of this greater emphasis has been given to the overall
visual environment in this new lighting guide.”
Key design requirements of LG3 (1996) and LG3 Addendum (2001)
Lighting for visual amenity
• A good luminance balance should be achieved within a space by
considering the finish of its surfaces and the light distribution onto them.
• A balanced luminance pattern should be achieved across the individual
surfaces of a space.
• The general visual impression of gloom, deep shadows and harsh
modeling etc should be avoided.
Lighting for visual function
• Attention should be paid to downlighter-screen-eye geometry
in avoiding distracting reflections.
• Direct glare, particularly problematic in peripheral vision,
should be avoided.
• Satisfactory task illuminance and uniformity should be provided.
• Luminaire surface luminance should be matched with screen
and software characteristics.
This brochure contains a selection of the luminaries offered by TRILUX that
through appropriate design-planning can help to meet the requirements of
LG3 (1996) and LG3 Addendum (2001).
1
LG3
Light and people
Quality criteria and definitions as to lighting have been determined in current
standards – e.g. for the lighting of working facilities in BS EN 12464 –
aimed at the necessary visual performance for the most different visual
tasks.
Substantial quality criteria for this are:
• lighting level,
• glare limitation,
• balanced luminance relations and
• colour rendering quality of the used lamps.
Considerable criteria going beyond the purely visual function such as
• visual perception,
• mood,
• sense of well-being,
• acceptance,
• capability to perform
are not described in European standards, even though these criteria contribute
to lighting quality and to safety and health at the workplace considerably.
It is known that daylight has influenced the human evolution decisively.
Because of the natural day-night-rhythm the human organism has been
adapted to a 24-hour day, the so-called “Circadian Rhythm”.
Parallel to the 24-hour bright-dark-rhythm, endogenous hormones such as
cortisol and melatonin are produced or repressed and body functions such
as vigilance as well as the body temperature are controlled.
A disturbed circadian rhythm, e.g. by too low illuminances on the retina
during the day phase can have a negative influence on the human psyche,
capability to perform and well-being.
Lighting quality depends on the one hand on the light which controls the
visual performance from the anterior brain as “optical part of the visual
pathway” and thus secures the accomplishment of the visual task, and on
the other hand on the light which influences the hormonal functions, i.e.
the non-visual effects by means of the hypophysis as “energetic part of
the visual pathway”.
The Lighting Guide 3 with the addendum 2001 refers to health-relating
aspects of light and to the accordance of statements as to the “health and
safety regulations”.
In addition to the quality criteria of lighting to accomplish the visual task,
other demands focus on the relations of the ceiling and wall illuminances
to the horizontal illuminance. These relations guarantee a bright and
pleasant atmosphere in the user’s field of vision and therefore contribute to
the acceptance and the sense of well-being, thus positively influencing the
psyche.
2
3
LG3
LG3 solutions
Solution 1/suspended direct/indirect luminaires
Suspended direct/indirect luminaires feature pleasing aesthe-
1
tics and offer optimum photometric characteristics to create
low energy lighting solutions that will achieve the light distribution requirements of LG3 in cellular and open plan environments. They are best suited to spaces with floor-to-ceiling
heights of 2.7 m and above.
Solution 2/ surface-mounted direct/indirect luminaires
Surface-mounted direct/indirect luminaires retain the
2
desirable aesthetics and photometric characteristics of
suspended direct/indirect luminaires and in addition can
be used in environments with lower floor-to-ceiling heights.
This luminaire type can achieve the light distribution requirements of LG3 in both cellular and open plan environments
but will achieve a less uniform light pattern across a ceiling
than suspended direct/indirect solutions.
Solution 3/semi-recessed luminaires
Semi-recessed luminaires offer less visual and physical
incursion into a space than both suspended and surfacemounted direct/indirect luminaires. They are easy to install
into ceiling grid arrangements and can be advantageous
when designing lighting for spaces with lower floor-to-ceiling
heights. These luminaires can achieve the light distribution
requirements of LG3 in both cellular and open plan environments but in some instances require favourable room
surface and furniture finishes.
4
3
Solution 4/recessed luminaires
4
Recessed luminaires offer a lighting solution that makes no
physical incursion into a space resulting in clean architectural
lines. This type of luminaire has advantages from both an
aesthetic and an air movement point of view. Recessed
luminaires are easy to install into ceiling grid arrangements
and can be advantageous when designing lighting for
spaces with lower floor-to-ceiling heights. They can achieve
the light distribution requirements of LG3 in both cellular
and open plan environments if room surface and furniture
finishes are favourable. Visually lit elements of recessed
luminaires can also combine with reflected light to give the
perception of a lit ceiling/space irrespective of room and
surface finishes.
Solution 5/single point solution
5
TRILUX has developed a single point solution for open-plan
office spaces with 600 mm square ceiling grids to address
the requirements of LG3. Although correct planning is
essential and the use of this fitting in itself does not ensure
conformity, this luminaire does represent a simple to plan
and cost effective to install single point solution to the
requirements of LG3 tailored to the needs of much of the
UK lighting market.
6
7
Solution 6/CAT II upgrade
Traditional direct distribution recessed luminaires can be
utilised in conjunction with indirect wall-mounted luminaires
to achieve the light distribution requirements of LG3 if the
geometry of a space facilitates it.
Solution 7/ASTRON
The ASTRON range of luminaires unites cutting edge lighting
technology with an innovative form and photometric concept.
The luminaires within this range can be combined harmoniously
or they can be used independently to offer a dynamic and
interesting means of tackling the requirements of LG3.
5
LG3
Solution 1/suspended direct/indirect luminaires
5261 RSX
The 5261 RSX suspended range of luminaires is a technically effective and
aesthetically pleasing lighting solution for open plan and cellular environments
with sufficiently high floor-to-ceiling heights.
