arXiv:1502.02576v1 [physics.ins

THIRD GENERATION RESIDUAL GAS IONIZATION PROFILE
MONITORS AT FERMILAB*
J.R. Zagel#, M. Alvarez, B. Fellenz, C. Jensen, C. Lundberg, E. McCrory, D. Slimmer, R. ThurmanKeup, D. Tinsley, FNAL, Batavia, IL 60510, USA
Abstract
The latest generation of IPM's installed in the Fermilab
Main Injector and Recycler incorporate a 1 kG permanent
magnet, a newly designed high-gain, rad-tolerant preamp,
and a control grid to moderate the charge that is allowed
to arrive on the anode pick-up strips. The control grid is
intended to select a single Booster batch measurement per
turn. Initially it is being used to allow for a faster turn-on
of a single, high-intensity cycle in either machine. The
expectation is that this will extend the Micro Channel
Plate lifetime, which is the high-cost consumable in the
measurement system. We discuss the new design and data
acquired with this system.
INTRODUCTION
Previous generations of residual gas ionization profile
monitor’s (IPM’s) have been in operation, both at
Fermilab and other laboratories, for many years [1-3]. The
second-generation system applied a fixed permanent
magnetic field, and polarity change to collect electrons to
reduce space charge effects in the measurement [4]. Its
field quality, while sufficient to improve the
measurements, was not quite 1 kG, and required 4 feet of
beam line to accommodate the magnetic unit. Two
primary issues that arise have been the Micro Channel
Plate (MCP) lifetime, and saturation effects of too much
charge required from them. The third generation is
designed to improve on these deficiencies.
WHAT’S NEW
The new system incorporates the improvements added
to the Fermilab Tevatron IPM [5] along with a few new
features.
New Magnet Design
The new magnet is designed using SmCo5 permanent
magnets. This material was chosen to give the highest
residual magnetic field (Br) with the lowest variation in
temperature dependence, at a reasonable cost and
availability. A standard brick is 1" by 2" by 1/2". The
magnet was intended to provide 1 kG in the detector area,
with the return flux half upstream and half downstream,
and shimmed, such that the beam sees a total integrated
field of zero. The magnet is 31.5”L x 14”D with a
minimum aperture of 4.25” to allow for a 4” diameter
beam pipe suitable to both horizontal and vertical planes
in the Main Injector and Recycler. Magnet design,
modeling, and measurement details have been presented
in [6].
MEASUREMENT TIMING
The new system uses a timing module that combines
the function of our Universal Clock Decoder (UCD), and
the VME RF Timing module (VRFT). This module
decodes the lab-wide timing 10 MHz clock (TCLK), the
machine specific, beam synchronous clock (BSYNC), and
a Machine Data (MDAT) Reference System, and outputs
a clock trigger. Utilizing this board, we can generate a
trigger on a specific machine state, and a particular
machine clock cycle that then enables the beam
synchronous clock pulses to gate our ADC’s. The
resolution of this trigger is one 53 MHz bunch. One
sample per turn is generally acquired for a range of turns
specified in the measurement specification. Multiple
samples per turn is also a supported mode of operation.
___________________________________________
* Operated by Fermi Research Alliance, LLC under Contract No. DeAC02-07CH11359 with the United States Department of Energy.
# zagel@fnal.gov
Figure 1: Recycler Vertical Installation
Anode Strip Board
The anode strip pick-up board for both Main Injector
and Recycler is a ceramic circuit board with 120 copper
strips spaced at 0.5mm. The copper occupies 80% of that
pitch with 20% space between strips. All signals are
connected via 20 pin, ceramic mounted, quick release
connectors. A multilayer flexible circuit delivers these
signals to 6 front flange feed through connectors. A
“Flash Test” strip has been added to the bottom of the
arXiv:1502.02901v1 [physics.ins-det] 10 Feb 2015
A pilot study of the novel J-PET plastic
scintillator with 2-(4-styrylphenyl)benzoxazole
as a wavelength shifter
A. Wieczoreka, b , P. Moskala , S. Nied´zwieckia , T. Bednarskia ,
P. Bialasa , E. Czerwi´
nskia , A. Danelc , A. Gajosa , A. Gruntowskia ,
D. Kami´
nskaa , L. Kaplona, b , A. Kochanowskid , G. Korcyla ,
a
J. Kowal , P. Kowalskie , T. Kozika , W. Krzemie´
na , E. Kubicza ,
M. Molendad , M. Palkaa , L. Raczy´
nskie , Z. Rudya , O. Rundela ,
a
a
P. Salabura , N.G. Sharma , M. Silarskia , A. Slomskia ,
J. Smyrskia , A. Strzeleckia , T. Uchaczd , W. Wi´slickie ,
M. Zieli´
nskia , N. Zo´
na
a
Faculty of Physics, Astronomy and Applied Computer Science,
Jagiellonian University
b
Institute of Metallurgy and Materials Science, Polish Academy
of Sciences
c
Institute of Chemistry and Physics, University of Agriculture
d
Faculty of Chemistry, Jagiellonian University
e´
Swierk Computing Centre, National Centre for Nuclear Research
February 11, 2015
Abstract
For the first time a molecule of 2-(4-styrylphenyl)benzoxazole containing benzoxazole and stilbene groups is applied as a scintillator dopant acting as a wavelength shifter. In this article a light yield of the plastic scintillator, prepared from styrene doped with 2 wt% of 2,5-diphenylbenzoxazole
and 0.03 wt% of 2-(4-styrylphenyl)benzoxazole, is determined to be as
large as 60% ± 2% of the anthracene light output. There is a potential
to improve this value in the future by the optimization of the additives
concentrations.
1
Introduction
Scintillators are widely used as detectors of radiation in many fields of science
and industry. For example they are crucial components of apparatus used in
nuclear and particle physics experiments, medical diagnostics modalities as well
as radiation detectors in many sectors of homeland security [1]
Scintillators play an important role in most of the nuclear imaging devices
such as e.g. Positron Emission Tomography device (PET). Though PET is well
1
Monte Carlo Study of a 137Cs calibration field of the China institute
of atomic energy
GAO Fei a,b,*
a
Radiation Metrology Division, China Institute of Atomic Energy, Beijing, 102413, China
b
National Key Laboratory for Metrology and Calibration Techniques, Beijing, 102413, China
Abstract The MCNP code was used to study the characteristics of gamma radiation field with
collimated beam geometry. A close-to-reality simulation model of the facility was used for
calculation air-kerma along the whole range of source-detector-distance (SDD) along the central
beam and air-kerma off-axis beam profiles at two different source-detector-distance (SDD). The
simulation results were tested by the measured results which were acquired in the Radiation
Metrology Center of CIAE. Other characteristics such as the individual contributions of photons
scattered in collimator, floor, walls, mobile platform and other parts of the irradiation halls to the
total air kerma rate on the beam axis were calculated for the purpose of future improvement of
metrological parameters in CIAE. Finally, factors which influence the simulation results were
investigated, including e.g., detector volume effects or source density effects.
Key Words Monte Carlo, MCNP, Simulation, Calibration, Air Kema, Radiation
1 Introduction
Radiation Metrology Division of CIAE obtains many photon sources with different activity
values for calibration, metrological research and design new dosimeters for detection and
measurement of photon-related quantities. With these sources e.g. cesium-137, colbalt-60 and
americium-241, it is possible to obtain air kerma rate from 0.2μGy /h up to 54Gy/h sufficient for
all of commonly used dosimeters.
Irradiation field shapes and scattered photons are the most important criterions for irradiation
halls. So far, the longitudinal and lateral field shapes in air kerma rate were measured by
secondary ionization chambers.
The development of computer technology made it possible to use sophisticated mathematical
models to calculate relative parameters of the irradiation fields. In this study, a MCNP-4C Monte
Carlo code model of cesium-137 irradiation hall was used for beam profiles verification and for
the assessment and analysis of scattered air kerma, which is very important for future
improvement of metrological parameters of photon beams in CIAE .
2 Experiments
For the purpose of routine measurements, the longitudinal profiles in air kerma rate at distances
from 1m to 6.5m from the 137Cs source were measured with a spherical ionization chamber PTW
32002. The transversal beam profiles were measured in a horizontal line perpendicular to the beam
axis at two distances of 1m and 2m from the 137Cs source. For these measurements,an ionization
chamber NE 30c. c. (Nuclear Enterprises ) was used due to its smaller volume (outer diameter is
about 4cm ).
*
Corresponding author:gaofei@ciae.ac.cn
3 Simulations
1
EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCH (CERN)
CERN-PH-EP/2015-006
2015/02/11
arXiv:1502.02702v1 [physics.ins-det] 9 Feb 2015
CMS-EGM-14-001
Performance of photon reconstruction and identification
with the CMS detector
√ in proton-proton collisions at
s = 8 TeV
The CMS Collaboration∗
Abstract
A description is provided of the performance of the CMS detector for photon reconstruction and identification in proton-proton collisions at a centre-of-mass energy of
8 TeV at the CERN LHC. Details are given on the reconstruction of photons from energy deposits in the electromagnetic calorimeter (ECAL) and the extraction of photon
energy estimates. The reconstruction of electron tracks from photons that convert to
electrons in the CMS tracker is also described, as is the optimization of the photon
energy reconstruction and its accurate modelling in simulation, in the analysis of the
Higgs boson decay into two photons. In the barrel section of the ECAL, an energy
resolution of about 1% is achieved for unconverted or late-converting photons from
H → γγ decays. Different photon identification methods are discussed and their corresponding selection efficiencies in data are compared with those found in simulated
events. The measurement of the photon purity is described for one set of photon
identification criteria.
Submitted to the Journal of High Energy Physics
c 2015 CERN for the benefit of the CMS Collaboration. CC-BY-3.0 license
∗ See
Appendix A for the list of collaboration members
EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCH (CERN)
CERN-PH-EP/2015-004
2015/02/11
CMS-EGM-13-001
arXiv:1502.02701v1 [physics.ins-det] 9 Feb 2015
Performance of electron reconstruction and selection
with
√
the CMS detector in proton-proton collisions at s = 8 TeV
The CMS Collaboration∗
Abstract
The performance and strategies used in electron reconstruction and selection at CMS
−1
are presented based on data corresponding
√ to an integrated luminosity of 19.7 fb ,
collected in proton-proton collisions at s = 8 TeV at the CERN LHC. The paper
focuses on prompt isolated electrons with transverse momenta ranging from about
5 to a few 100 GeV. A detailed description is given of the algorithms used to cluster energy in the electromagnetic calorimeter and to reconstruct electron trajectories
in the tracker. The electron momentum is estimated by combining the energy measurement in the calorimeter with the momentum measurement in the tracker. Benchmark selection criteria are presented, and their performances assessed using Z, Υ,
and J/ψ decays into e+ +e− pairs. The spectra of the observables relevant to electron
reconstruction and selection as well as their global efficiencies are well reproduced
by Monte Carlo simulations. The momentum scale is calibrated with an uncertainty
smaller than 0.3%. The momentum resolution for electrons produced in Z boson decays ranges from 1.7 to 4.5%, depending on electron pseudorapidity and energy loss
through bremsstrahlung in the detector material.
