1. No category

2) S125DL
S100DL / S125DL
▪ General Specification
Rated
Voltage
Current
Weight
DC12V
0.405A
0.92Kg
DC24V
0.365A
0.92Kg
AC110V
0.231A
1.31Kg
AC220V
0.116A
1.31Kg
Model
OPERATING MANUAL
LED Steady/Flashing Light with Phone
S125DL
Thank you for purchasing Q.Light product.
Please read this manual carefully before installing this system
Flashes
Color
60-80/Min.
Amber-A
Red-R
Green-G
Blue-B
▪ External View Drawing
for safe and long use of the product.
▪ Signal sound built-in product with long self-life of light source
by employing high-brightness LED and possible to transmit both
visual and auditory signal at same time.
▪ Excellent in diffusing signal light by employing unique
direct-diffusion system.
▪ Possible to select “steady light” or “flashing light” by using
built-in steady/flashing selection switch according to the
purpose of use.
▪ Material : Lens-AS, Body-ABS, Reflector : Heat Resisting ABS
▪ Flashes(Flashing Type) : 60-80/Min.
Main Built-in
Sound
CH
5 Warning
Sounds
ch1
ch2
ch3
ch4
ch5
Fire A-ANG(Wail)
Emergency WA-U(Yelp)
Ambulance PI-PO(High-Low)
Machinery Fault( PI-PI-PI-)
Foam Release Alarm(PI~ Continuous)
105dB
WM 5 Melodies
ch1
ch2
ch3
ch4
ch5
Sweet Home
For Elise
Cuckoo’s Waltz
Piano Sonata
Turkish March
105dB
WA 5 Alarms
ch1
ch2
ch3
ch4
ch5
Beep(Intermittent)
Door Chime
Phone Ring
Machinery Fault(PI.PI.PI.PI.)
Tripping Bead Sound
103dB
ch1
Reproduction of Voice Recording
ch2
3 Channels
ch3
95dB
Type
▪ Volume : Max. 105 dB/1m
▪ Protection Class : IP54
▪ Each model has 5 sound tones built-in. Select a suitable sound
tone for the purpose of use
WS
1) S100DL
▪ General Specification
Model
Rated
Voltage
Current
Weight
DC12V
0.331A
0.91Kg
DC24V
0.340A
0.91Kg
AC110V
0.219A
1.30Kg
AC220V
0.113A
1.30Kg
S100DL
Flashes
Color
60-80/Min.
Amber-A
Red-R
Green-G
Blue-B
WV
3 Voice
Signals
Volume
Sound Tone
▪ External View Drawing
Power line and signal line come out from the product.
Please refer to below wiring diagram for correct connection
of power supply and signal line.
▸ Power Line : UL1015-NO.16(1.25sq) x 2C
400mm
▪ In case of product using AC voltage : Connect the line without
polarity(wire color).
▪ In case of product using DC voltage : Black line is negative(-).
▸ Signal Line : UL1007-NO.22(0.3sq) 400mm
1) Lens Removal
Remove lens by turning it counterclockwise and make sure
steady/flashing selection switch on assembling board.
2) Selecting Steady/Flashing Type
Choose steady light or flashing light by using Steady/Flashing
selection switch(1). “L” mode of the switch is steady type and
“LF” mode is flashing type.
3) Lens Assembling
Assemble the product in reverse order of separating.
▪ This product was manufactured with the structure for indoor use.
Installing in any direction is okay for indoor use.
▪ Outdoor use is limited at a place where no water or very little
water percolates. Mounting also should be done only with
vertical standing shape.
▪ Mount at the place where exists low vibration, low impact, low
moisture and low dust as long as possible.
▪ Refer to below information and drill necessary mounting holes on
profitable part of the product.
(Make sure PCD from external view drawing.)
▪ Fix the product by using nuts(M5-3EA) originally equipped on
mounting bolt on bottom of the product.
▪ If using voltage is seriously higher or lower than rated voltage, it
can reduce the self-life of the product or can cause a problem
on product operating. Make sure the using voltage does not
exceed +/- 5% of the rated voltage.
▪ If lens or body of the product is contaminated by chemicals such
as thinner, benzene, the product can be damaged, discolored
or deformed. Please be careful.
▪ Do not give strong impact to the product. It can be a reason of
wire disconnection or short circuit.
▪ Do not strongly pull the wire out from the product. It can cause a
disorder.
▪ In case of product using AC voltage, do not allow power
This product has a built-in switch(1) on assembling board for
steady/flasing selection. Refer to following drawing and
explanation for right operating.
1) Lens Removal
Remove lens by turning it counterclockwise and make sure
related parts on assembling board.
supply either to common line or to signal line.
▪ Do not allow power to signal line. Must use contact point
which has no power supply.
Situation
Non- Lighting Partly
Abnormal Higher
Sound Output
Feeble Lighting
Bad Sound Quality
Lighting but
Non-Flashing
Double Sound
Tone
Main Cause
LED is Partly Damaged
Supplying Higher Voltage
than Rated Voltage
Supplyinhg Voltage Higher
Than Rated Voltage
Supplyinhg Voltage Lower
Than Rated Voltage
Wrong Operating L/LF
Selection Switch
Problem L/LF Selection
Switch
Short Circuit of Sound
Tone Signal Line
Error on Sound Tone
Selection Switch
Making Sure Using
Voltage
Convert L/LF Selection
Switch
Contact Q.Light or Their
Agent
Making Sure Wiring
Contact Q.Light or Their
Agent
Wrong Wiring
Making Sure Wiring
Problem with Horn
Contact Q.Light or Their
Agent
No power Supply
Making Sure Power Supply
Wrong Wiring
Making Sure Wiring
No Sound
No Lighting/Flashing
No Sound
Solution
Q-LIGHT CO., LTD.
http://www.qlightkr.com
E-mail : qlightkr@qlightkr.com
Seoul Office (Domestic Sales & A/S)
Tel) 02-2679-6152
Ansung BD A-312, 410-13 Sindorim-Dong, Guro-Gu, Seoul
Overseas Marketing Team / Plant
Tel) 055-328-4082 Fax) 055-328-4083
Plant #1 : 178-1 Woogye-Ri, Sangdong-Myun, Kimhae-Si,
KyungNam, Korea
Plant #2 : 417-1 Geumsa-Dong, Geumjung-Gu, Busan