Key technical features: Adaptable light distribution characteristics facilitate
appropriate arrangements of the 5261 RSX suspended range of luminaires
meeting the illuminance distribution requirements of LG3 in a wide range of
mounting configurations. Attaching or omitting optical accessories to the
back of the luminaire enables variation of the ratio of direct-indirect light that
is emitted. Optical accessory options include a solid top reflector, perforated
top reflector and prismatic controller. Very high light output ratios (LOR’s)
can be attained by suspended direct/indirect luminaires – the 5261 RSX
suspended range has an LOR of up to 88 %.
Aesthetic features: Suspending the 5261 range in an environment contributes
an elegant point of visual interest with slim, 72 mm deep, contemporary styling.
6
C 0 - C 180
Degree of protection IP 20
Safety class
CIBSE BZ
I
BZ 2/1/BZ1
LOR
Certific.
0.88
ENEC/CE/EMC
Luminaire cat.
B
1
Product description
Suspended luminaire with reflection-intensified, semi-specular parabolic
louvre RSX, for T5 fluorescent lamps.
Example installation:
5261 RSX-L 35 E
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.40
0.8
0.9/0.7
2.25/2.35
80/50/20
Application
Offices, sales areas, showrooms, financial institutions.
Suitable for lighting installations according to CIBSE LG3.
Optical system
Micro-segmented, semi-specular parabolic louvre RSX made of reflectionintensified aluminium with a surface purity of 99,99 %. Fully compliant
to CIBSE LG3, L ≤ 200 cd/m2 at reference angle ¥ ≥ 65°.
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
485
0.69
0.74
0.48
Light distribution
Direct/indirect, with open top, indirect component approx. 45 %. With perforated overhead reflectors: indirect component approx. 15 %. With closed
overhead reflectors: indirect component 0 %.
Luminaire body
Slender and elegant luminaire profile, upper profile arched towards the
ceiling, made of solvent free powder-coated sheet steel, white.
With integrated coupling brackets for non-interrupted continuous lines.
Electrical connection
Luminaires supplied ready for connection. With 5-pole plug-in connection
terminal for mains supply and further wiring for wires up to 2.5 mm2,
including earth connection terminal.
E With electronic control gear in Multi-Lamp technology for T5 lamps in different wattages. ED With dimmable electronic control gear with 1-10 V interface.
7
LG3
T·200 RSX
The T·200 RSX suspended range of luminaires is an aesthetically unique and
technically effective lighting solution for open plan and cellular environments
with sufficiently high floor-to-ceiling heights.
Key technical features: Adaptable light distribution characteristics facilitate
appropriate arrangements of the T·200 RSX range meeting the illuminance
distribution requirements of LG3 in a wide range of mounting configurations.
The T·200 tubular rail mounting system simplifies wiring arrangements
by facilitating the through wiring of luminaire runs. Very high light output
ratios (LOR’s) can be attained by suspended direct/indirect luminaires – the
T·200 RSX suspended range has an LOR of up to 95 %.
Aesthetic features: The T·200 system offers striking contemporary
styling and the potential to observe or create architectural forms through
the physical geometry of the lighting arrangement.
8
C 0 - C 180
Degree of protection IP 20
Safety class
CIBSE BZ
I
BZ 2/0.8/BZ1
LOR
Certific.
0.95
ENEC/CE/EMC
Luminaire cat.
B
1
Product description
Suspended luminaire with reflection-intensified, semi-specular parabolic louvre
RSX, for T5 fluorescent lamps, to be integrated in the T·200 system.
Example installation:
5931 RSX/35 E
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.40
0.8
0.9/0.7
2.25/2.35
80/50/20
Application
For decorative lighting of offices, sales areas, showrooms, financial
institutions. Suitable for lighting installations according to CIBSE LG3.
Optical system
Direct/indirect. Micro-segmented, semi-specular parabolic louvre RSX
made of reflection-intensified aluminium with a surface purity of 99.99 %.
Fully compliant to CIBSE LG3, L ≤ 200 cd/m2 at reference angle ¥ ≥ 65°.
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
493
0.81
0.93
0.57
RSX semi-specular.
Luminaire body
Sheet steel, silver-grey, in slender profile design. With stable and frictionally
integrated end caps in die-cast aluminium which also form a connecting
design element between the subtly rounded side profiles. Integrated fixing
brackets for mounting to rods.
Electrical connection
Luminaires supplied ready for connection. Mains connection is made
within the rods via box terminals up to 1.5 mm2, which are also suitable for
through-wiring to the next unit.
E With electronic control gear.
ED With dimmable electronic control gear with 1-10 V interface.
9
LG3
Solution 2/surface-mounted direct/indirect luminaires
5261 RSX
The 5261 RSX surface-mounted range of luminaires is a technically effective
and aesthetically pleasing lighting solution for open plan and cellular environments with floor-to-ceiling heights of 2.4 m and above.
Technical features: A perforated top reflector controls the indirect lighting
component of the 5261 RSX surface-mounted luminaire allowing for surface
mounting without causing unacceptable ceiling hot spots. Direct/indirect
light distribution characteristics facilitate appropriate arrangements of the
5261 RSX surface-mounted luminaire meeting the illuminance distribution
requirements of LG3. High light output ratios (LOR’s) can be attained by direct/
indirect luminaires – the 5261 RSX surface-mounted range has an LOR of
up to 77 %.
Aesthetic features: Surface mounting the 5261 range reduces its physical
and visual incursion into a space. The 5261 surface range features slim, 90 mm
deep (including single standoff), or 110 mm deep (including double standoff).
10
C 0 - C 180
Degree of protection IP 20
Safety class
CIBSE BZ
I
BZ 2/1/BZ1
LOR
Certific.
0.77
ENEC/CE/EMC
Luminaire cat.
B
1
2
Product description
Surface mounted luminaire with reflection-intensified, semi-specular parabolic
louvre RSX, for T5 flourescent lamps.