Submitted to the Journal of Instrumentation
c 2015 CERN for the benefit of the CMS Collaboration. CC-BY-3.0 license
∗ See
Appendix A for the list of collaboration members
NJL model approach to diquarks and baryons in
quark matter
arXiv:1502.03084v1 [nucl-th] 10 Feb 2015
D. Blaschke
Institute for Theoretical Physics, University of Wroclaw, 50-204; Wroclaw, Poland
Bogoliubov Laboratory for Theoretical Physics, Joint Institute for Nuclear Research,
RU-141980 Dubna, Russia
E-mail: blaschke@ift.uni.wroc.pl
A. Dubinin∗
Institute for Theoretical Physics, University of Wroclaw, 50-204; Wroclaw, Poland
E-mail: aleksandr.dubinin@ift.uni.wroc.pl
D. Zablocki
Institute for Theoretical Physics, University of Wroclaw, 50-204; Wroclaw, Poland
E-mail: dan.zablocki@gmail.com
We describe baryons as quark-diquark bound states at finite temperature and density within the
NJL model for chiral symmetry breaking and restoration in quark matter. Based on a generalized
Beth-Uhlenbeck approach to mesons and diquarks we present in a first step the thermodynamics
of quark-diquark matter which includes the Mott dissociation of diquarks at finite temperature. In
a second step we solve the Bethe-Salpeter equation for the baryon as a quark-diquark bound state
in quark-diquark matter. We obtain a stable, bound baryon even beyond the Mott temperature for
diquark dissociation since the phase space occupation effect (Pauli blocking for quarks and Bose
enhancement for diquarks) in the Bethe-Salpeter kernel for the nucleon approximately cancel so
that the nucleon mass follows the in-medium behaviour of the quark and diquark masses towards
chiral restoration. In this situation the baryon is obtained as a “borromean” three-quark state in
medium because the two-particle state (diquark) is unbound while the three-particle state (baryon)
is bound.
XXII International Baldin Seminar on High Energy Physics Problems,
15-20 September 2014
JINR, Dubna, Russia
∗ Speaker.
c Copyright owned by the author(s) under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike Licence.
http://pos.sissa.it/
A. Dubinin
NJL model for diquarks and baryons
1. Thermodynamics of correlations in quark matter
While numerous works have recently studied the thermodynamics of quark matter on the
mean-field level including the effects of the medium dependence of the order parameters, not so
much is known beyond the mean field, about hadronic correlations and their backreaction to the
structure of the model QCD phase diagram and its thermodynamics. Here we will elaborate on the
generalized Beth-Uhlenbeck form of the equation of state which is systematically extended from
studying mesonic correlations [1] to the inclusion of diquark degrees of freedom [2, 3]. To that end
we will employ a Nambu–Jona-Lasinio-type quark model with fourpoint interactions in mesonic
(quark-antiquark) and diquark (quark-quark) channels. We shall discuss here the importance of the
interplay of the resonant states with the residual non-resonant ones in the continuum of scattering
states. Due to the Levinson theorem both contributions have the tendency to compensate each other
in quark matter above the Mott transition [4], see also [2, 3, 5, 6].
The most intriguing questions will occur when on the basis of this in-medium bosonized effective chiral quark model the next step of the hadronization program nucleon will be performed
and diquarks will be “integrated out” in favor of baryons so that nuclear matter can be described
in the model QCD phase diagram. A possible scheme for introducing baryons as quark-diquark
bound states and integrating out the colored and therefore not asymptotically observable diquark
fields has been suggested by Cahill and collaborators [7, 8, 9, 10]. It was afterwards elaborated by
Reinhardt [11] and developed further by including the solitonic aspects of a field theoretic description of the nucleon [12]. However, the step to describe nucleonic many-body systems on this quark
model basis has not been performed by these authors. Exploratory studies within the framework
of an effective local NJL-type model for the quark-diquark interaction vertex have revealed a first
glimpse at the modification of the nucleon spectral function in the different regions of the model
QCD phase diagram, including chirally restored and color superconducting phases [13]. Again,
the crucial step towards an equation of state for nuclear matter with this microscopic model for
nucleons in the QCD phase diagram has not yet been done.
We will prepare the ground for a Beth-Uhlenbeck description of nuclear matter, to be discussed
in future work. In particular, at zero temperature the structure of a Walecka model for nuclear matter
shall emerge under specified conditions. Earlier work in this direction [14, 15, 16] has demonstrated
this possibility although no unified description of the nuclear-to-quark matter transition has been
possible and the elucidation of physical mechanisms for the very transition between the hadronic
and the quark matter phases of low energy QCD has been spared out. Or study aims at indicating
directions for filling this gap by extending the discussion of the Mott mechanism for the dissociation
of hadronic bound states of quarks within the NJL model description of low-energy QCD which has
been given on the example ot two-particle correlations (mesons and diquarks) in [2] and sketching
steps towards a Beth-Uhlenbeck description of nuclear matter where nucleons are treated as quarkdiquark correlations in quark matter [17].
1.1 Quark matter thermodynamics in the NJL model
We base the approach on the NJL model Lagrangian including vector and diquark interaction
channels besides the standard scalar-pseudoscalar chirally symmetric interaction for the isospin
symmetric case (µu = µd = µ and mu = md = m0 )
2
Mon. Not. R. Astron. Soc. 000, 1–11 (2014)
Printed 11 February 2015
(MN LATEX style file v2.2)
Bringing the Galaxy’s dark halo to life
T.
Piffl1⋆ , Z. Penoyre2 , J. Binney1
1
Rudolf Peierls Centre for Theoretical Physics, Keble Road, Oxford OX1 3NP, UK
Hall, University of Cambridge, Trinity Lane, Cambridge CB2 1TJ, UK
arXiv:1502.02916v1 [astro-ph.GA] 10 Feb 2015
2 Trinity
submitted to MNRAS on 19th January 2015
ABSTRACT
We present a new method to construct fully self-consistent equilibrium models of multicomponent disc galaxies similar to the Milky Way. We define distribution functions for
the stellar disc and dark halo that depend on phase space position only through action
coordinates. We then use an iterative approach to find the corresponding gravitational
potential. We study the adiabatic response of the initially spherical dark halo to the
introduction of the baryonic component and find that the halo flattens in its inner
regions with final minor-major axis ratios q = 0.75 – 0.95. The extent of the flattening
depends on the velocity structure of the halo particles with radially biased models
exhibiting a stronger response. In this latter case, which is according to cosmological
simulations the most likely one, the new density structure resembles a “dark disc”
superimposed on a spherical halo. We discuss the implications of these results for our
recent estimate of the local dark matter density.
The velocity distribution of the dark-matter particles near the Sun is very nonGaussian. All three principal velocity dispersions are boosted as the halo contracts,
and at low velocities a plateau develops in the distribution of vz . For models similar to
a state-of-the-art Galaxy model we find velocity dispersions around 155 km s−1 for vz
and the tangential velocity, vϕ , and 140 – 175 km s−1 for the in-plane radial velocity,
vR , depending on the anisotropy of the model.
Key words: galaxies: kinematics and dynamics
1
INTRODUCTION
It is now generally accepted that most of the rest mass in the
Universe is contained in a type of “dark matter” that is incapable of electromagnetic interactions. Dark matter began to
cluster gravitationally earlier than baryonic matter because
it was decoupled from the cosmic radiation bath, which at
redshifts >
∼ 1000 provided abundant pressure. Hence the formation of a galaxy starts with the accumulation of dark
matter to form the dark halo. When and how baryons accumulated in the gravitational potential wells of dark halos
is ill understood. In the simplest picture, they simply fell in
dissipatively and formed stars near each halo’s centre, but
this picture is inconsistent with the small fraction of baryons
that are now in stars rather than intergalactic gas. Several
lines of evidence indicate that the release of nuclear energy
by early stars strongly attenuated the infall of baryons, thus
increasing the extent to which galaxies are dark-matter dominated.
The least dark-matter dominated galaxies are ones with
luminosities similar to that, L∗, of our Galaxy: dwarf galax⋆
E-mail: tilmann.piffl@physics.ox.ac.uk
c 2014 RAS
ies are very strongly dark-matter dominated and stars play
such a subsidiary role in the most massive dark-matter halos, those of galaxy groups and clusters, that we do not even
recognise these halos as galaxies. Yet even in galaxies such
as ours, it may be argued that the baryons have played a
very subordinate role. Measurements of the optical depth
to microlensing of stars located less than ∼ 10 deg from the
Galactic centre imply that a significant majority of the mass
inside ∼ 3 kpc is concentrated in stars (Binney & Evans
2001; Bissantz et al. 2004). But the majority of the gravitational force that holds the Sun in its orbit comes from
dark matter (e.g. Piffl et al. 2014, hereafter P14), and the
dominance of dark matter increases sharply with increasing distance from the centre. Moreover, in galaxies such as
ours and M33, we have reason to believe that most baryons
accumulated in the potential well of the dark halo quiescently, forming a disc in centrifugal equilibrium (Mo et al.
1998). In our Galaxy, but not in M33, the central portion of
the disc became unstable to the formation of a strong bar,
which then buckled to form the Galaxy’s present bar/bulge
(Combes & Sanders 1981; Raha et al. 1991).
A dark halo will respond to the quiescent accumulation of baryons in a disc by distorting adiabatically: that
arXiv:1502.02838v1 [physics.atom-ph] 10 Feb 2015
Constraints on extra dimensions from precision
molecular spectroscopy
E. J. Salumbides1,2 , A. N. Schellekens3,4,5 , B. Gato-Rivera3,5 ,
and W. Ubachs1
1
Department of Physics and Astronomy, and LaserLaB, VU University, De Boelelaan
1081, 1081 HV Amsterdam, The Netherlands
2
Department of Physics, University of San Carlos, Cebu City 6000, Philippines
3
Nikhef, Science Park 105, 1098 XG Amsterdam, The Netherlands
4
Institute for Mathematics, Astrophysics and Particle Physics, Radboud University,
6500 GL Nijmegen, The Netherlands
5
Instituto de Fisica Fundamental, CSIC, 28006 Madrid, Spain
Abstract.
Accurate investigations of quantum level energies in molecular systems are shown
to provide a test ground to constrain the size of compactified extra dimensions.
This is made possible by the recent progress in precision metrology with ultrastable
lasers on energy levels in neutral molecular hydrogen (H2 , HD and D2 ) and the
+
+
molecular hydrogen ions (H+
2 , HD and D2 ). Comparisons between experiment and
quantum electrodynamics calculations for these molecular systems can be interpreted
in terms of probing large extra dimensions, under which conditions gravity will become
much stronger. Molecules are a probe of space-time geometry at typical distances
where chemical bonds are effective, i.e. at length scales of an ˚
A. Constraints on
compactification radii for extra dimensions are derived within the Arkani-HamedDimopoulos-Dvali framework, while constraints for curvature or brane separation are
derived within the Randall-Sundrum framework. Based on the molecular spectroscopy
of D2 molecules and HD+ ions, the compactification size for seven extra dimensions (in
connection to M-theory defined in 11 dimensions) of equal size is shown to be limited
to R7 < 0.6µm. While limits on compactification sizes of extra dimensions based on
other branches of physics are compared, the prospect of further tightening constraints
from the molecular method is discussed.
PACS numbers: 04.50.-h, 33.20.Lg, 31.30.jf
Submitted to: New J. Phys.
The Hot QCD White Paper:
Exploring the Phases of QCD at RHIC and the LHC
arXiv:1502.02730v1 [nucl-ex] 9 Feb 2015
A White Paper on Future Opportunities in Relativistic Heavy Ion Physics
February 11, 2015
Abstract
The past decade has seen huge advances in experimental measurements made in heavy
ion collisions at the Relativistic Heavy Ion Collider (RHIC) and more recently at the Large
Hadron Collider (LHC). These new data, in combination with theoretical advances from
calculations made in a variety of frameworks, have led to a broad and deep knowledge of the
properties of thermal QCD matter. Increasingly quantitative descriptions of the quark-gluon
plasma (QGP) created in these collisions have established that the QGP is a strongly
coupled liquid with the lowest value of specific viscosity ever measured. However, much
remains to be learned about the precise nature of the initial state from which this liquid
forms, how its properties vary across its phase diagram and how, at a microscopic level, the
collective properties of this liquid emerge from the interactions among the individual quarks
and gluons that must be visible if the liquid is probed with sufficiently high resolution. This
white paper, prepared by the Hot QCD Writing Group as part of the U.S. Long Range Plan
for Nuclear Physics, reviews the recent progress in the field of hot QCD and outlines the
scientific opportunities in the next decade for resolving the outstanding issues in the field.
