Download Report

DR Graphic recorder - Installation Instruction
Mother Board
DR Graphic Recorder
This Installation Instruction sheet is intended as a guide for replacing or installing hardware and for setting up
functionality in the recorder. Refer to the User manual for detailed operational requirements.
The DR Graphic recorders are designed for ease of assembly with minimal disturbance to the rest of the unit. If unsure,
please return the unit to your supplier for repair or upgrade.
Opening the recorder and removing the internal chassis of the recorder should only be performed under the following
circumstances:
When an item of hardware requires individual replacement.
When an item of hardware is to be retrospectively fitted.
In all other instances it is recommended that the complete unit be returned to an authorized agent or service centre. For
Agency Approved recorders the product needs to be upgraded or repaired by an Authorized Repair facility.
WARNING
HAZARDOUS VOLTAGES
Disconnect all the power, CJCs and IO cabling to the recorder before removing the IO cards chassis or power supply
chassis and attempting any maintenance procedures.
SAFETY TESTS
Upon completion of service procedures detailed in this instruction verify the installation per the installation section of the
product manual.
Failure to comply with these instructions could result in death or serious injury
CAUTION
OBSERVE ANTI-STATIC PRECAUTIONS
Refer to BS EN61340-5-1: 2001. Basic specification. Protection of electrostatic sensitive devices. Full anti-static
precautions MUST be observed when in contact with the electronics of your recorder.
SAVE DATA, SETUPS AND LAYOUTS
Removal of PCBs and battery back-up will result in the loss of all non-volatile data. Ensure all data and set-ups are
saved.
Failure to comply with these instructions may result in product damage.
43-TV-33-203 iss.1 GLO Dec 14 UK
1
Before attempting to repair or upgrade a recorder, it is advisable to clear sufficient work space so components such as
the front panel can be rested on the work surface without getting scratched or damaged.
If adding a new piece of hardware to your recorder please be aware that if you are running Trend Manager PC software
that the “Hardware Wizard” will require updating to accommodate the hardware changes.
Panel Mounting
Mother Board can be removed, replaced or added to the recorder without removing it from its mounting panel. If you
require the recorder to be removed from the panel, loosen the mounting bracket screws and remove the recorder.
Removing the IO Card Chassis front panel
Removal of the IO Card Chassis front panel is necessary for replacement or fitting any of the PC cards. To remove the
IO Card Chassis front panel use the following procedure.
1. Open the door (Bezel side) of the unit by unlocking the latch.
2. There are 7x No.4/40 screws shown in red circle and 2x captive screws shown in green circle in Figure 1. Remove all
the 4/40 screws and loosen the captive screws.
Figure 1
Inside DR Graphic
3. Remove the slanted chassis cover on the back side of the IO card chassis. See Figure 2.
Figure 2
Cabling inside the slant
43-TV-33-203 iss.1 GLO Dec 14 UK
2
4. Lift the IO card chassis from the front side and park it on the bottom stand.
5. Unplug the USB wire from the front side of the IO card chassis.
Figure 3
IO Card chassis
parked on stand
6. Remove all four screws shown by red circle in Figure 4. Also remove one side screw on the other side of the IO card
chassis front panel.
Figure 4
IO cards slot positions
and screws positions
on IO cards chassis
sides
7. Remove all IO cards shown in Figure 5 from Slot A and Slot B.
Figure 5
Inside the IO Cards
Chassis
43-TV-33-203 iss.1 GLO Dec 14 UK
3
8. After removing the IO cards, pull out the old backplane card vertically through the guides on the side of IO card
chassis.
Note: Hold the IO card chassis by one hand and pull out the backplane board by the other hand to make the
removal easier.
Figure 6
Removing the
motherboard
9. Slide the new backplane card back to its vertical position and fit the backplane card 48 pin IO connector firmly into
the 48 pin processor board IO connector. Take care to align the backplane card into the card guide slots in the
chassis.
10. Make sure that jumpers are connected for slot B as per the following table.
Slot B
AI/AO/Pulse
J8 & J9: Link 1 & 2
Alarm/DI/DO
J8 & J9: Link 2 & 3
NOTE: Do not disturb J4 and J5 jumpers in positions 1 & 2 for Slot A. These are for future provision.
43-TV-33-203 iss.1 GLO Dec 14 UK
4
Re-assembling the Unit
After the mother board is replaced; use the following procedure to re-assemble the unit.
11. Reconnect all of the IO cards shown in Figure 7 from Slot A and Slot B.
Figure 7
Slot positions
12. Make sure to secure all the IO cards and backplane card tightly with the earth bracket using M3 X 8 screws from the
side of the IO card chassis as shown in Figure 8.
Figure 8
Screw positions for IO
cards and motherboard
43-TV-33-203 iss.1 GLO Dec 14 UK
5
13. Reconnect the IO card chassis front panel back into its position and fit two screws on the top side using No.4/40
screws. Then fit 2x No.4/40 screws on both the sides of the IO card chassis front panel. See Figure 9.
Figure 9
Reconnecting the IO
cards chassis
14. Lift the IO card chassis; fold back the bottom stand inside and lower the IO card chassis back into the case for
reconnecting the different cables. Connectors of all the cables are polarized; make sure to connect the connectors as
per notch direction. See Figure 10.
15.
Figure 10 – Cables to be connected inside slant chassis plate to the CPU board
43-TV-33-203 iss.1 GLO Dec 14 UK
6
The table below shows the different cables used and where they should be connected.
Sr. No.
Cable Description
Source - Description
1
Relay extension cable – for status of power
relay
Power supply Board to Backplane board (J10)
2
3
4
5
6
7
Touch Screen Extension Cable – for
extending the touch screen connections
from the touch screen to the CPU board
Backlight Cable – For backlight driver
board
LVDS Cable – For LCD data
Speaker cable – For extending the speaker
connections
Earth Braid – For strong ground
connection
6 Pin Power Cable
Touch screen in Bezel to CPU board in case (J5 – Notch
on cable should face EXT SD connector – J8)
Backlight driver board to backlight connector on the CPU
board (J14)
From LCD in bezel to CPU board (J11)
Speaker to speaker connector on the TVDRG2 backplane
board (J6)
From LCD bracket to the IO cards chassis
Power Supply Board to Backplane Board (J10)
16. Connect all the cables as per the information in the above table and Figure 11.
Fig11
Cables to be connected
43-TV-33-203 iss.1 GLO Dec 14 UK
7
17. Replace the slanted chassis plate and fit it back along with the earth braid using 2x No.4/40 screws as shown in
Figure12.
Figure 12
Reconnecting slant
18. Make sure all the screws shown in red and green colour in Figure 13 are connected back.
Figure 13
Reconnecting the IO
19. Reconnect the CJCs, IO cabling and Power cable as required.
20. Close the door.
21. If the recorder has been removed from the panel, secure it back into the panel using the mounting brackets.
Copyrighted Materials. For more information please contact your supplier.
43-TV-33-203 iss.1 GLO Dec 14 UK
8