Example installation:
5261 RSX-L 35 E + 05261 DG/1200 + 05261 AB
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.05
0.8
0.9/0.5
2.25/2.45
80/50/20
Application
Offices, sales areas, showrooms, financial institutions. Suitable for lighting
installations according to CIBSE LG3.
Optical system
Micro-segmented, semi-specular parabolic louvre RSX made of reflectionintensified aluminium with a surface purity of 99,99 %. Fully compliant to
CIBSE LG3, L ≤ 200 cd/m2 at reference angle ¥ ≥ 65°.
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
461
0.83
0.42
0.45
Light distribution
With perforated overhead reflectors: indirect component approx. 15 %.
With closed overhead reflectors: indirect component 0 %.
Luminaire body
Slender and elegant luminaire profile, upper profile arched towards the ceiling,
made of solvent free powder-coated sheet steel, white. With integrated
coupling brackets for non-interrupted continous lines.
Electrical connection
Luminaires supplied ready for connection. With 5-pole plug-in connection
terminal for mains supply and further wiring for wires up to 2.5 mm2, including
earth connection terminal.
E With electronic control gear in Multi-Lamp technology for T5 lamps in different wattages. ED With dimmable electronic control gear with 1-10 V interface.
11
LG3
E-LINE RPV GH
The E-LINE RPV GH suspended or surface-mounted lighting system is a
technically effective and aesthetically pleasing solution for open plan and
cellular environments.
Technical features: Direct/indirect light distribution characteristics facilitate
appropriate arrangements of the E-LINE RPV-GH surface or suspended
luminaire system meeting the illuminance distribution requirements of LG3
in a wide range of mounting configurations. Rapid installation is facilitated
by factory pre-wiring of the lighting system and its tool-free, clip-together
installation technology.
Aesthetic features: Surface mounting the E-LINE RPV GH lighting system
reduces its physical and visual incursion into a space. Suspending the
E-LINE RPV GH lighting system contributes a point of visual interest into a
space. Both mounting configurations offer the potential to observe or create
architectural forms through the physical geometry of the lighting arrangement.
12
C 0 - C 180
Degree of protection IP 20
Safety class
CIBSE BZ
I
BZ 2/1.5/BZ1
LOR
Certific.
0.62
ENEC/CE/EMC
Luminaire cat.
B
1
2
Product description
Suspended or surface-mounted lighting system with trunking, gear tray,
high reflector and specular parabolic louvre RPV for T8 lamps.
Example installation:
7691/58 E + 07691GH/58 + 07691 RPV/58
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.05
0.8
0.9/0.4
3.0/2.0
80/50/20
Application
Precision assembly, precision mechanics, training rooms, schools and offices.
RPV: recommended for areas with normal DSE usage.
Reflector GH
For gear trays in IP 20.
Radial sheet steel reflector, galvanised, with white polyester coating.
With defined perforation for balanced uplighting. High form, especially
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
552
0.80
0.33
0.48
recommended for combination with louvres RSV, RMV, RPV. Fixed to the
gear tray by means of stainless steel snap fasteners without tools.
Optical system
Highly-specular parabolic louvre RPV, made of highly-specular anodised aluminium with a surface purity of 99.98 %. Luminance limited to L ≤ 200 cd/m2
at reference angle ¥ ≥ 60°, thus corresponding fully to LG3. To be used in
reflectors 0769··· RH, 0769··· GH. Can be hung on the reflector for easy
maintenance.
Electrical connection
Electrical connection is made automatically when the gear tray is attached
to the trunking. Lamp circuit connections can be set to each phase conductor
without tools.
E With electronic control gear.
ED With dimmable electronic control gear with 1-10 V interface.
13
LG3
Solution 3/semi-recessed luminaires
3623 DA
The 3623 DA semi-recessed range of luminaires is a technically effective and
aesthetically pleasing lighting solution for open plan and cellular environments
with tiled or plasterboard ceilings between 2.2-3.0 m AFFL.
Technical features: Highlight of the 3623 DA series is the integrated
plastic profile made of high-quality PMMA. In combination with the perforated
luminaire edge an architectural-decorative ceiling illumination is achieved.
The light distribution of the 3623 DA range facilitates appropriate arrangements
meeting the illuminance distribution requirements of LG3 when the surface
finishes of a room and its furniture are favourable.
Aesthetic features: Irrespective of favourable room surface and furniture
finishes, the 3623 DA semi-recessed luminaire delivers an aesthetic and
amenable lit/visual effect in keeping with the philosophy of LG3. It is physically
unobtrusive, also to air flow.
14
C 0 - C 180
Degree of protection IP 20
Safety class
CIBSE BZ
LOR
Certific.
I
BZ 2
0.71
ENEC/CE/EMC
Luminaire cat.
C
1
3
Product description
Universal recessed and surface-mounted luminaire with reflection-intensified,
semi specular parabolic louvre RSX, with luminous side edges, for three T5
fluorescent lamps 14 W.
Example installation:
3623 RSX-DA/3 x 14
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.0
0.8
0.6/0.6
2.4/2.4
80/50/20
Application
Offices, sales areas and financial institutions. Especially recommended for
areas with normal DSE usage. Universal luminaire system for ceilings with
concealed or exposed grids (600 module) and for ceilings with cut-out
recess openings. Suitable for lighting installations according to CIBSE LG3.
Optical system
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
475
0.81
0.30
0.51
Micro-segmented, semi specular parabolic louvre RSX, made of reflectionintensified aluminium with a surface purity of 99.99 %. With integrated
light-conductor and luminous side edges. Fully compliant to CIBSE LG3,
L ≤ 200 cd/m2 at reference angle ¥ ≥ 65°. Louvre retention by means of
spring-tensioned clips providing earth continuity. Louvre can be lowered and
hung from either side without tools.
Luminaire body
Solvent-free powder-coated sheet steel, white, refined to a particularly
elegant convex design. With flush end caps, inclined by 30° and perfectly
adapted to the luminaire profile.