1
Classical and Quantum Gauged Massless Rarita-Schwinger fields
Stephen L. Adler∗
Institute for Advanced Study, Einstein Drive, Princeton, NJ 08540, USA.
We show that, in contrast to known results in the massive case, a minimally gauged
massless Rarita-Schwinger field yields consistent classical and quantum theories. To simplify
arXiv:1502.02652v1 [hep-th] 9 Feb 2015
the algebra, we study a two component left chiral reduction of the massless theory. We
formulate the classical theory in both Lagrangian and Hamiltonian form for a general nonAbelian gauging, and analyze the constraints and the Rarita-Schwinger gauge invariance of
the action. An explicit wave front calculation for Abelian gauge fields shows that wavelike modes do not propagate with superluminal velocities. The quantized case is studied in
covariant radiation gauge and axial gauge for the Rarita-Schwinger field, by both functional
integral and Dirac bracket methods. The constraints have the form needed to apply the
Faddeev-Popov method for deriving a functional integral in covariant radiation gauge. The
Dirac bracket approach yields consistent Hamilton equations of motion in covariant radiation
gauge, and leads to anticommutation relations with the correct positivity properties in axial
gauge. We note that fermionic gauge transformations are a canonical transformation, but
further details of the transformation between different fermionic gauges are left as an open
problem.
I.
A.
INTRODUCTION
Motivations and Background
Cancelation of gauge anomalies is a basic requirement for constructing grand unified models,
and the usual assumption is that anomalies must cancel among spin
1
2
fermion fields. However,
a 1985 paper of Marcus [1] showed that in principle an SU (8) gauge theory can be constructed
with spin
3
2
Rarita-Schwinger fermions playing a role in anomaly cancelation, and we have recently
constructed [2] a family unification model incorporating this observation. Using gauged spin
3
2
fields in a grand unification model raises the question of whether such fields admit a consistent
quantum, or even classical theory. It is well known, from papers of Johnson and Sudarshan [3] and
Velo and Zwanziger [4], and much subsequent literature, that theories of massive gauged RaritaSchwinger fields have serious problems. Does setting the fermion mass to zero eliminate these
∗
Electronic address: adler@ias.edu
What We Can Learn from the Running of the Spectral Index
if no Tensors are Detected in the Cosmic Microwave Background Anisotropy
M. Biagetti,1 A. Kehagias,1, 2 and A. Riotto1
1
arXiv:1502.02289v1 [astro-ph.CO] 8 Feb 2015
2
D´epartement de Physique Th´eorique and Centre for Astroparticle Physics (CAP),
Universit´e de Gen`eve, 24 quai E. Ansermet, CH-1211 Geneva, Switzerland
Physics Division, National Technical University of Athens, 15780 Zografou Campus, Athens, Greece
(Dated: February 10, 2015)
In this paper we operate under the assumption that no tensors from inflation will be measured in
the future by the dedicated experiments and argue that, while for single-field slow-roll models of
inflation the running of the spectral index will be hard to be detected, in multi-field models the
running can be large due to its strong correlation with non-Gaussianity. A detection of the running
might therefore be related to the presence of more than one active scalar degree of freedom during
inflation.
Motivations.— Inflation [1] provides a mechanism to explain the initial conditions for the Large Scale Structure
(LSS) and for the Cosmic Microwave Background (CMB)
anisotropy. The seeds for the density scalar perturbations
are created from the quantum fluctuations “redshifted”
out of the Hubble radius during the early period of superluminal expansion of the universe. At the same time,
the generation of tensor (gravity-wave) fluctuations is a
generic prediction of an accelerated de Sitter expansion
of the universe [2].
To characterize the scalar and tensor perturbations
several observables are introduced: the spectral index (or
tilt) ns of the scalar perturbations, currently measured
to be ns = 0.9655 ± 0.0062 at 68% CL; the running with
the wavenumber k of the spectral index αs = dns /d ln k,
currently consistent with zero, αs = −0.00571 ± 0.0071
at 68% CL (assuming no tensors); and the level of local non-Gaussianities parametrized by fNL = 0.8 ± 5.0
at 68% CL and gNL = (−9.0 ± 7.7) × 104 at 68% CL.
All these figures are quoted from the last Planck releases
[3, 4]. Finally, the tensor-to-scalar ratio is bounded to be
r < 0.12 at 95% CL [5].
Many next-generation satellite missions, see for instance Refs. [6–8], are dedicated to measure the polarization of the CMB anisotropies. On large angular scales
the B-mode polarization of the CMB carries the imprint
of primordial gravitational waves, and its precise measurement would provide a powerful probe of the epoch
of inflation. The goal of these missions is to achieve a
measurement of r down to O(10−3 ).
While a detection of gravity waves from inflation will
be a major milestone for the inflationary paradigm, on
the other hand one needs to remember that going from
r = 10−1 down to r = 10−3 means testing the energy
scale of inflation Einf only by a factor (100)1/4 ' 3.1
4
better than current bounds (r scales like Einf
).
One should therefore envisage the situation in which
Nature has not be so kind to us to set the scale of the
energy of inflation within a factor of three away from the
current limits. In this paper we will therefore operate
under the working assumption that no tensors will be
measured in the future by the dedicated experiments.
While we hope this hypothesis will prove to be wrong
in the future, we believe it is reasonable to ask how else
we could learn something more about the inflationary
perturbations.
In this paper we turn our attention to the scale dependence of the tilt of the scalar perturbations. Our hypothesis on the tensor modes leads to a hardly detectable
running within single-field slow-roll models. On the other
hand, a negative result on tensors might indicate a low
level of the Hubble rate, leaving open the possibility that
the scalar perturbations are due to a light scalar field
other than the inflaton field. In such a case, our findings
indicate that a large running may be achieved thanks to
an interesting correlation between the running and the
level of non-Gaussianity. Such strong correlation exists
only in multi-field models of inflation, while it is missing in single-field slow-roll models. If no tensors will
be observed, a measurement of a sizable running of the
spectral index might therefore imply a sizable amount
of non-Gaussianity (and viceversa) and the presence of
more than one active scalar degree of freedom during inflation.
Our considerations are particularly relevant for the
goals of next missions designed to measure the three
dimensional structure of the universe, such as the ESA
mission EUCLID [9] and the NASA SPHEREx mission
[10], a proposed all-sky spectroscopic survey satellite.
For instance, the combination of the galaxy power spectrum and bispectrum leads to the forecasted 68% CL
errors σ(ns − 1) = 2.2 × 10−3 , σ(αs ) = 6.5 × 10−4 and
σ(fNL ) = 0.2 (for the local case) in the case of SPHEREx.
This is an improvement with respect to EUCLID forecasts of a factor ∼ 2 in αs and a factor ∼ 20 for the local
fNL (or ∼ 6 with the galaxy power spectrum only). For
the other parameters SPHEREx will deliver constraints
comparable to those expected from the EUCLID spectroscopic survey.
As EUCLID and (possibly) SPHEREx will strongly
narrow down the allowed parameter space in the
(αs , fNL )-plane, it is therefore extremely interesting and
Noname manuscript No.
(will be inserted by the editor)
Variational Analysis of Mass Spectra and Decay Constants for Ground
State Pseudoscalar and Vector Mesons in Light-Front Quark Model
Ho-Meoyng Choi 1 , Chueng-Ryong Ji 2 , Ziyue Li 2
1 Department
arXiv:1502.03078v1 [hep-ph] 10 Feb 2015
2 Department
of Physics, Teachers College, Kyungpook National University, Daegu, Korea 702-701
of Physics, North Carolina State University, Raleigh, North Carolina 27695-8202
the date of receipt and acceptance should be inserted later
Abstract Using the variational principle, we compute mass
spectra and decay constants of ground state pseudoscalar
and vector mesons in the light-front quark model (LFQM)
with the QCD-motivated effective Hamiltonian including
the hyperfine interaction. To avoid the issue of negative infinity in applying the variational principle to the computation of meson mass spectra, we smear out the Dirac delta
function in the hyperfine interaction. We compare the results from this variational analysis with the previous computation handling the hyperfine interaction as perturbation. We
also take a couple of different trial functions for the variation to examine the sensitivity of the variational results with
respect to the choice of the trial wave functions. Comparing the results with the experimental data of mass spectra
and decay constants for the ground state pseudoscalar and
vector mesons from π to ϒ , we note that the analysis of the
light meson sectors may need to be separately handled from
the analysis of the heavy meson sectors as the degree of improvement in the LFQM results appears dependent on the
meson sectors.
1 Introduction
Effective degrees of freedom to describe a strongly interacting system of hadrons have been one of the key issues in understanding the non-perturbative nature of QCD in the low
energy regime. Within an impressive array of effective theories available nowadays, the constituent quark model has
been quite useful in providing a good physical picture of
hadrons just like the atomic model for the system of atoms.
Absorbing the complicated effect of quark, antiquark and
gluon interactions into the effective constituent degrees of
freedom, one may make the problem more tractable yet still
keep some key features of the underlying QCD to provide
useful predictions [1]. The effective potentials used in con-
stituent quark models are typically described by the flux tube
configurations generated by the gluon fields as well as the
effective “one-gluon-exchange” calculation in QCD [2, 3].
In the QCD-motivated effective Hamiltonian, a proper way
of dealing with the relativistic effects in the hadron system
is quite essential due to the nature of strong interactions. In
particular, proper care and handling of relativistic effects has
been emphasized in describing the hadrons made of u, d, and
s quarks and antiquarks.
As a proper way of handling relativistic effects, the lightfront quark model (LFQM) [4–8] appears to be one of the
most efficient and effective tools in hadron physics as it
takes advantage of the distinguished features of the lightfront dynamics (LFD) [9, 10]. In particular, the LFD carries the maximum number (seven) of the kinetic (or interaction independent) generators and thus the less effort in dynamics is necessary in order to get the QCD solutions that
reflect the full Poincare´ symmetries. Moreover, the rational energy-momentum dispersion relation of LFD, namely
p− = (p2⊥ + m2 )/p+ , yields the sign correlation between the
light-front (LF) energy p− (= p0 − p3 ) and the LF longitudinal momentum p+ (= p0 + p3 ) and leads to the suppression of quantum fluctuations of the vacuum, sweeping the
complicated vacuum fluctuations into the zero-modes in the
limit of p+ → 0 [11–13]. This simplification is a remarkable
advantage in LFD and facilitates the partonic interpretation
of the amplitudes. Based on the advantages of the LFD, the
LFQM has been developed [14] and subsequently applied
for various meson phenomenologies such as the mass spectra of both heavy and light mesons [15], the decay constants,
distribution amplitudes, form factors and generalized parton
distributions [10, 14–23].
Despite these successes in reproducing the general features of the data, however, it has proved very difficult to obtain direct connection between the LFQM and QCD. Typically, rigorous derivations of the connection between the
Angular asymmetries as a probe
for anomalous contributions to HZZ vertex at the LHC
N. Belyaev
National Research Nuclear University (Moscow Engineering Physics Institute), 31 Kashirskoe Shosse, Moscow 115409, Russia
R. Konoplich
Department of Physics, New York University, 4 Washington Place, New York, NY 10003, USA∗
L. Egholm Pedersen
Niels Bohr Institute, University of Copenhagen, Blegdamsvej 17 Kobenhavn, Denmark
arXiv:1502.03045v1 [hep-ph] 10 Feb 2015
K. Prokofiev
Department of Physics, Hong Kong University of Science and Technology, Clear Water Bay, Kowloon, Hong Kong†
(Dated: February 11, 2015)
In this article, the prospects for studying the tensor structure of the HZZ vertex with the LHC
experiments are presented. The structure of tensor couplings in Higgs di-boson decays is investigated
by measuring the asymmetries and by studing the shapes of the final state angular distributions.
