1. home and garden
2. home furnishings
3. lamps and lighting

ZBARLED300 / ZBARLED1000 WIRING INSTRUCTIONS & GUIDELINES
Technical Overview
Rotary Controller Operation
The ZBARLED will dim a variety of loads, primarily LED, but also
CFL and Tungsten. The advanced technology used to control the
waveform results in flicker free* dimming of leading and trailing
edge dimmable lamps & drivers. It is designed to fit both new
and existing installations.
Push on and off, turn control knob clockwise to increase light level,
anti-clockwise to decrease light load. Note : When dimming your
lights with multiple rotary controllers the light levels are adjusted
from the last setting selected at that switch point.
The product has built in thermal protection and will automatically
reset when cool. It also has built in short circuit and overload
protection if the unit detects a fault it will automatically shut
down and will require the supply being switched off and the fault
rectifying before switching on the supply.
Control of the unit can be made via a rotary controller (part
number ZBARROT), where up to 32 rotary controllers can be
connected in parallel to one ZBARLED. Alternatively, control
can be made via two different types of push to make retractive
switches; the first type being push to make only, the second type
being a rocker push up and down. Each controller or switch may
be connected on existing twin and earth wiring.
* Zero flicker on all tested lamps.
PRODUCT REF
TYPE
Setting the minimum level pre-set (MLP)
•Turn light on and turn control knob fully clockwise
for full brightness.
•Press to turn off.
•Turn control knob fully anti clockwise and press to turn on, the
lights will then flash and the dimmer is in programming mode.
•Rotate the control knob to adjust the light level.
•Once you have achieved the desired minimum level, leave the
control knob for 5 seconds and the lights will then flash, the
dimmer has then stored the minimum level.
INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
•This product must be installed in accordance with the relevant wiring regulations.
•Switch off mains supply
ZBARLED300
ZBARLED1000
IN-LINE REMOTE PACK
IN-LINE REMOTE PACK
LAMP TYPE
T / LV / LED / CFL
T / LV / LED / CFL
MAX WATT
300 / 300 / 300 / 300
1000 / 1000 / 1000 / 1000
MIN WATT
0/0/0/0
0/0/0/0
SIZE (MM)
126 X 51 X 34 appx.
126 X 51 X 34 appx.
General Wiring Diagram
•Decide on a suitable location for the dimmer pack with
adequate ventilation and ensure the dimmer is mounted
away from insulation
•If multiple units are mounted within close proximity,
ensure a 15mm gap between units
•Commence connections as per appropriate wiring diagrams and in accordance with the relevant wiring regulations
•Incorrect wiring may result in product failiure and / or
irreperable damage to the product.
Wiring With Retractive Push Up/Down Switches
IMPORTANT! No Connection, Terminate
in a suitable connector to isolate
SUPPLY
ZBARLED
MULTI - POINT
DIMMER
LIGHTING
JOINT BOX
LAMPS
ZBARLED
Multi Point
Remote
Dimming
Pack
LAMPS
NC
NC
ROTARY/
RETRACTIVE
SWITCHES
Permanent Live
RETRACTIVE
PUSH
UP/DOWN
SWITCHES
RETRACTIVE
PUSH
UP/DOWN
SWITCHES
Continue
to add
switches
as required
Wiring With Rotary Controllers
Wiring With Retractive Push Switches
IMPORTANT! No Connection, Terminate
in a suitable connector to isolate
IMPORTANT! No Connection, Terminate
in a suitable connector to isolate
LAMPS
ZBARLED
Multi Point
Remote
Dimming
Pack
LAMPS
ZBARLED
Multi Point
Remote
Dimming
Pack
NC
NC
Suitable Twin & Earth
ROTARY
CONTROLLER
ROTARY
CONTROLLER
Add up to 32
controllers
as required
RETRACTIVE
PUSH
SWITCHES
RETRACTIVE
PUSH
SWITCHES
Continue
to add
switches
as required
Permanent Live
Retractive / Push To Make Single Switch Operation
•A brief press of the switch will bring the lights on or off.
•Push and hold the switch and the light level will increase
until they reach maximum.
•Release the switch, push and hold again.
•The light level will decrease until they reach the minimum.
•A single press will turn the lights on or off.
•The lights will come on at their last setting.
•You are now in programming mode.
•Adjust light level by pressing the switch.
•You can press the switch as many times as you like. Each time
the switch is pressed, the lights will dim in the opposite direction.
If the switch is not pressed for a period of 5 seconds the lights will
flash and the dimmer is out of programming mode.
Retractive Up & Down Switch Operation
Setting the minimum level pre-set (MLP)
•As above, but with the added feature of having a
separate switch for up and down.
The lights will dim down. Hold the switch in for a further
5 seconds, the lights will then flash.
Setting the minimum level pre-set (MLP)
Zano Controls
Guarantee
Zano Controls produces a range of dimmer switches and lighting
control systems. For our full range of products see our website
or pick up a brochure from one of our stockists.
1. The Company guarantees at its entire discretion either to
replace or repair any of the Goods which within the Guarantee
period of the Goods are shown to its satisfaction to be defective
through faulty material or workmanship alone, provided that
no attempt has been made by the Customer or a third party to
rectify, dismantle or alter the Goods in any way.
•Press and hold the switch until the lights are at maximum.
•Release the switch, instantly push and hold the switch again.
•As above, but using the separate switch position for up and down.
2. The Guarantee period for any Goods is as specified at the time in
the Company’s catalogue current at the time of acceptance of the
Customer order and commences on the delivery of the Goods.
Contact us at Zano Controls
Unit 1 Chantry Court,
Wrythe Lane,
Carshalton,
Surrey,
SM5 2DG
Tel : 0845 519 5858
Fax: 0845 519 5757
sales@zanocontrols.co.uk
www.zanocontrols.co.uk
3. All terms, conditions , warranties, or representations, whether
expressed or implied, as to description, condition, quality or fitness
for purpose of any of the Goods are hereby excluded.
4. So far as permitted by statue, the Company shall not be liable
for loss or damage whether direct or consequential and whether
suffered by or occasioned to the Customer, it’s employees or
agents or to any third party. Our full terms and conditions can be
found on our website www.zanocontrols.co.uk.
Designed &
Built in the U.K
Terms & conditions apply, please see our website www.zanocontrols.co.uk
For further safety & certification information see www.zpatent.co.uk
Certification No.188763
IZBARLED1000 / 15/10/14