Electrical connection
Luminaires supplied ready for connection with 3-pole plug-in connection
terminal for wires up to 2.5 mm2, including earth connection terminal.
E With electronic control gear.
ED With dimmable electronic control gear with 1-10 V interface.
15
LG3
3623 T
The 3623 T semi-recessed range of luminaires is a technically effective and
aesthetically pleasing lighting solution for open plan and cellular environments
with tiled or plasterboard ceilings between 2.2-3.0 m AFFL.
Technical features: The 3623 T semi-recessed luminaire range features
refracting side panels that deliver a small amount of light directly onto the
ceiling, which combines with reflected light and the lit appearance of the
luminaire to give the overall sensation of a lit ceiling. The light distribution
of the 3623 T range facilitates appropriate arrangements meeting the
illuminance distribution requirements of LG3 when the surface finishes of a
room and its furniture are favourable.
Aesthetic features: Irrespective of favourable room surface and furniture
finishes, the 3623 T semi-recessed luminaire delivers an aesthetic and
amenable lit/visual effect in keeping with the philosophy of LG3. It is physically
unobtrusive, also to air flow.
16
C 0 - C 180
Degree of protection IP 20
Safety class
I
CIBSE BZ BZ 2/0.75/BZ3
LOR
Certific.
0.72
ENEC/CE/EMC
Luminaire cat.
C
1
3
Product description
Universal recessed and surface-mounted luminaire with reflection-intensified,
Ultra-highly cross-sectional performance louvre (UXP), with luminous side
sections, for three T5 fluorescent lamps 14 W or 24 W.
Example installation:
3623 T UXP-H/14 E
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.0
0.8
0.6/0.6
2.4/2.4
80/50/20
Application
Offices, sales areas and financial institutions. Especially recommended for
areas with normal DSE usage. Universal luminaire system for ceilings with
concealed or exposed grids (600 module) and for ceilings with cut-out
recess openings. Suitable for lighting installations according to CIBSE LG3.
Optical system
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
455
0.89
0.32
0.61
Ultra-highly cross-sectional performance louvre (UXP), with luminous side
sections, made of reflection-intensified aluminium with a surface purity
of 99.99 %. With luminous side sections. Fully compliant to CIBSE LG3,
L ≤ 1000 cd/m2 at reference angle ¥ ≥ 65°. Louvre retention by means
of spring-tensioned clips providing earth continuity. Louvre can be lowered
and hung from either side without tools.
Luminaire body
Solvent-free powder-coated sheet steel, white, refined to a particularly
elegant convex design. With flush end caps, inclined by 30° and perfectly
adapted to the luminaire profile.
Electrical connection
Luminaires supplied ready for connection with 3-pole plug-in connection
terminal for wires up to 2.5 mm2, including earth connection terminal.
E With electronic control gear.
ED With dimmable electronic control gear with 1-10 V interface.
17
LG3
3693 RSX
The 3693 RSX luminaires was designed for use in modern architectural
environments with modular ceiling systems at heights of between 2.2 and
3.0 m AFFL. The elegant decorative perforation appearance on the flanking
side panels lightens the contrast between luminaire and surround.
The louvre section offers a highly efficient photometric platform for the
generation of superb efficiencies and excellent glare limited working environments while still profiting from the homogeneity granted by mat materials.
Due to the flush fitting of the luminaire into the ceiling, in combination with
universal mounting options for both exposed and concealed ceiling grids
and also for gypsum ceilings, the range offers a full compatibility with
architectural requirements while conforming to demands place on the ceiling
void with regard to building services, thanks to the reduced recess depth of
under 60 mm.
18
C 0 - C 180
Degree of protection IP 20
Safety class
I
CIBSE BZ BZ 3/0.75/BZ2
LOR
Certific.
0.68
ENEC/CE/EMC
Luminaire cat.
C
1
3
Product description
Recessed luminaire with reflection-intensified, highly-specular parabolic
louvre RPX, for three T5 fluorescent lamps 14 W.
Example installation:
3693 RSX/14 E LG3
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.0
0.8
0.6/0.6
2.4/2.4
80/50/20
Application
Offices, sales areas and financial institutions. Especially recommended for
areas with normal DSE usage. Universal luminaire system for ceilings with
concealed or exposed grids (600 module) and for ceilings with cut-out
recess openings. Suitable for lighting installations according to CIBSE LG3.
Optical system
Highly-specular parabolic louvre RPX, made of reflection-intensified aluminium
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
555
0.87
0.31
0.50
with a surface purity of 99.99 %. Fully compliant to CIBSE LG3, L ≤ 200 cd/m2
at reference angle ¥ ≥ 65°. Louvre retention by means of spring-tensioned
clips providing earth continuity. Louvre can be lowered and hung from either
side without tools.
Luminaire body
Solvent-free powder-coated sheet steel, white with lateral perforated sides
to improve ceiling illuminance according to CIBSE LG3.
Electrical connection
Luminaires supplied ready for connection with 3-pole plug-in connection
terminal for wires up to 2.5 mm2.
E With electronic control gear (fitted as standard).
Dimmable and emergency versions available on request.
19
LG3
Solution 4/recessed luminaires
1302 RSX
The 1302 RSX recessed range of luminaires is a technically effective
and aesthetically pleasing lighting solution for open plan and cellular
environments with tiled or plasterboard ceilings between 2.2-3.0 m AFFL.
Technical features: The 1302 RSX luminaire features refracting side panels
that present an aesthetically pleasing lit effect, and increase the amount
of light delivered onto the walls of a space. The light distribution of the
1302 RSX range facilitates appropriate arrangements meeting the illuminance
distribution requirements of LG3 when the surface finishes of a room and its
furniture are favourable.
Aesthetic features: Irrespective of favourable room surface and furniture
finishes the 1302 RSX luminaire delivers an amenable lit/visual effect
in keeping with the philosophy of LG3. It presents no physical incursion
into architectural lines and is an elegant lighting solution that improves the
aesthetics and amenability of tiled ceiling environments.