The expected background contributions, detector resolution, and trigger and selection efficiencies
are taken into account. The potential of the LHC experiments to discover sizeable non-Standard
Model contributions to the HZZ vertex with 300 fb−1 and 3000 fb−1 is demonstrated.
I.
INTRODUCTION
In the Summer of 2012, the CMS and ATLAS Collaborations at the LHC reported the discovery of a new neutral resonance in searches for the Standard Model Higgs
boson. This discovery was later confirmed by analyses
of the full LHC Run-I dataset by both collaborations
[1, 2]. It was demonstrated that the new particle with
a mass around 125.5 GeV was dominantly produced via
the gluon-fusion process and decays into pairs of gauge
bosons: γγ, ZZ and W W . The observed production and
decay modes identified the discovered particle as a neutral boson. The subsequent measurement of its couplings
to fermions and bosons demonstrated the compatibility
of the discovered resonance with the expectations for the
Standard Model Higgs boson within available statistics
[3–5].
In the Standard Model, electroweak symmetry breaking via the Higgs mechanism requires the presence of a
single neutral Higgs boson with spin 0 and even CPparity. Theories beyond the Standard Model often require an extended Higgs sector featuring several neutral
Higgs bosons of both even and odd CP-parity. In such
a case, mixing between Higgs boson CP-eigenstates is
possible. The Higgs boson mass eigenstates observed in
experiment may thus have mixed CP-parity. Such an extension of the Higgs sector is important because effects of
CP violation in the SM are too small and, in particular,
cannot explain the baryon asymmetry of the Universe.
Dedicated studies of spin and parity of the Higgs candidate discovered by ATLAS and CMS showed that its
dominant spin and parity are compatible with J CP =
0++ [4–6]. The dataset of about 25 fb−1 currently collected by each of the major LHC experiments allows
to set an upper limit on the possible CP-odd contribution. The sensitivity is expected to improve with larger
datasets to be collected at the LHC.
There have been many works on direct measurement
of CP violation in the Higgs sector [7–29]. In this paper
the sensitivity of LHC experiments to observe CP-mixing
effects with 300 fb−1 and 3000 fb−1 is evaluated using the
method of angular asymmetries.
This paper is organised as follows. In Section II observables sensitive to CP violation in the HZZ vertex are
discussed. The spin-0 model, a Monte Carlo production
of signal and background, and a lagrangian parametrisation for CP-mixing measurements are discussed in Section III. In Section IV the expected sensitivity of the LHC
experiments to the CP-violation effects based on angular asymmetries is presented. Constraits are set on the
contribution of anomalous couplings to the HZZ vertex.
Section V introduces the measurement technique based
on observables fit. Exclusion regions for the mixing angle
are presented. Section VI gives the overall summary of
obtained results.
II.
OBSERVABLES
In this paper we study the sensitivity of final state observables to the CP violating HZZ vertex in the process:
∗
†
Also at Physics Department, Manhattan College, 4513 Manhattan College Parkway, Riverdale, New York, NY 10471, USA.
Also at Institute for Advanced Study, HKUST, Clear Water Bay,
Kowloon, Hong Kong.
gg → H → ZZ → 4l.
(1)
Following the notation introduced in [21], the general
CFTP/15-01
arXiv:1502.03008v1 [hep-ph] 10 Feb 2015
New texture-zero models for lepton mixing
L. Lavoura∗
CFTP, Instituto Superior T´ecnico, Universidade de Lisboa
Avenida Rovisco Pais 1, 1049-001 Lisboa, Portugal
10 February 2015
Abstract
I systematically consider, in the context of the type-I see-saw mechanism, all the predictive cases in which both the Dirac mass matrix
connecting the left-handed neutrinos to the right-handed neutrinos,
and the Majorana mass matrix of the latter neutrinos, feature texture
zeros, while the mass matrix of the charged leptons is diagonal. I
have found a few cases which had not been discussed in the literature
previously.
1
Introduction
There has recently been renewed interest in the possibility of ‘texture’ zeros
in the fermion mass matrices [1, 2, 3]. Texture zeros are well grounded in
renormalizable field theories, since they can always be implemented through
models with suitable Abelian symmetries and (possibly many) scalar fields
with vacuum expectation values [4]. The revival of interest was partially
motivated by the realization of the fact that a popular alternative approach,
where lepton mixing is completely determined by a non-Abelian symmetry,
seems to have been fully explored [5].
With three Majorana neutrinos, the mass Lagrangian is
Lmass = −ℓ¯L Mℓ ℓR − ℓ¯R Mℓ† ℓL +
∗
1 T −1
ν C Mν − ν¯M ∗ C ν¯T ,
2
E-mail: balio@cftp.tecnico.ulisboa.pt
1
(1)
Prepared for submission to JHEP
FERMILAB-PUB-15-030-T
arXiv:1502.02990v1 [hep-ph] 10 Feb 2015
Higgs constraints from vector boson fusion and
scattering
John M. Campbell and R. Keith Ellis
Fermilab,
PO Box 500, Batavia, IL 60510, USA
E-mail: johnmc@fnal.gov, ellis@fnal.gov
Abstract:
We present results on 4-lepton + 2-jet production, the partonic processes most commonly described as vector boson pair production in the Vector Boson Fusion (VBF) mode.
This final state contains diagrams that are mediated by Higgs boson exchange. We focus
particularly on the high-mass behaviour of the Higgs boson mediated diagrams, which unlike on-shell production, gives information about the Higgs couplings without assumptions
on the Higgs boson total width. We assess the sensitivity of the high-mass region to Higgs
coupling strengths, considering all vector boson pair channels, W − W + , W ± W ± , W ± Z
and ZZ. Because of the small background, the most promising mode is W + W + which has
sensitivity to Higgs couplings because of Higgs boson exchange in the t-channel. Using the
Caola-Melnikov (CM) method, the off-shell couplings can be interpreted as bounds on the
Higgs boson total width. We estimate the bound that can be obtained with current data,
√
as well as the bounds that could be obtained at s = 13 TeV in the VBF channel for data
samples of 100 and 300 fb−1 . The CM method has already been successfully applied in
the gluon fusion (GGF) production channel. The VBF production channel gives important
complementary information, because both production and decay of the Higgs boson occur
already at tree graph level.
arXiv:1502.02986v1 [hep-ph] 10 Feb 2015
Kinematic biases on centrality selection of jet events in
pPb collisions at the LHC
N´estor Armesto
Departamento de F´ısica de Part´ıculas and IGFAE,
Universidade de Santiago de Compostela, E-15706 Santiago de Compostela, Galicia-Spain
Do˘
ga Can G¨
ulhan
Laboratory for Nuclear Science and Department of Physics,
Massachusetts Institute of Technology (MIT), Cambridge, MA 02139 USA
Jos´e Guilherme Milhano
CENTRA, Instituto Superior T´
ecnico,
Universidade de Lisboa, Av. Rovisco Pais, P-1049-001 Lisboa, Portugal
and
Physics Department, Theory Unit, CERN, CH-1211 Gen`
eve 23, Switzerland
Abstract
Centrality selection has been observed to have a large effect on jet observables
in pPb collisions at the Large Hadron Collider, stronger than that predicted by
the nuclear modification of parton densities. We study to which extent simple
considerations of energy-momentum conservation between the hard process and
the underlying event affect jets observables in such collisions. We develop a
simplistic approach that considers first the production of jets in a pp collision
as described by PYTHIA. From each pp collision, the value of the energy of the
parton from the proton participating in the hard scattering is extracted. Then,
the underlying event is generated simulating a pPb collision through HIJING,
but with the energy of the proton decreased according to the value extracted
in the previous step, and both collisions are superimposed. This model is able
to capture the bulk of the centrality effect for central to semicentral collisions,
for the two available sets of data: dijets from the CMS Collaboration and single
jets from the ATLAS Collaboration. As expected, the model fails for peripheral
collisions where very few nucleons from Pb participate.
∗ Preprint
number: CERN-PH-TH-2015-021.
Email addresses: nestor.armesto@usc.es (N´
estor Armesto), dgulhan@mit.edu (Do˘
ga
Can G¨
ulhan), guilherme.milhano@tecnico.ulisboa.pt (Jos´
e Guilherme Milhano)
Preprint submitted to Elsevier
February 11, 2015
Hunting for the Xb via hidden bottomonium decays
Gang Li,1,2∗ and Zhu Zhou1†
1
2
Department of Physics, Qufu Normal University, Qufu 273165, China
State Key Laboratory of Theoretical Physics, Institute of Theoretical Physics,
Chinese Academy of Sciences, Beijing 100190, China
(Dated: February 11, 2015)
arXiv:1502.02936v1 [hep-ph] 10 Feb 2015
In this work, we study the isospin conserved hidden bottomonium decay of Xb → Υ(1S)ω, where
Xb is taken to be the counterpart of the famous X(3872) in the bottomonium sector as a candidate
¯ ∗ threshold and the mass
for the meson-meson molecule. Since it is likely that the Xb is below the B B
difference between the neutral and charged bottom meson is small compared to the binding energy
of the Xb , the isospin violating decay mode Xb → Υ(nS)π + π − would be greatly suppressed. We use
the effective Lagrangian based on the heavy quark symmetry to explore the rescattering mechanism
of Xb → Υ(1S)ω and calculate the partial widths. Our results show that the partial width for the
Xb → Υ(1S)ω is about tens of keVs. Taking into account the fact that the total width of Xb may
be smaller than a few MeV like X(3872), the calculated branching ratios may reach to orders of
10−2 . These hidden bottomonium decay modes are of great importance in the experimental search
for the Xb particularly at the hadron collider. Also, the associated studies of hidden bottomonium
¯ may help us investigate the structure of Xb deeply. The
decays Xb → Υ(nS)γ, Υ(nS)ω, and B Bγ
experimental observation of Xb will provide us with further insight into the spectroscopy of exotic
states and is helpful to probe the structure of the states connected by the heavy quark symmetry.
PACS numbers: 13.25.Hw, 13.75.Lb, 14.40.Pq
I.
INTRODUCTION
During recent years, the experimental observation of a large number of so-called XY Z states has inspired tremendous
effort to unravel their nature beyond the conventional quark model [1–7]. In 2003, the Belle Collaboration first
reported the observation of X(3872) in the J/ψπ + π − invariant mass spectrum of B + → K + + J/ψπ + π − [8] which
was subsequently confirmed by the BaBar Collaboration [9] in the same channel. It was also discovered in protonproton/antiproton collisions by the D0 [10], CDF [11], and LHCb Collaborations [12, 13]. The X(3872) is the
first, and perhaps the most renowned exotic candidate; however, its nature is still ambiguous due to its peculiar
properties. First, only an upper bound of the total width has been measured experimentally: Γ < 1.2 MeV [14],
which is tiny compared to typical hadronic widths. Second, the mass is located close to the D0 D
∗0
threshold,
MX(3872) − MD0 − MD∗0 = (−0.12 ± 0.24) MeV [15], which leads to speculation that the X(3872) is presumably a
meson-meson molecular state [16, 17].
Many studies on the production and decay of the X(3872) have been carried out in order to understand its nature.
