1. science
2. biology
3. marine biology

Sikafloor® Marine Technology
Pre-Treatment Chart for
®
Sikafloor Marine Products
Version 1 (11/2011)
Recommendations for Sikafloor® Marine Range
Products PU-Red
Self-levelling mortar:
(Visco elastic) Sikafloor® Marine 100
Sikafloor® Marine 120
Trowel out levelling mortar:
Sikafloor® Marine KG-202 N
Sikafloor® Marine KG-404 N
Substrates
Steel Deck
B C /V
Steel Deck with
zinc Primer
1
Sikafloor® Marine 18
Sikafloor® Marine
KG-202 N
Sikafloor® Marine
KG-404 N
1
Sikafloor®
Marine Litosilo N
PU-Red
Sikafloor®
Marine 18
(Trowel out
levelling mortar)
Sikafloor®
Marine
Thermo-light
(2 layer levelling system)
B C /V
PC
B C /V
before Rockwool
B C /V
PC
B C /V
PC
1 2
Aluminium Deck
Sikafloor®
Marine Litosilo N
(Trowel out
levelling mortar)
Sikafloor®
Sikafloor®
Marine Elastic Marine E-43
(Water proofing (Epoxy floor)
mortar)
Cleaning and
Shopprimer
GR
ZP
B C /V
GR
ZP
B C /V
PC
B C /V
before Rockwool
GR
ZP
B C /V
PC
GR
ZP
B C /V
PC
GR
ZP
PC
1
GR
ZP
B C /V
GR
ZP
B C /V
PC
B C /V
before Rockwool
GR
ZP
B C /V
PC
GR
ZP
B C /V
PC
GR
ZP
PC
3
GR
PC
B C /V
GR
PC
B C /V
GR
PC
B C /V
GR
PC
B C /V
GR
PC
B C /V
GR
B C /V
GR
PC
B C /V
GR
PC
B C /V
GR
PC
B C /V
GR
PC
B C /V
GR
PC
B C /V
GR
B C /V
2
B C /V
Application Temperature: 5 – 35 °C, (40 – 95 °F)
1
2
3
If the deck is contaminated with oil, grease or similar use Sika Remover®-208 prior to Primer C / PU-Red
Remove any loose rust prior to use of Primer C / PU-Red
Please contact local Technical Departement of Sika Industry
Abbreviation
Product/Explanation
No special pre-treatment required
BC/V
Broom Cleaning or Vacuum Cleaning
PC
Sika® Primer-C
GR
Grinding (40 grit)
ZP
SikaCor® ZP-Primer
n.a.
Not applicable
Legal Note
The information contained herein and any other advice are given in good faith based on Sika‘s
current knowledge and experience of the products when properly stored, handled and applied
under normal conditions in accordance with Sika‘s recommendations. The information only applies
to the application(s) and product(s) expressly referred to herein and is based on laboratory tests
which do not replace practical tests. In case of changes in the parameters of the application,
such as changes in substrates etc., or in case of a different application, consult Sika‘s Technical
Service prior to using Sika products. The information contained herein does not relieve the user of
the products from testing them for the intended application and purpose. All orders are accepted
subject to our current terms of sale and delivery. Users must always refer to the most recent issue
of the local Product Data Sheet for the product concerned, copies of which can be downloaded on
your local sika company website or will be supplied on request.
Utilisation of Sika Pre-Treatment Chart
Information about the pre-treatment of surfaces in this document serves as a guideline only and must be verified by tests on original
substrates. Project specific pre-treatment recommendations, based on laboratory tests, are available from Sika on request.
SikaCor® ZP-Primer
Colour
Component A:
grey or red
Type of product
Component B:
pale yellow
Sikafloor® Marine Primer-C
Sika® Remover-208
White
Transparent
Primer
Remover
Application temperature
10 – 35 °C (50 – 95 °F)
5 – 35 °C (40 – 95 °F)
5 – 40 °C (40 – 105 °F)
Application
Brush, Roller
Roller
Wipe-on, Wipe-off with Lint-Free
Paper Towel
Material consumption on:
– steel
– mortar layers
200g/m2 approx. by brush or roller
No use of SikaCor® ZP-Primer on this substrate
75 g/m2 approx.
150 – 300 g/m2 approx.
40/m2 approx. depending on
contamination
10 °C (50 °F): minimum 5 h to maximum 14 h
30 °C (86 °F): minimum 2 h to maximum 14 h
20 °C (68 °F): minimum 3 h to maximum 14 h
2 h to 3 h
30 min. to max. 24 h
Flash-off time
Notice:Sika® Remover and Primers are moisture reactive systems. In order to maintain product quality it is important to reseal the container immediately after
use. With frequent use i.e. opening and closing several times, we recommend to dispose of the product one month after opening. With infrequent use,
we recommend to dispose of the product 2 months after opening.
Sika Services AG
Business Unit Industry
Tuffenwies 16
CH-8048 Zurich
Switzerland
Phone +41 (0) 58 436 40 40
Fax
+41 (0) 58 436 45 64
E-Mailindustry@ch.sika.com
Please consult the most current local
Product Data Sheet prior to any use.
www.sika.com