20
C 0 - C 180
Degree of protection IP 20
Safety class
CIBSE BZ
LOR
Certific.
I
BZ 1
0.69
ENEC/CE/EMC
Luminaire cat.
C
1
4
Product description
Recessed luminaire with semi-specular parabolic louvre RSX and linear
refraction elements, for 2, 3 or 4 T5 fluorescent lamps.
Example installation:
1302/224 RSX E
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.0
0.8
0.6/0.6
2.4/2.4
80/50/20
Application
Offices, sales areas and financial institutions. Especially recommended for
workstations equipped with high-brightness TFT-screens. Universal luminaire
system for ceilings with exposed grids (600 module) and for ceilings
with cut-out recess openings. Suitable for lighting installations according
to CIBSE LG3.
Optical system
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
440
0.88
0.30
0.51
Semi-specular parabolic louvre RSX, in combination with internal secondary
reflectors and linear refraction elements. Highly transmissive refraction
elements made of polycarbonate, louvre made of reflection-intensified
aluminium with a surface purity of 99.99 %. Compliant to CIBSE LG3, with
regard to screen classification I and II according to BS EN ISO 29241 Part 6,
i. e. L ≤ 1000 cd/m2 at reference angle ¥ ≥ 65°. Louvre retention by means
of spring-tensioned clips providing earth continuity.
Luminaire body
Solvent-free powder-coated sheet steel, white.
Electrical connection
Luminaires supplied ready for connection. With 3-pole plug-in connection
terminal for wires up to 2.5 mm2, including earth connection terminal.
E With electronic control gear.
21
LG3
1361 PSOW
The 1361 PSOW recessed range of luminaires is a technically effective
and aesthetically pleasing lighting solution for open plan and cellular
environments with tiled or plasterboard ceilings between 2.2-3.0 m AFFL.
Technical features: The 1361 PSOW luminaire features reflecting side panels
that present an aesthetically pleasing lit effect, and increase the amount
of light delivered onto the walls of a space. The light distribution of the
1361 PSOW range facilitates appropriate arrangements meeting the illuminance
distribution requirements of LG3 when the surface finishes of a room and its
furniture are favourable.
Aesthetic features: Irrespective of favourable surface finishes the 1361 PSOW
recessed luminaire delivers an amenable lit/visual effect in keeping with the
philosophy of LG3. It presents no physical incursion into architectural lines
and is an elegant lighting solution that improves the aesthetics and amenability
of tiled ceiling environments.
22
C 0 - C 180
Degree of protection IP 20
Safety class
CIBSE BZ
I
BZ 1/4/BZ2
LOR
Certific.
0.70
ENEC/CE/EMC
Luminaire cat.
C
1
4
Product description
Recessed luminaire with double-reflection system, for 1 compact fluorescent
lamp TC 40 W and TC 55 W. Twin lamp options are available.
Example installation:
1361/1 TC 40 PSOW RSX
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.0
0.8
0.6/0.6
2.4/2.4
80/50/20
Application
Sales areas, showrooms, conference rooms as well as in offices and
financial institutions. Universal luminaire system for ceilings with exposed
grids (600 module) and for ceilings with cut-out recess openings. Suitable
for lighting installations according to CIBSE LG 3.
Primary optics
Louvre fixing, sheet steel, white, with laterally inclined, semi-transmissible
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
442
0.88
0.30
0.54
decorative elements in the upper section. Highly-specular parabolic louvre RPX,
made of reflection-intensified aluminium with a surface purity of 99.98 %.
Louvre retention by means of spring-tensioned clips providing earth continuity.
Secondary diffuser
Double concave-profiled, made of solvent-free powder-coated sheet steel,
with highly-reflective lacquer.
Total optical system
Suited for lighting installations according to LG3.
Fully compliant, L ≤ 1000 cd/m2 above reference angle ¥ ≥ 65°.
Luminaire body
Solvent-free powder-coated sheet steel, white.
Electrical connection
Luminaires supplied ready for connection with 3-pole plug-in connection
terminal for wires up to 2.5 mm2. E With electronic control gear (fitted as
standard). Dimmable and emergency versions available on request.
23
LG3
Solution 5/single point solution
5261 RSX
TRILUX has created a single point lighting solution that is easy to plan,
install, and that is tailored to the most frequently constructed office
environment in the UK – an open plan space in which VCE will be used with
a 600 mm x 600 mm tiled ceiling circa 2.4 m AFFL.
Technical features: The single point solution features a direct/indirect light
distribution optimised by a pre-assembled reflective tile component. Light is
delivered directly onto the ceiling, walls and task surfaces of a space, which
efficiently lights it to the requirements of LG3. Installation is made easy by
the drop-in nature of the luminaire assembly into tiled ceiling arrangements.
The single point solution facilitates meeting the illuminance distribution
requirements of LG3.
Aesthetic features: The TRILUX single point solution is an elegant lighting
solution that improves the aesthetics and amenability of tiled ceiling environments.
24
C 0 - C 180
Degree of protection IP 20
Safety class
CIBSE BZ
LOR
Certific.
I
BZ 1
0.78
ENEC/CE/EMC
Luminaire cat.
B
1
5
Product description
Recessed/suspended luminaire with integrated ceiling plate and semispecular parabolic louvre RSX, for two T5 fluorescent lamps 24 W or 14 W.
Example installation:
5261 RSX/2 x 24 E LG3
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.2 x 2.7
0.75
9.8 x 9.8
0.0
0.8
0.6/0.6
2.4/1.8
80/50/20
Application
Offices, sales areas, showrooms and financial institutions. For ceilings with
exposed grids in module 600. Suitable for lighting installations according to
CIBSE LG3.