The discrimination of a compact multiquark configuration and a loosely bound hadronic molecule configuration is one
important aspect. From this point, it is also valuable to look for the counterpart in the bottom sector, denoted as Xb
following the notation in Ref. [18], as states related by heavy quark symmetry may have universal behaviors. Since
∗
†
gli@mail.qfnu.edu.cn
zhouzhumail@163.com
¯0 → K
¯ ∗0 X(Y Z) and B
¯ 0 → φX(Y Z) with X(4160), Y (3940), Z(3930)
Predictions for the B
s
Wei-Hong Liang,1, 2 Ju-Jun Xie,2, 3, 4 and E. Oset2, 5
1
Department of Physics, Guangxi Normal University, Guilin 541004, China
Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000, China
3
Research Center for Hadron and CSR Physics, Institute of Modern
Physics of CAS and Lanzhou University, Lanzhou 730000, China
4
State Key Laboratory of Theoretical Physics, Institute of Theoretical Physics,
Chinese Academy of Sciences, Beijing 100190, China
5
Departamento de F´ısica Te´
orica and IFIC, Centro Mixto Universidad de Valencia-CSIC
Institutos de Investigaci´
on de Paterna, Aptdo. 22085, 46071 Valencia, Spain
(Dated: February 11, 2015)
arXiv:1502.02932v1 [hep-ph] 10 Feb 2015
2
¯0 → K
¯ ∗0 R and B
¯s0 → φR with R being the X(4160), Y (3940),
We investigate the decay of B
Z(3930) resonances. Under the assumption that these states are dynamically generated from the
vector-vector interaction, as has been concluded from several theoretical studies, we use a reaction
mechanism of quark production at the elementary level, followed by hadronization of one final q q¯
pair into two vectors and posterior final state interaction of this pair of vector mesons to produce
the resonances. With this procedure we are able to predict five ratios for these decays, which are
closely linked to the dynamical nature of these states, and also predict the order of magnitude of
the branching ratios which we find of the order of 10−4 , well within the present measurable range.
The measurement of these decays rates can help unravel the nature of these resonances.
PACS numbers:
I.
INTRODUCTION
The XY Z resonances with masses in the region around
4000 MeV have stirred the hadron community with a
series of states that challenge the common wisdom of
mesons as made from q q¯. There has been intense experimental work done at the BABAR, BELLE, CLEO, BES
and other collaborations, and many hopes are pinned in
the role that the future FAIR facility with the PANDA
collaboration and J-PARC will play in this field. There
are early experimental reviews on the topic [1–4] and
more recent ones [5–9]. From the theoretical point of
view there has been also an intensive activity trying
to understand these intriguing states. There are quark
model pictures [10, 11] and explicit tetraquark structures
[12]. Molecular interpretations are given in refs. [13–21].
Much progress also has been done using the heavy quark
spin symmetry (HQSS) [22, 23]. Predictions using QCD
sum rules have also brought some light into the issue
[24–26]. Strong decays of these resonances have been
studied to learn about the nature of these states [27, 28],
while very often radiative decays are invoked as a tool to
provide insight into this problem [29–33], although there
might be exceptions as discussed in ref. [34]. It has even
been speculated that some states found near thresholds
of two mesons could just be cusps, or threshold effects
[35, 36]. Some theoretical reports on these issues can be
found in refs. [37–39].
On the other hand, and somewhat unexpected, recent
experiments on the weak decays of B meson are proving
to be a powerful source of information on hadron dynamics and the nature of hadronic states [40–45]. One of the
recent surprises was to see from these experiments a pronounced peak for the f0 (980) in Bs0 decay into J/ψ and
π + π − [40] while the signal for the f0 (500) was found very
small or non-existent. Simultaneously, in the analogous
¯ 0 into J/ψ and π + π − [44] a signal was seen for
decay of B
the f0 (500) production and only a very small fraction was
observed for the f0 (980) production. This is surprising
since the f0 (500) couples more strongly to π + π − than to
the f0 (980). Some attempts to explain this behaviour
was offered in ref. [46] in terms of tetraquark structures for the scalar mesons. Furthermore, the f0 (500)
and f0 (980) resonances are naturally explained as states
dynamically generated from the meson-meson interaction
in chiral unitary theory [47–52]. From this perspective
the features observed in these experiments and different
ratios were well described in ref. [53]. The basic approach in ref. [53] was to identify the dominant mechanism of the decays at the quark level, implementing the
hadronization of the final q q¯ pair into two mesons and
allowing them to interact to generate the f0 (500) and
f0 (980) resonances.
The picture of ref. [53] has been extended to describe many other B and D decays, with equal success
in the description of observed features of the reactions.
In ref. [54] ratios for the production of vector mesons
in the final states were evaluated and predictions for the
¯s0 → J/ψκ(800) decay were made. In ref. [55] the
B
D0 decays into Ks0 and f0 (500), f0 (980), a0 (980) were
studied. A different sort of states, dynamically generated from the vector-vector interaction were investigated
¯ 0 and B
¯s0 decays into J/ψ and
in ref. [56] in the B
f0 (1370), f0 (1710), f2 (1270), f2′ (1525), K2∗ (1430). In
¯ 0 decay into D0 and ρ or f0 (500), f0 (980),
ref. [57] the B
¯ 0 decay into D0 and K ∗0 or κ(800) were
a0 (980) and B
s
studied. Similarly, the Bs0 decay into Ds DK was studied with the aim of learning about KD scattering and the
∗
Ds0
(2317) resonance [58]. Related work to this latter one
arXiv:1502.02931v1 [hep-ph] 10 Feb 2015
Search for Charged Higgs bosons via decays to W ±
and a 125 GeV Higgs at the Large Hadron Collider
Rikard Enberga , William Klemm∗a , Stefano Morettib , Shoaib Munira
and Glenn Woudaa
a Department
of Physics and Astronomy, Uppsala University
Box 516 , SE-Uppsala, Sweden
of Physics & Astronomy, University of Southampton, Highfield,
Southampton SO17 1BJ, UK
E-mail: rikard.enberg@physics.uu.se, william.klemm@physics.uu.se,
S.Moretti@soton.ac.uk, shoaib.munir@physics.uu.se,
glenn.wouda@physics.uu.se
b School
The recent observation of a 125 GeV neutral Higgs boson (Hobs ) provides additional input for
charged Higgs boson searches in the H ± → W ± Hobs decay channel at the Large Hadron Collider (LHC). We reassess the discovery potential in this channel, which is important for H ±
heavier than the top quark mass. When Hobs decays to a bb¯ pair, knowledge of the Higgs
mass aids in the kinematic selection of signal events. We perform a signal-to-background analysis to demonstrate the LHC prospects for charged Higgs discovery in the resulting channel
¯ − → `± ν` j jbbb(
¯ b)+h.c.
¯
pp → t(b)H
for standard (300 fb−1 ) and high (3000 fb−1 ) luminosities
√
at design energy, s = 14 TeV. We find that regions of the parameter space of several two-Higgs
doublet models, consistent with constraints from LHC Higgs searches and b-physics observables,
are testable in this channel.
Prospects for Charged Higgs Discovery at Colliders
16-18 September 2014
Uppsala University Sweden
∗ Speaker.
c Copyright owned by the author(s) under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike Licence.
Search for H ± → W ± Hobs at the LHC
http://pos.sissa.it/
William Klemm
1. Introduction
The observation of a Higgs boson (Hobs ) [1] at the Large Hadron Collider (LHC) may be
just the first glimpse into the rich phenomenology of a larger Higgs sector. Indeed, many models
require additional Higgs states, including charged Higgs bosons (H ± ), the observation of which
would be a clear sign of physics beyond the standard model (SM). Experimental searches for H ±
have largely focused on decays to tb or τν, which dominate much of the parameter space of many
models. However, when kinematically allowed, the decay H ± → W ± Hobs can become significant
for many parameter configurations. Earlier studies [2] demonstrated the potential of this channel,
and the newfound knowledge of the Higgs mass, mHobs ≈ 125 GeV, provides an additional input for
the analysis and a constraint on extensions of the Higgs sector (see also [3] for a recent discussion).
Here we describe a collider analysis for the H ± → W ± Hobs channel and determine its sensitivity at
the LHC, which we compare to the possible signal strengths of several two Higgs doublet models
(2HDMs) compatible with current experimental observations.
2. Collider Analysis
The main production channel at the LHC for a charged Higgs above the top mass is typically
pp → t(b)H ± ,1 which is possible through the coupling of the charged Higgs to third generation
¯
quarks. Focusing then on H ± → HobsW ± decays, we consider the subsequent decay Hobs → bb,
as both b-quarks are observable, allowing us to directly reconstruct the observed 125 GeVstate,
and because SM-like Higgs bosons in this mass range decay dominantly in this channel.2 The
process we then wish to search for is pp → (b)tH ± → (b)bW ∓W ± Hobs → (b)bbb j j`ν` , where one
of the W -bosons (from either H ± or top decay) decays leptonically and the other hadronically. The
presence of a single lepton allows us to avoid multi-jet backgrounds, while requiring one hadronic
W avoids additional unseen neutrinos, making the event reconstruction more straightforward. The
¯ where either an additional b-tagged jet combines with
main background for this process is t t¯b(b),
a b-jet from a top decay or an additional bb¯ pair mimics an Hobs → bb¯ decay.
To get a measure of the sensitivity that could be obtained at the 14 TeV LHC, we generate the
t(b)H ± signal using Pythia 6.4.28 [4] with the MATCHIG [5] add-on to avoid double counting
among bg → tH ± and gg → tbH ± processes, and all t(b)W X, X → bb¯ backgrounds with MadGraph5 [6]. Both signal and background undergo parton showering and hadronization using Pythia
8 [7] and are further processed with the DELPHES 3 [8] detector simulation using experimental
parameters based on the ATLAS experiment with modified b-tagging efficiencies.3 To reconstruct
our signal events and reduce background, we use the following procedure, inspired by previous
studies [2], with an additional top veto:
1 This should be interpreted as pp → t(b)H
¯ − + pp → t¯(b)H + . Throughout this text, we will not distinguish fermions
and anti-fermions when their identity is unspecified and/or can be inferred.
2 In principle, other decay channels could also be competitive. It has been suggested that, especially in analyses
dominated by systematic errors, the Hobs → τ + τ − channel could be useful despite additional missing energy from τ
decays and a reduced branching ratio, largely as a result of lower backgrounds [3].
3 The b-tagging efficiency chosen is ε tanh(0.03p − 0.4), with ε = 0.7 for central (|η| ≤ 1.2) and ε = 0.6 for
η
η
η
T
forward (1.2 ≤ |η| ≤ 2.5) jets, and the transverse momentum, pT , in GeV. This is a conservative choice compared with
high-luminosity projections.
2
arXiv:1502.02857v1 [hep-ph] 10 Feb 2015
Photon emission rates near the critical point in the
linear sigma model
F. Wunderlich
Helmholtz-Zentrum Dresden-Rossendorf, Institute of Radiation Physics, Bautzner Landstr. 400,
D-01328 Dresden, Germany
and
Institut für Theoretische Physik, Technsche Universität Dresden, D-01062 Dresden, Germany
E-mail: f.wunderlich@hzdr.de
B. Kämpfer∗
Helmholtz-Zentrum Dresden-Rossendorf, Institute of Radiation Physics, Bautzner Landstr. 400,
D-01328 Dresden, Germany
and
Institut für Theoretische Physik, Technsche Universität Dresden, D-01062 Dresden, Germany
E-mail: kaempfer@hzdr.de
Employing the linear sigma model, the effective masses of quasi-particle excitations are found
to exhibit significant variations within the phase diagram, which has a critical point at non-zero
chemical potential, where a first-order phase transition sets in. Soft-photon emission rates in
lowest order display, for selected channels, a sensible dependence on the effective masses of the
involved excitations and let us argue that they could map out the phase diagram.
9th International Workshop on Critical Point and Onset of Deconfinement - CPOD2014,
17-21 November 2014
ZiF (Center of Interdisciplinary Research), University of Bielefeld, Germany
∗ Speaker.
c Copyright owned by the author(s) under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike Licence.