Optical system
Semi-specular parabolic louvre RSX, made of reflection-intensified aluminium
with a surface purity of 99.98 %. Fully compliant to CIBSE LG3 L ≤ 200 cd/m2
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
551
0.84
0.32
0.51
above reference angle ¥ ≥ 65° spring-tensioned clips providing earth
continuity. Secondary light component by means of integrated ceiling plate,
therefore suited for lighting installations according to LG3.
Luminaire body
Consisting of a ceiling plate to lay into exposed grid ceiling systems, module
600 mm, and a lumnaire suspended by means of a short pendant rod. Ceiling
plate, made of sheet steel, white. Ceiling plate and luminaire body tightly
screwed by means of short pendant rod, ¶ 10 mm, 55 mm long. Luminaire
body with slim profile, supplied with semi-transmissive overhead reflector,
made of solvent-free powder-coated sheet steel, white. With integrated
plastic end caps.
Electrical connection
Luminaires supplied ready for connection with 3-pole connection terminal
and integrated Wieland plug GST 18/3, connection at the upper side of the
ceiling plate in the ceiling void. E With electronic control gear in Multi-Lamp
technology for T5 lamps in different wattages.
25
LG3
Solution 6/CAT II upgrade
ATRISplus
Traditional direct distribution recessed louvre luminaires such as the ATRISplus
range can be combined with indirect lighting solutions such as the 6052 UWG,
ES 502 or ECOS range to achieve the illuminance distribution requirements
of LG3.
Technical advantages: Existing installations can be retained and visually/
photometrically upgraded by the introduction of indirect lighting elements.
Technical limitations: Light planning using the combination of direct lighting
louver luminaires and indirect luminaires requires favourable room geometry.
Either a space itself must be small enough to facilitate light thrown across
the ceiling from wall mounted luminaires or a space must have favourably
sited columns onto which luminaires can be mounted.
Aesthetic features
Combining direct and indirect lighting in a space produces visual diversity and
holds great potential to create interesting and amenably lit environments.
26
C 0 - C 180
C 0 - C 180
Degree of protection IP 20
Degree of protection IP 20
Safety class
Safety class
I
I
CIBSE BZ
BZ 1
CIBSE BZ
BZ 6
LOR
0.67
LOR
0.52
Certific.
ENEC/CE/EMC
Luminaire cat.
C
Certific.
1
6
ENEC/CE/EMC
Luminaire cat.
F
Product description
Recessed luminaire for modular ceilings 600 x 600 mm with exposed or
concealed ceiling grids, 15 or 24 mm.
Example installation:
ATRISplus M73 RPV 318 K + ES 502 W/TCT 32 E
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.0
0.8
0.6/0.6
2.4/2.4
80/50/20
Application
Offices, sales areas, showrooms and financial institutions. For ceilings with
exposed grids in module 600. Suitable for lighting installations according to
CIBSE LG3.
Optical system
Highly-specular parabolic cross blades and side panels in 99.98 % purity
anodised aluminium. Compliant to CIBSE LG3, with regard to screen classifi-
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
595
0.71
0.51
0.54
cation I and II according to BS EN ISO 29241 Part 6, i. e. L ≤ 1000 cd/m2
at reference angle ¥ ≥ 65°.
Luminaire body
Luminaire body made of white powder-coated, stove-enamelled sheet steel
with a depth of only 83 mm. This allows integration into ceilings with a
ceiling void of only 200 mm. Louvre retention by means of spring-tensioned
clips providing earth continuity. Louvre can be lowered and hung from
either side without tools.
Electrical connection
Luminaires supplied ready for connection, equipped with conventional ballasts.
E With electronic control gear.
27
LG3
Solution 7/ASTRON
ASTRON
The ASTRON range of luminaires presents a flexible, aesthetically innovative
and technically effective lighting solution for all open plan and cellular
environments.
Key technical features: The ASTRON range features cutting edge lighting
materials and technology to achieve a brightness controlled appearance and
high light output characteristics. A key visual element of the range is the
‘refracting wing’. This presents both an aesthetically pleasing point of visual
interest in a space and a means of delivering highly diffuse amenable light
into it.
Aesthetic features: ASTRON is a range of luminaires that can be used
independently or combined harmoniously, due to aesthetic parallels
throughout the range, to present a dynamic and interesting means of tackling
the challenges of a wide range of modern interior environments including
meeting the requirements of LG3.
28
C 0 - C 180
C 0 - C 180
Degree of protection IP 20
Degree of protection IP 20
Safety class
Safety class
I
CIBSE BZ
BZ 5
CIBSE BZ
LOR
0.81
LOR
Certific.
ENEC/CE/EMC
Luminaire cat.
B
I
BZ 4/2.5/BZ5
0.34
Certific.
1
7
ENEC/CE/EMC
Luminaire cat.
B
Product description
ASTRON is a whole new, direct/indirect lighting system with light-focus
modules made of prismatic polycarbonate: a characteristic design element
conceived for designing with light in workplaces.
Example installation:
ASTRON H2 249 + ASTRON W3 142
Room dimensions L x W x H (m)
Height of workplane (m)
Evaluation area (m)
Suspension length (m)
Maintenance factor
Luminaire position x/y (m)
Luminaire spacing x/y (m)
Reflectance ceiling/wall/floor (%)
10.8 x 10.8 x 2.7
0.75
9.8 x 9.8
0.4
0.8
1.8/0.8
3.6/3.07
80/50/20
Application
Offices and financial institutions. Especially recommended for workstations
equipped with TFT screens.
Optical system
Direct/indirect optical system for general lighting, consisting of two symmetrical light-focus modules in polycarbonate with photometrically effective
Task illuminance  (lux)
Uniformity
Relative ceiling illuminance ceiling/task
Relative wall illuminance wall/task
556
0.72
0.98
0.60
interior prismatic structure and integrated semi-transmissible reflectors in
reflection-intensified aluminium. Luminance limited to L ≤ 1000 cd/m2 at
reference angle ¥ ≥ 65°.
Luminaire body
Luminaire body made of extruded aluminium profiles, silver-grey. Luminaire
body and light-focus modules closed at the front plane by end caps.
ASTRON H··· : With integrated 2-point wire suspension for suspension length
of max. 1.50 m, including ceiling fixing units and decorative set elements for
tool-free alignment or continuous height adjustment of the luminaire.
Electrical connection
Luminaires supplied ready for connection.
ASTRON H··· : With central, transparent mains cable 3 x 0.75 mm2
(ED: 5 x 0.75 mm2) and decorative ceiling rose with 3 (5)-pole connection
terminal for wires up to 2.5 mm2, including earth connection terminal.
E With electronic control gear.
ED With dimmable electronic control gear.
29
LG3
Technical details
• Example used
Reference
Lamps
W
5261 RSX-L/28/54 E
1x 28/54
• 5261 RSX-L/35/49/80 E 1x 35/49/80
5261 RSX-L/28 ED
1x 28
5261 RSX-L/35 ED
1x 35
5261 RSX-L/49 ED
1x 49
5261 RSX-L/54 ED
1x 54
5261 RSX-L/80 ED
1x 80
1
Length*
≈ kg
mm
1192 x 225 x72 3.0
1492 x 225 x72 3.9
1192 x 225 x72 3.0
1492 x 225 x72 3.9
1492 x 225 x72 3.9
1192 x 225 x72 3.0
1492 x 225 x72 3.9
*without end caps
Reference
5931
• 5931
5931
5931
RSX/28 E
RSX/35 E
RSX/2x28 E
RSX/2x35 E
Lamps
W
1 x 28
1 x 35
2 x 28
2 x 35
Length
≈ kg
mm
1230 x 232 x 68 3.2
1530 x 232 x 68 3.7
1230 x 232 x 68 3.5
1530 x 232 x 68 4.0
Reference
Lamps
W
5261 RSX-L/28/54 E
1x 28/54
• 5261 RSX-L/35/49/80 E 1x 35/49/80
5261 RSX-L/28 ED
1x 28
5261 RSX-L/35 ED
1x 35
5261 RSX-L/49 ED
1x 49
5261 RSX-L/54 ED
1x 54
5261 RSX-L/80 ED
1x 80
2
Length*
≈ kg
mm
1192 x 225 x 72 3.0
1492 x 225 x 72 3.9
1192 x 225 x 72 3.0
1492 x 225 x 72 3.9
1492 x 225 x 72 3.9
1192 x 225 x 72 3.0
1492 x 225 x 72 3.9
*without end caps
Reference
Gear tray
• 7691/58 E
7691/58 ED
Lamps
1x 58 W
1x 58 W
IP
rating
IP 20
IP 20
Ballast
E
ED
System
rating
55 W
55 W
Reference
Designation
• 07691 GH/58
Perforated high reflector GH
• 07691 RPV/58 Highly-specular parabolic louvre RPV
Reflector accessories
07691 RKH
Reflector end cap
07691 RVH
Reflector connector
Trunking to be ordered separately.
30
≈ kg
1.4
1.6
gear tray
1x 58 W
1x 58 W
1-lamp
1-lamp
Reference
• 3623 RSX-DA/14 E
3623 RSX-DA/14 ED
Reference
• 3623 T
3623 T
3623 T
3623 T
UXP-H/14
UXP-H/14
UXP-H/24
UXP-H/24
E
ED
E
ED
Reference
• 3693 RSX/14 E LG3
Reference
• 1302/224
1302/314
1302/414
1302/324
1302/424
RSX
RSX
RSX
RSX
RSX
E
E
E
E
E
Reference
• 1361/1TC40 PSOW RSX
1361/1TC55 PSOW RSX
Lamps
W
3 x14
3 x14
Module
mm
600/625
600/625
≈ kg
Lamps
W
3 x 14
3 x 14
3 x 24
3 x 24
Module
mm
600/625
600/625
600/625
600/625
≈ kg
Lamps
W
3 x14
Module
mm
600
≈ kg
Lamps
W
2 x 24
3 x 14
4 x 14
3 x 24
4 x 24
Module
mm
600
600
600
600
600
≈ kg
Lamps
W
1x TC-L40
1x TC-L55
Module
mm
600
600
≈ kg
4.3
4.3
3
4.3
4.3
4.3
4.3
4.8
6.1
6.1
6.2
6.1
6.2
4
6.2
6.2
31
LG3
Technical details
Reference
5
• 5261 RSX/2 x 24 E LG3
Reference
6
• ATRISplus
ATRISplus
ATRISplus
ATRISplus
M73
M73
M73
M73
RPV 318 K
RPV 318 E
RPV 418 K
RPV 418 E
Reference
• ES 502 W/TCT32 E
ES 502 W/TCT32 ED
Reference
···UW···
···UW-G···
6052
6052
6052
6052
UW/TCD 18 E
UW/TCD 42 E
UW-G/TCD 18 E
UW-G/TCD 42 E
Reference
ECOS
ECOS
ECOS
ECOS
32
W
W
W
W
2 TCL
2 TCL
2 TCL
2 TCL
36
36
36
36
E 01
E 03
ED 01
ED 03
Lamps
W
2 x 24
Module
mm
600
≈ kg
Lamps
W
3 x18
3 x18
4 x18
4 x18
Module
mm
600
600
600
600
≈ kg
5.2
4.4
4.4
4.5
4.5
Lamps/socket
W
2 xTC-TEL32/GX24q-3
2 xTC-TEL32/GX24q-3
≈ kg
Lamps/socket
W
2 xTC-DEL18/G24q-2
2 xTC-DEL42/G24q-4
2 xTC-DEL18/G24q-2
2 xTC-DEL42/G24q-4
≈ kg
Lamps/socket
W
2 xTC-L36/2G11
2 xTC-L36/2G11
2 xTC-L36/2G11
2 xTC-L36/2G11
≈ kg
2.6
2.6
2.3
2.4
2.2
2.3
3.4
3.4
3.4
3.4
Reference
ASTRON
ASTRON
• ASTRON
ASTRON
H2
H2
H2
H2
Lamps
W
2 x 28
2 x 35
2 x 49
2 x 54
228
235
249
254
Reference
• ASTRON W3 142
Reference
ASTRON W1 136
ASTRON W1 155
ASTRON W1 180
Lamps/socket
W
1xTC-TEL42/GX24q-4
LxLxH
≈ kg
mm
251 x 120 x 291 3.0
Lamps/socket
W
1xTC-L36/2G11
1xTC-L55/2G11
1xTC-L80/2G11
LxLxH
mm
490 x 341 x 71
640 x 341 x 71
640 x 341 x 71
Reference
ASTRON
ASTRON
ASTRON
ASTRON
ASTRON
ASTRON
ASTRON
ASTRON
H1
H1
H1
H1
H1
H1
H1
H1
LxLxH
≈ kg
mm
1202 x 632 x 71 8.1
1502 x 632 x 71 8.8
1502 x 632 x 71 8.8
1502 x 632 x 71 8.1
128
135
149
154
180
249
254
280
Reference
ASTRON S3 455
ASTRON S3 455 EDS
ASTRON S3 480
Lamps
W
1 x 28
1 x 35
1 x 49
1 x 54
1 x 80
2 x 49
2 x 54
2 x 80
7
≈ kg
2.3
2.9
2.9
E
LxLxH
≈ kg
mm
1202 x 325 x 75 4.5
1502 x 325 x 75 5.2
1502 x 325 x 75 5.2
1202 x 325 x 75 4.5