Photon emission rates near the critical point in the linear sigma model
http://pos.sissa.it/
B. Kämpfer
1. Introduction
Confinement and spontaneous symmetry breaking as well as their respective counterparts - deconfinement and chiral restoration - are central issues of QCD. Their mutual relationship is among
the main questions investigated in heavy ion collisions (HICs). A particularly challenging task
is the establishment of the QCD phase diagram in a region of temperature T and baryo-chemical
potential µ which is accessible in HICs. While the beam energy scan at RHIC and forthcoming
accelerator/detector installations, e.g. at FAIR/CBM and NICA/MPD, aim at finding signatures of
the onset of deconfinement as a first-order phase transition in a critical point (CP), QCD based [1,2]
and QCD rooted [3] calculations try to quantify its coordinates. Instead of facing the sign problem of QCD at non-zero baryon density, one can resort to suitable models which display a CP
at (TCP , µCP ) > (0, 0) and a line of first-order phase transitions for µ > µCP (cf. [4, 5] for recent
surveys). By universality arguments, one can elucidate observables signaling the CP.
In the previous search for deconfinement effects in HICs, electromagnetic probes (cf. [6–8] for
recent evaluations and further references) have been considered as promising since, by their penetrating nature, they monitor the full space-time evolution of matter in the course of HICs. Given the
proximity of deconfinement and chiral restoration at µ /T ≪ 1, the dilepton spectra have been considered in [9, 10] as candidates for messengers of chiral restoration. It appeared that at the pseudocritical temperature of Tpc ∼ 154 MeV the dilepton emission rates of confined matter (hadrons) and
deconfined matter (quarks and gluons) become degenerate - quite natural since Tpc quantifies the
cross over location at µ /T ≪ 1. This degeneracy can be named quark-hadron duality and has been
employed [11–13] to verify a “thermal radiation” component besides hard initial yield and electromagnetic hadron final-state decays after the disassembly of the fireball in HICs. The approximate
degeneracy of real-photon emission rates of confined and deconfined matter has been pointed out
quite early [14] and can be used analogously to arrive at a consistent modeling of thermal radiation
in HICs, either schematically [15, 16] or with many refinements [17–19].
The recent analysis in [17, 20], however, revealed that the calculated photon spectra fall short in
comparison with data. The tension is caused, to some extent, by the consistency requirement of
photon-v2 and photon-p⊥ systematics. According to [17,18], a solution is offered by the hypothesis
of a “pseudo-critical enhancement” of the photon emission at Tpc ± ∆T with ∆T = O(15 MeV). It
is therefore tempting to look for arguments which could support the hypothesis launched there and,
more general, to extend the consideration over the QCD phase diagram and to check whether the
CP can have a distinguished impact on the photon emission rate.
2. Linear σ model
We utilize here the linear sigma model (Lσ M), which has been originally designed to model spontaneous chiral symmetry breaking [21] and has been later coupled to the fermionic sector. It is a
special quark-meson model with the Lagrangian LLσ M = L∂ ψ + Lψ M + L∂ M + LM + Ls.b. , where
the kinetic terms L∂ ψ and L∂ M are supplemented by the O(4) symmetric meson self-interaction
LM , which refers to an SU (2)L × SU (2)R symmetry which, in combination with the symmetry
breaker Ls.b. = H σ , dynamically generates mass terms; the fermion-meson coupling of Yukawa
type is encoded in Lψ M . The field content of L is a two component Fermion (light quark doublet
2
The signatures of the quintuplet leptons at the LHC
You Yu 1 , Chong-Xing Yue 1 ,∗ and Shuo Yang
1
Department of Physics, Liaoning Normal University, Dalian 116029, China
2
arXiv:1502.02801v1 [hep-ph] 10 Feb 2015
2†
Physics Department, Dalian University, Dalian, 116622, China
Abstract
We investigate production and detection prospects of the quintuplet heavy leptons at the LHC
in the context of a new model which is proposed as a viable and testable solution to the neutrino
masses problem. We classify the signals that the heavy leptons produce in terms of the charged
lepton multiplicity. The 2l± l∓ 2j/
ET and 2l± 2l∓ 2j signals are mainly studied that we carry out
a full simulation in this paper. After applying suitable kinematic cuts, the background events
are substantially suppressed. We also study the 3l± l∓ 2j, 3l± l∓ /ET and 3l± 3l∓ signals. The
production rate of the 3l± 3l∓ signal is much small, while other signatures of the heavy leptons
might be detected at the 14TeV LHC.
PACS numbers: 14.60.Hi, 14.60.Pq, 13.85.Qk
∗
Electronic address: cxyue@lnnu.edu.cn
†
Electronic address: yangshuo@dlu.edu.cn
1
Flavor dependence of normalization constant for an infrared renormalon
Taekoon Lee∗
Department of Physics, Kunsan National University, Kunsan 573-701, Korea
arXiv:1502.02698v1 [hep-ph] 9 Feb 2015
An ansatz is proposed for the flavor dependence of the normalization constant for the first IR
renormalon in heavy quark pole mass.
The ultraviolet (UV) and infrared (IR) renormalons in field theory are fascinating objects that give rise to factorially
growing large order behavior in perturbation theory. In quantum chromodynamics (QCD) the IR renormalons can
be understood within the framework of operator product expansion (OPE) [1–6]. An IR renormalon in a Wilson
coefficient in the OPE causes ambiguity in the resummed asymptotic series of the Wilson coefficient, which is to
be cancelled by the vacuum condensate of an higher dimensional operator. This cancellation of the ambiguities in
the resummation and vacuum condensate determines the nature of the renormalon singularities in the Borel plane.
Specifically, the functional form of the condensate in the strong coupling αs , which can be determined up to an
overall constant by renormalization group (RG) equation, determines the power of singularity as well as its location
[7]. However, the residue of the singularity, which is the normalization constant of the renormalon-caused large order
behavior, is not known, but it can be calculated by a perturbation method [8, 9]. While the normalization can be
expressed in a convergent series, with finite order perturbation it can only be calculated approximately. Its exact
form is a nonperturbative quantity and so far there is no known way to calculate it. It would thus be very interesting
if we somehow find the exact form for the normalization.
Our purpose in this Letter is to present an ansatz for the normalization for the first IR renormalon in the heavy
quark pole mass. In this case the perturbation method for the normalization yields a series that converges rather
quickly, which allows to determine the normalization within a few percent of uncertainty using the known first three
perturbative coefficients [10, 11]. The reason for this rapid convergence and accuracy may lie with following two facts.
2
First, the renormalon singularity is relatively soft, with its singularity of (1 − 2b)−(1+β1 /2β0 ) , for example, compared
2
to that of the first IR renormalon in Adler function, which is of (1 − b/2)−(1+2β1 /β0 ) , where β0 , β1 are the first two
coefficients of the beta function and b is the complex variable for the Borel plane. With vanishing flavor number
Nf = 0, for example, the singularities are (1 − 2b)−1.42 and (1 − b/2)−2.69 , respectively. Secondly, the IR renormalon
is the closest singularity to the origin in the Borel plane. This condition is important because the normalization in the
perturbation method is evaluated on the boundary of convergence disk and for that to work the singularity should be
closer to the origin than any other singularities. Of course, any renormalon singularity can be moved by a conformal
mapping to be the closest one to the origin, this step is not required with the first IR renormalon for the pole mass,
because it is already the closest one, and this seems to help the convergence. The normalization constant obtained
from perturbation method was confirmed by recent lattice calculation of large order behaviour of static energy [12, 13].
To get the ansatz let us assume that the condensate in the OPE is of dimension n and is proportional to
n
−
ΛnQCD ∼ e− 2β0 αs α
nβ1
2β 2
0
(1 + O(αs ))
(1)
and the associated renormalon singularity is of the form:
N
.
(1 − b/b0 )1+ν
(2)
Then the imaginary part, which is ambiguous, of the Borel integral
Z ∞
1
N
Im
db = ±N sin(νπ)Γ(−ν)(b0 /β0 )1+ν e−b0 /β0 αs α−ν
e−b/β0 αs
s (1 + O(αs ))
β0 0
(1 − b/b0 )1+ν
(3)
is to be cancelled by ambiguity of the form (1). Thus identifying (3) with (1) we get
b0 = n/2 , ν = nβ1 /2β02 , N =
C( 2βn0 )ν
,
sin(νπ)Γ(−ν)
(4)
where C is an unknown proportionality constant. Now putting
C = C0 f (ν)
∗
(5)
tlee@kunsan.ac.kr
2
Nf
0
1
2
3
4
5
Npert.
0.6081 0.5981 0.5867 0.5730 0.5551 0.5288
N /Npert. 1.0047 0.9979 0.9973 1.0081 1.0403 1.116
TABLE I. Comparison of the ansatz (9) with normalization from perturbation method for varying number of flavors.
with f (0) = 1, where C0 is determined so that the normalization agrees with that from the large-β0 approximation
at ν = 0, we get
N =
C0 f (ν)( 2βn0 )ν
.
sin(νπ)Γ(−ν)
(6)
We shall now consider the normalization for the pole mass, for which n = 1. While in this case the ambiguity in
Borel summation is not canceled by a condensate of dimension one operator but by the static inter-quark potential
[14], the ambiguity is nevertheless of the form (1) and the relations (4) are still valid. For this case the large-β0
approximation fixes C0 in the MS scheme as [15–17]
C0 = −CF e5/6 ,
(7)
where CF = 4/3 for QCD. Of course f (ν) is not known, and we can only guess it by comparing the normalization
with values from the perturbation method. This gives
f (ν) = 4−ν
(8)
and, finally,
CF e 6 ( β20 )ν
,
sin(νπ)Γ(−ν)
5
N =−
(9)
β1 /2β02 .
This is our proposed ansatz.
for the MS scheme, where ν =
How well does this ansatz work? Table I compares the ansatz with the normalization from the perturbative method
for varying number of flavors, the details of which will be discussed shortly. The agreement is quite impressive for
up to Nf = 4. It is to be noted that the perturbative method tend to work better for smaller Nf . Of course, this
does not mean that the ansatz is necessarily correct. One test may be to expand (9) for small ν and compare it with
subleading corrections in large-β0 approximation, for which only partial result exists [18]. Expanding (9) at ν = 0,
we have
N =
CF e5/6
[1 + (γE + log(β0 /2))ν + O(ν 2 )] .
π
(10)
The Euler constant term agrees with the corresponding term in [18]. It is worth noting that the two transcendental
numbers π and γE in (10) both arise from
sin(νπ)Γ(−ν)
(11)
in the denominator in (9). This is a strong indication that the term should be, at least, part of the exact form for the
normalization.
It may be tempting to use the same idea to make an ansatz for other renormalons, for example, such as the first IR
renormalon in the Adler function, which is associated with the gluon condensate, for which n = 4. However, there is
no accurate estimate of the normalization for the Adler function; The convergence from the perturbative method is
not fast [19]. Without accurate numerical estimates for the normalization it is impossible to infer f (ν) for the Adler
function and that blocks such an attempt. Nevertheless, if we assume (8) is applicable to the Adler function as well,
then we have an ansatz for the first IR renormalon of the Adler function
3
CF e 3 ( β80 )ν
N =−4
,
sin(νπ)Γ(−ν)
10
(12)
where ν = 2β1 /β02 , and the following large-β0 result is used [17, 20, 21]:
C0 =
10
3
CF e 3 .
4
(13)
arXiv:1502.02682v1 [hep-ph] 9 Feb 2015
Non-conventional mesons at PANDA
Francesco Giacosa
Abstract. Non-conventional mesons, such as glueballs and tetraquarks, will be in the focus
of the PANDA experiment at the FAIR facility. In this lecture we recall the basic properties of
QCD and describe some features of unconventional states. We focus on the search of the not-yet
discovered glueballs and the use of the extended Linear Sigma Model for this purpose, and on
the already discovered but not-yet understood X, Y, Z states.
Institute of Physics, Jan Kochanowski University, 25-406 Kielce, Poland and Institute for
Theoretical Physics, J. W. Goethe University, Max-von-Laue-Str. 1, 60438 Frankfurt am
Main, Germany
1. Introduction
Conventional mesons are bound states made by a quark and an antiquark. Yet, since the
very beginning of QCD the search for other possibilities has attracted the attention of both
experimentalists and theoreticians [1].
As a prominent example, glueballs were predicted long ago: they are (yet hypothetical) bound
states of solely gluons. Computer simulations of QCD on the lattice have found a full spectrum
of these states [2, 3], but their firm experimental discovery has not yet taken place. On the other
hand, a plenty of mesons, denoted as X, Y, and Z states, has been unambiguously discovered
in the last decade in the energy region of charm-anticharm and botton-antibotton states [4, 5].
A clear explanation about the nature of these states is still lacking (tetraquark and molecular
hypotheses are a possibility).
The PANDA experiment at the FAIR facility [6] in Darmstadt/Germany is designed to shed
light on these questions. It is a proton-antiproton scattering experiment in which the energy of
the antiproton can be finely tuned in such a way that a wide energy range in the charmonium
region can be scanned. Various resonances can be directly formed in proton-antiproton fusion
processes. Glueball, if existent, shall be found by this experiment. On the other hand, many of
the X, Y, and Z states can also be formed and/or produced with high statistics. In this lecture a
theoretical view concerning the search of non-conventional mesons at PANDA will be presented.
2. Brief recall of the QCD Lagrangian and its symmetries
The Lagrangian of Quantum Chromodynamics (QCD) reads
LQCD =
Nf
X
i=1
1
q i (iγ µ Dµ − mi )qi − Gaµν Ga,µν , Dµ = ∂µ − ig0 Aµ
4
(1)
where Gaµν = ∂µ Aaν − ∂ν Aaµ + g0 f abc Abµ Acν , Aµ = Aaµ ta , a, = 1, ..., Nc2 − 1 = 8, and ta and f abc
are the generators and the structure constants of the group SU (Nc ). LQCD contains Nf quark
CUMQ/HEP 188
Dark Matter in the Higgs Triplet Model
Sahar Bahrami1a and Mariana Frank1b
1
Department of Physics, Concordia University,
7141 Sherbrooke St. West , Montreal, Quebec, Canada H4B 1R6.
(Dated: February 11, 2015)
arXiv:1502.02680v1 [hep-ph] 9 Feb 2015
Abstract
The inability to predict neutrino masses and the existence of the dark matter are two essential
shortcomings of the Standard Model. The Higgs Triplet Model provides an elegant resolution of
neutrino masses via the seesaw mechanism. We show here that introducing vectorlike leptons in
the model also provides a resolution to the problem of dark matter. We investigate constraints,
including the invisible decay width of the Higgs boson and the electroweak precision variables, and
impose restrictions on model parameters. We analyze the effect of the relic density constraint on
the mass and Yukawa coupling of dark matter. We also calculate the cross sections for indirect and
direct dark matter detection and show our model predictions for the neutrino and muon fluxes from
the Sun, and the restrictions they impose on the parameter space. With the addition of vectorlike
leptons, the model is completely consistent with dark matter constraints, in addition to improving
electroweak precision and doubly charged mass restrictions, which are rendered consistent with
present experimental data.
PACS numbers: 14.80.Fd, 12.60.Fr, 14.60.Pq
Keywords: LHC phenomenology, Higgs Triplet Model
a
Email: sahar.bahrami@concordia.ca
b
Email: mariana.frank@concordia.ca
1
Generically large nongaussianity in small multifield inflation
Joseph Bramante
Department of Physics
University of Notre Dame
Notre Dame, IN, 46556, USA
arXiv:1502.02674v1 [hep-ph] 9 Feb 2015
If forthcoming measurements of cosmic photon polarization restrict the primordial
tensor-to-scalar ratio to r < 0.01, small field inflation will be a principal candidate
for the origin of the universe. Here we show that small multifield inflation, without
the hybrid mechanism, typically results in large squeezed nongaussianity. Small multifield potentials contain multiple flat field directions, often identified with the gauge
invariant field directions in supersymmetric potentials. We find that unless these
field directions have equal slopes, large nongaussianity arises. After identifying relevant differences between large and small two-field potentials, we demonstrate that the
latter naturally fulfill the Byrnes-Choi-Hall large nongaussianity conditions. Computations of the primordial power spectrum, spectral index, and squeezed bispectrum,
reveal that small two-field models which otherwise match observed primordial perturbations, produce excludably large nongaussianity if the inflatons’ field directions
have unequal slopes.
2
I.
INTRODUCTION
Learning what forms of cosmological inflation are favored by observation deepens our
understanding of the universe’s origin and structure. This paper shows that if inflation is
sourced by multiple scalar fields traversing sub-Planckian field ranges, the Planck Collabsq
oration’s bound on squeezed (aka local) nongaussianity, fNL
= 2.5 ± 5.7 [1], often implies
a certain structure for small multifield potentials; without this structure they generically
1
produce large squeezed nongaussianity. This has implications for the couplings of lifted flat
directions in broken supersymmetric potentials, proposed as natural candidates for small
field inflation [3].
The nearly unbroken isotropy of the cosmic microwave background (CMB) provides an
amusing counterexample to the well-worn notion that physicists enjoy spherical symmetry.
Simply assuming that the universe began as a uniformly dense patch of radiation does not
adequately explain this uniformity, which amounts to a fine-tuning of the universe’s initial
conditions [4]. Inflation makes this uniformity plausible, because an epoch of exponential
spatial expansion (de Sitter space) fueled by a near-constant vacuum energy and preceding
the radiation and matter dominated expansions of our universe, provides a common origin
for otherwise causally separated lightcones on our cosmic horizon, which at present time
contains primordial photons of almost equal temperature, released when the formation of
hydrogen made the universe more transparent.
More concisely, the symmetry of a de Sitter space could be the source of spherical symmetry on the cosmic microwave background. But any such antecedent de Sitter space cannot
be totally time symmetric: inflation must end so its effects can be observed. A simple
mechanism that achieves this is a scalar field slowly-rolling down its potential, resulting
in a slowly-decreasing vacuum energy that sources a quasi-de Sitter space. The necessary
slowness of this roll can be quantified with the parameters
m2pl Vφ 2
Vφφ
≡ φ < 1,
m2pl
≡ ηφ < 1,
(1)
2
V
V
where V (φ) is a scalar potential and Vφ ≡ dV
is the slope of the potential. The expansion
dφ
fomented by this potential is measured with the scale factor of the universe, a ∝ eHt , where
H ≡ aa˙ is the Hubble rate, which can be determined from the equations of motion and
continuity for a scalar field sourcing de Sitter,
1 ˙2
φ¨ + 3H φ˙ + Vφ = 0,
φ + V − 3m2pl H 2 = 0,
(2)
2
where in the slow-roll limit the first term in each of these equations can be omitted.
In order for our universe to be causally connected at the time of big bang nucleosynthesis,
the universe needs to have expanded to roughly e60 times its initial size during inflation,
where the exponent is called the number of efolds, N . The expansion rate gets larger with
larger vacuum energy, V (φ), and inflation lasts longer with a smaller slope, Vφ . Thus it is
sensible (and with Eq. (2) verifiable) that in the slow-roll limit, N takes the form
Z te
Z φe
1
V
N=
Hdt = 2
dφ,
(3)
mpl φ∗ Vφ
t∗
1
In this work we only consider multiple small field models which terminate inflation with the dynamics
of the inflating fields themselves. These considerations will also apply to some (though not all) small
multifield hybrid models [2].
Predictions for Sivers single spin asymmetries in one- and two-hadron
electroproduction at CLAS12 and EIC
Hrayr H. Matevosyan,1 Aram Kotzinian,2, 3 Elke-Caroline Aschenauer,4 Harut Avakian,5 and Anthony W. Thomas1
1
arXiv:1502.02669v1 [hep-ph] 9 Feb 2015
ARC Centre of Excellence for Particle Physics at the Tera-scale,
and CSSM, School of Chemistry and Physics,
The University of Adelaide, Adelaide SA 5005, Australia
http://www.physics.adelaide.edu.au/cssm
2
Yerevan Physics Institute, 2 Alikhanyan Brothers St., 375036 Yerevan, Armenia
3
INFN, Sezione di Torino, 10125 Torino, Italy
4
Physics Department, Brookhaven National Laboratory, Upton, NY 11973, USA
5
Thomas Jefferson National Accelerator Facility,
12000 Jefferson Ave. Suite 5, Newport News, VA 23606, USA
(Dated: February 11, 2015)
The study of the Sivers effect, describing correlations between the transverse polarization of the
nucleon and its constituent (unpolarized) parton’s transverse momentum, has been the topic of a
great deal of experimental, phenomenological and theoretical effort in recent years. Semi-Inclusive
Deep Inelastic Scattering measurements of the corresponding single spin asymmetries (SSA) at the
upcoming CLAS12 experiment at JLab and the proposed Electron-Ion Collider will help to pinpoint
the flavor structure and the momentum dependence of the Sivers parton distribution function describing this effect. Here we describe a modified version of the PYTHIA6 Monte Carlo event generator
that includes the Sivers effect. Then we use it to estimate the size of these SSAs, in the kinematics
of these experiments, for both one and two hadron final states of pions and kaons. For this purpose
we utilize the existing Sivers parton distribution function (PDF) parametrization extracted from
HERMES and COMPASS experiments. We also show that the the leading order approximation
commonly used in such extractions provides significantly underestimated values of Sivers PDFs, as
the omitted parton showers and non-DIS processes play an important role in these SSAs at lower
light-cone momentum fraction, for example in the COMPASS kinematics.
PACS numbers: 13.88.+e, 13.60.-r, 13.60.Hb, 13.60.Le
I.
INTRODUCTION
The study of the structure of the nucleon has long been
a focus of both theory and experiment within the medium
and the high energy hadronic physics community, mostly
concentrating on the distributions of the longitudinal momentum fraction of partons within nucleon described by
the transverse momentum integrated (”collinear”) parton distribution functions (PDF). More recently, exploring the transverse structure of the nucleons in momentum space via transverse momentum dependent (TMD)
PDFs and the generalized parton distribution functions
in impact parameter space has attracted great interest.
The spin of the nucleon and its constituent partons plays
an important role when describing the transverse structure of the nucleon. Here we will focus on the so-called
Sivers TMD PDF that describes the modification of the
fully unpolarized TMD PDF when considering unpolarized partons inside of a transversely polarized nucleon [1].
The knowledge of the Sivers PDF is crucial in our understanding of the spin structure of the nucleon. It can be
accessed in a variety of experiments in the so-called deep
inelastic scattering (DIS) regime, where the probes intact
directly with a parton inside of the target, such as the
Drell-Yan process and semi-inclusive hadron production
in polarized hadron-hadron collisions, or semi-inclusive
DIS (SIDIS) of a lepton off a transversely polarized nucleon.
In a SIDIS process with a single detected final state
hadron, the Sivers PDF can be accessed through a term
in the single spin asymmetry (SSA) modulated with the
sine of the so-called Sivers angle [2], defined as the azimuthal angle between the transverse momentum of the
detected hadron and the transverse spin of the nucleon.