1502 x 325 x 75 5.2
1502 x 325 x 75 5.3
1202 x 325 x 75 4.6
1502 x 325 x 75 5.5
Lamps/socket
W
4 xTC-L55/2G11
4 xTC-L55/2G11
4 xTC-L80/2G11
≈ kg
15.5
15.8
15.7
All products shown are example only of the complete product range.
For accessories, mounting devices etc. please see main catalogue.
33
LG3
CALIS – Computer Aided Light Simulation
“I can’t understand why people are frightened by new ideas.
I’m frightened of old ones.”
John Cage
The targetted deployment of light activates,
Prestigious lighting planning featuring
CALIS represents the TRILUX concept
motivates, offers visual comfort and puts the
architecture-compatible light effects requires
developed to visualise these requirements.
built environment into the right light.
planning competence.
Realised by highly-specialised designers,
CALIS – (Computer Aided Light Simulation)
the program delivers, as stills or animations,
When planning an environment, the concep-
is a state-of-the-art planning tool paving the
the first, 3D-based impressions about
tion of artificial lighting – compatible with
way from a creative light idea to a suitable
the interplay of architecture and light, even
the architectural objectives – is of crucial
technical lighting solution.
during the design stages.
importance.
LG3
References
TRILUX – Competent partner for project solutions
Apart from an extensive standard portfolio of interior luminaires, exterior luminaires and products for the hospital
sector, TRILUX offers competent and expert advise in project
planning.
In close co-operation with building owners and architects,
special solutions for the project-specific requirements as to
design and photometrics are developed. Put us to the test !
36
Lighting Design · Light and interiors
Lighting design · Light and interiors
The complete TRILUX catalogue “Lighting design · Light and
020-GB
interiors”, a standard documentation for all lighting experts,
convinces with clear orientation, precise photometrical and
electrotechnical information and expressive product and
application photos. On 448 pages this catalogue unites the
TRILUX range of high-quality luminaires for interior lighting.
The technical ASTRON brochure gives detailed information
on the modern lighting system for interiors, technologically
based upon TRILUX’ know-how in task area lighting. However,
when it comes to light distribution an mise en scène of built
Lighting Design · Light and architecture
A S T R O N
ASTRON
environments and luminaires, ASTRON offers truly innovative
03/12-GB
solutions.
With the exterior lighting catalogue “Streets. Pathways.
Squares. – Light.” TRILUX offers a comprehensive compendium for all lighting experts. On 177 pages TRILUX presents
A
S
T
R
O
N
luminaires meeting with the most different requirements in
exterior lighting.
Light and installation systems for light and normal care, for
intensive care areas and clean rooms are featured in several
Streets. Pathways. Squares.
Streets. Pathways. Squares. – Light.
catalogues and brochures such as e.g. “Light + technology
041-GB
in the hospital”.
Light.
The TRILUX CD contains everything lighting specialists
require, e.g. electronic product data, photometric luminaire
data as well as several lighting planning and ROI calculation
programs.
The TRILUX virtual portal is located at www.trilux.co.uk
where the latest information on TRILUX and its products can
be obtained around the clock, world-wide. Downloading new
Light + technology in the hospital
software and current data for photometric calculations is
03/20-D-GB
just one of the many possibilities this website has to offer.
Licht + Technik im Krankenhaus
Light + technology in the hospital
All technical data including details of weight and dimensions have been compiled with all
due care. The actual colours of the products correspond to a great extent to the catalogue
reproductions and colour charts. Differences of colour are possible and due to printing
technology. Errors excepted. We reserve the right to make alterations in the interest of
improving our products.
TRILUX-LENZE GmbH + Co KG
Heidestraße · D-59759 Arnsberg
Postfach 19 60 · D-59753 Arnsberg
Tel. +49 2932/3 01-0
Fax +49 2932/3 01-3 75
info@trilux.de
www.trilux.de
04/22-GB 074 163
TRILUX LIGHTING LIMITED
TRILUX HOUSE, Winsford Way
Boreham Interchange
GB-CM2 5PD Essex
Tel. +44 (0) 12 45/46 34 63
Fax +44 (0) 12 45/46 26 46
sales@trilux.co.uk
www.trilux.co.uk