The amplitude of this modulation is given as a convolution of the Sivers PDF with the TMD unpolarized
fragmentation function (FF) divided by a convolution of
the unpolarized TMD PDF and TMD FF. Experimental measurements of these asymmetries have been performed by several collaborations: HERMES [3, 4], COMPASS [5, 6] and JLab HALL A [7], extracting sizable effects for both pion and kaon final states. The Sivers PDF
has then been extracted in Refs. [8, 9] using phenomenological parametrizations of the involved PDFs and FFs
to fit the experimentally measured SSAs. Unfortunately
these parametrizations suffer from relatively large uncertainties arising from both theory and experiment. These
uncertainties come from the experimental measurements
themselves, the lack of knowledge of unpolarized TMD
FFs (especially those for the unfavored channels [10], as
well as those involving the strange quark [11]), and assumptions about the shape and the flavor dependences
of both unpolarized and Sivers PDFs and unpolarized
FFs. This is relevant, as in calculating SSAs one integrates over the transverse momentum and then sums over
the type of struck parton. Moreover, in such extractions
Prepared for submission to JHEP
arXiv:1502.02667v1 [hep-ph] 9 Feb 2015
LUX likelihood and limits on spin-independent and
spin-dependent WIMP couplings with LUXCalc
Christopher Savagea,b Andre Scaffidic Martin Whitec Anthony G. Williamsc
a
Department of Physics & Astronomy, University of Utah, Salt Lake City, UT 84112
Nordita, KTH Royal Institute of Technology and Stockholm University, SE-106 91 Stockholm,
Sweden
c
ARC Center of Excellence for Particle Physics at the Terascale & CSSM, Department of Physics,
University of Adelaide
b
E-mail: chris@savage.name, andre.scaffidi@adelaide.edu.au,
martin.white@adelaide.edu.au, anthony.williams@adelaide.edu.au
Abstract: We present LUXCalc, a new utility for calculating likelihoods and deriving
WIMP-nucleon coupling limits from the recent results of the LUX direct search dark matter
experiment. After a brief review of WIMP-nucleon scattering, we derive, for the first time,
LUX limits on the spin-dependent WIMP-nucleon couplings over a broad range of WIMP
masses, under standard assumptions on the relevant astrophysical parameters. We find
that, under these and other common assumptions, LUX excludes the entire spin-dependent
parameter space consistent with a dark matter interpretation of DAMA’s anomalous signal,
the first time a single experiment has been able to do so. We also revisit the case of
spin-independent couplings, and demonstrate good agreement between our results and the
published LUX results. Finally, we derive constraints on the parameters of an effective
dark matter theory in which a spin-1 mediator interacts with a fermionic WIMP and
Standard Model fermions via axial-vector couplings. A detailed appendix describes the use
of LUXCalc with standard codes to place constraints on generic dark matter theories.
Recoil-α-fission and recoil-α-α-fission events observed in the reaction
48
Ca+243 Am
U. Forsberg,1 D. Rudolph,1 L.-L. Andersson,2 A. Di Nitto,3 Ch.E. D¨
ullmann,2,3,4 J.M. Gates,5 P. Golubev,1
5
6
7
2,4
K.E. Gregorich, C.J. Gross, R.-D. Herzberg, F.P. Heßberger, J. Khuyagbaatar,2 J.V. Kratz,3 K. Rykaczewski,6
L.G. Sarmiento,1 M. Sch¨
adel,4,8 A. Yakushev,4 S. ˚
Aberg,1 D. Ackermann,4 M. Block,4 H. Brand,4 B.G. Carlsson,1
7
2,3
9
D. Cox, X. Derkx, J. Dobaczewski, K. Eberhardt,2,3 J. Even,2 C. Fahlander,1 J. Gerl,4 E. J¨ager,4 B. Kindler,4
J. Krier,4 I. Kojouharov,4 N. Kurz,4 B. Lommel,4 A. Mistry,7 C. Mokry,2,3 W. Nazarewicz,6,9,10 H. Nitsche,5
J.P. Omtvedt,11 P. Papadakis,7 I. Ragnarsson,1 J. Runke,4 H. Schaffner,4 B. Schausten,4 Yue Shi,6,10
P. Th¨
orle-Pospiech,2,3 T. Torres,4 T. Traut,3 N. Trautmann,3 A. T¨
urler,12 A. Ward,7 D.E. Ward,1 N. Wiehl,2,3
1
Lund University, 22100 Lund, Sweden
Helmholtz Institute Mainz, 55099 Mainz, Germany
3
Johannes Gutenberg-Universit¨
at Mainz, 55099 Mainz, Germany
4
GSI Helmholtzzentrum f¨
ur Schwerionenforschung GmbH, 64291 Darmstadt, Germany
5
Lawrence Berkeley National Laboratory, Berkeley, California 94720, USA
6
Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831, USA
7
University of Liverpool, Liverpool L69 7ZE, United Kingdom
Advanced Science Research Center, Japan Atomic Energy Agency, Tokai, Ibaraki 319-1195, Japan
9
University of Warsaw, 00681 Warsaw, Poland
10
University of Tennessee, Knoxville, Tennessee 37996, USA
11
University of Oslo, 0315 Oslo, Norway and
12
Paul Scherrer Institute and University of Bern, 5232 Villigen, Switzerland
(Dated: February 11, 2015)
arXiv:1502.03030v1 [nucl-ex] 10 Feb 2015
2
8
Products of the fusion-evaporation reaction 48 Ca + 243 Am were studied with the TASISpec set-up
at the gas-filled separator TASCA at the GSI Helmholtzzentrum f¨
ur Schwerionenforschung. Amongst
the detected thirty correlated α-decay chains associated with the production of element Z = 115,
two recoil-α-fission and five recoil-α-α-fission events were observed. The latter are similar to four
such events reported from experiments performed at the Dubna gas-filled separator. Contrary to
their interpretation, we propose an alternative view, namely to assign eight of these eleven decay
chains of recoil-α(-α)-fission type to start from the 3n-evaporation channel 288 115. The other three
decay chains remain viable candidates for the 2n-evaporation channel 289 115.
PACS numbers: 21.10.-k,23.20.Lv,23.60+e,27.90.+b
In the quest for enhanced nuclear stability in the region of superheavy elements (SHE) – frequently defined
as those with Z ≥ 104 – the two elements flerovium (Fl,
Z = 114) and livermorium (Lv, Z = 116) have recently
been officially approved [1]. The interpretation of data
on odd-Z elements, however, is more challenging, while
the study of nuclei with odd numbers of nucleons can be
especially rewarding: The extra hindrance and thus delay
for spontaneous fission (SF) renders other decay modes
such as α decay and electron capture (EC) even more
likely. Consequently, odd-Z nuclei potentially give rise
to decay chains with more α-decay members than evenZ ones. Additionally, α decay of odd-A or odd-odd nuclei
most often proceeds into excited states in the daughter
nucleus, because unpaired nucleons typically tend to remain in the same single-particle orbitals as in the α-decay
parent [2, 3]. Observation of electromagnetic decays from
these excited states can thus elucidate the low-lying nuclear structure of the daughter [4]. Such experimental
studies have recently reached decay chains of element
Z = 115 [5], while observations of odd-Z elements beyond Rg have been reported up to Z = 117. See, e.g.,
Refs. [6–12] and references therein.
The expected complex nuclear structure of odd-Z nuclei of SHE can easily translate into complex α-decay
sequences. Interestingly, however, for the description of
many of the hitherto published Z ≥ 113 decay chains it
appears to suffice with just one type of α-decay sequence
per isotope, be it 278 113 [12], 287−289 115 [9], or 293,294 117
[10, 11] (see also references therein). This simple but surprising picture might be due to limited statistics, combined with possibly comparable decay energies and half
lives of different decay branches of a given isotope.
In this paper, new data on recoil-α-(α)-SF events
stemming from element Z = 115 are presented. A
comprehensive assessment including corresponding data
from Ref. [9] implies more complex decay sequences of
288,289
115 than presented in previous reports on these isotopes [8, 9, 13]. It is demonstrated that the plain length
of an α-decay chain is not necessarily a good descriptor
to define the reaction channel.
The Universal Linear Accelerator (UNILAC) at the
GSI Helmholtzzentrum f¨
ur Schwerionenforschung, Darmstadt, Germany, provided a 48 Ca8+ heavy-ion beam with
a typical intensity of 6 × 1012 ions per second, averaged
over the pulsed structure of the UNILAC (5 ms beam
on and 15 ms beam off). The experiment was conducted
at two beam energies: Beam integrals of 2.13(12) and
3.89(23) × 1018 48 Ca ions were collected at 5.400 and
5.462 MeV/u, respectively.
Flavor decomposition of the nucleon electromagnetic form factors at low Q2
I. A. Qattan,1 J. Arrington,2 and A. Alsaad3
1
Khalifa University of Science, Technology and Research,
Department of Applied Mathematics and Sciences, P.O. Box 127788, Abu Dhabi, UAE
2
Physics Division, Argonne National Laboratory, Argonne, Illinois, 60439, USA
3
Jordan University of Science and Technology, Department of Physical Sciences, P.O. Box 3030, Irbid 22110, Jordan
(Dated: February 11, 2015)
arXiv:1502.02872v1 [nucl-ex] 10 Feb 2015
Background The spatial distribution of charge and magnetization within the proton is encoded in the elastic form factors.
These have been precisely measured in elastic electron scattering, and the combination of proton and neutron form factors
allows for the separation of the up- and down-quark contributions.
Purpose In this work, we extract the proton and neutron form factors from world’s data with an emphasis on precise new
data covering the low-momentum region, which is sensitive to the large-scale structure of the nucleon. From these, we
separate the up- and down-quark contributions to the proton form factors.
Method We combine cross section and polarization measurements of elastic electron-proton scattering to separate the proton
form factors and two-photon exchange (TPE) contributions. We combine the proton form factors with parameterization
of the neutron form factor data and uncertainties to separate the up- and down-quark contributions to the proton’s
charge and magnetic form factors.
Results The extracted TPE corrections are compared to previous phenomenological extractions, TPE calculations, and direct
measurements from the comparison of electron and positron scattering. The flavor-separated form factors are extracted
and compared to models of the nucleon structure.
Conclusions With the inclusion of the precise new data, the extracted TPE contributions show a clear change of sign at low
Q2 , necessary to explain the high-Q2 form factor discrepancy while being consistent with the known Q2 → 0 limit. We
find that the new Mainz data yield a significantly different result for the proton magnetic form factor and its flavorseparated contributions. We also observe that the RMS radius of both the up- and down-quark distributions are smaller
than the RMS charge radius of the proton.
PACS numbers: 25.30.Bf, 13.40.Gp, 14.20.Dh
I.
INTRODUCTION
The electromagnetic form factors of the proton and
(p,n)
(p,n)
neutron, GE
and GM , are fundamental quantities
which provide information on the spatial distributions of
charge and magnetization in nucleons. The form factors
are measured using electron scattering where the incident
electron scatters from a nucleon target through the exchange of a virtual photon which serves as the sole mediator of the electron-nucleon electromagnetic interaction.
By increasing Q2 , the four-momentum squared of the virtual photon, the virtual photon becomes more sensitive
to the small scale internal structure of the nucleon.
In electron scattering there are primarily two methods used to extract the proton form factors. The first is
the Rosenbluth or Longitudinal-Transverse (LT) separation method [1], which uses measurements of the unpolarized cross section, and the second is the polarization
transfer or polarized target (PT) method [2], which requires measurement of the spin-dependent cross section.
A significant difference is observed between LT and PT
extractions of the proton form factors [3, 4], which is currently believed to be the results of larger-than-expected
two-photon exchange (TPE) contributions [5, 6].
In this paper, we extract the proton form factors from
a combined analysis of LT and PT measurements, accounting for TPE contributions following the approach
of Ref. [7], but with an emphasis on recent low-Q2 data.
The combined analysis allows us to extract the TPE contribution to the e-p elastic cross section, which we compare to other phenomenological extractions and to direct calculations of TPE effects meant to be valid in the
lower Q2 regime, as well as to recent direct measurements
of TPE contributions from the comparison of electronproton and positron-proton elastic scattering [8, 9].
With the inclusion of neutron form factor measurements, we separate the nucleon form factors into their upquark and down-quark contributions [10, 11]. New cross
section and polarization measurements at low Q2 allow
for a more detailed examination of the flavor-separated
form factors in the region sensitive to the large-distance
behavior of the proton charge and magnetization distributions. We compare these results to previous extractions, as well as to models of the up- and down-quark
contributions to the proton form factors.
II.
OVERVIEW OF THE METHODS
A.
Rosenbluth Separation Method
In the Rosenbluth separation method, the reduced
cross section σR for elastic e-p scattering in the Born
or one-photon exchange (OPE) approximation is:
2 ε
2
σR = GpM (Q2 ) + GpE (Q2 ) ,
τ
(1)