1. technology and computing
2. consumer electronics
3. camera and photo equipment
4. cameras and camcorders
5. cameras

AVWARE AVW643L45LC
Features
■
1/3" SONY SuperHAD CCD Ⅱ (Min. Illumination)
■
Privacy Masking(8 Zone Selectable)
1
Drawing
2
■ Motion Detection(4 Zone Selectable)
■
3DNR(Digital Noise Reduction) / D - WDR
■
Multi Language (Korean,English,chinese,Japanese)
SR LEDs 20EA +
IR LEDs 25EA
Total 45EA LEDs
Specification
Item
AVW643L45LC
Imaging Sensor
1/3" New SONY Super HAD CCD Ⅱ Dy namic
NTSC : 525 Lines
PAL : 625 Lines
Signal System
Scanning System
2:1 Interlace
Scanning Frequency
H:15.734 ㎑ / V:59.94 ㎐
H:15.625 ㎑ / V:50 ㎐
More than 52㏈ (AGC Off)
600 TV-Line (Color)[Min] / 700 TV-Line (B/W)[Min]
S/N Ratio
Horizontal Resolution
Video Output Level
Set up and
Function
1.0 Vp-p (75Ω , Composite)
Built-in DC Iris Vari-focal Lens (6~50mm, F=1.4)
Lens
Min. Illumination
Color : 0.03Lux(50IRE@F1.2) , 0.00019(Sens-up.256x)
Sync System
Internal / Line Lock(Dual Option)
O.S.D
Built-in(Multi-Language Support)
Electronic Shutter Speed
WIDE / TELE
NEAR / FAR
Auto / Flk
(NTSC : 1/60sec ~ 1/100,000sec)
White Balance
VBS-EXTERNAL RCA
(PAL : 1/50sec ~ 1/100,000sec)
AWB / AWC-SET / MANUAL / INDOOR / OUTDOOR/ATW
Backlight Compensation
OSD FUNCTIOM JOYSTICK
BLC / HS.BLC / Off
D - WDR
LED SELECTABLE S/W
- UP : LOW
- DOWN : HIGH
INDOOR / OUTDOOR / Off
Gain Control
Low / Middle / High / Off
Adjust
CONTRAST/SHARPNESS/CB_GAIN/CR_GAIN (Level Adjustable)
Language
Korean / English / Chinese / Japanese (Selectable)
Camera Title
On / Off (Selectable)
Day & Night
Auto / B.W / Color (Selectable) / EXT
Digital Zoom
On / Off(0x ~ 32x)
Privacy Masking
▶ L ED L OW/ HI GH SEL ECT A BL E S/ W
- LOW : Turn OFF The SRLED
- HIGH : Turn ON The SRLED & IRLED
On / Off (8 Zone Selectable)
3DNR (Digital Noise Reduction
On / Off(Selectable)
Sens - up(Frame Integration)
D - EFFECT
▶ V BS- EXT ERNA L RCA OUT
- Video signals are output through this RCA type Port. Connect this port(VBS-External)
to the Video IN port of a monitor
On / Off(Selectable limit ~ 256x)
Freeze / Mirror / D-Zoom / Gamma / NEG.IMAGE
Visibility Ranre
▶ OSD FUNCT I OM BUT T OM
- SET Button : Displays the menu on the screen. Press the button to confirm status or
Indoor 80m / Outdoor 70m
IR LED
after changing a selected item.
850nm SRLED 20EA / 850nm IRLED 25EA TOTAL:45EA
Supplied Voltage
- Up and Down Button : Used to move the cursor up or down in the menu screen to select
DC12 ±10%
Power Consumption
a desired menu item.
IR LED OFF : 120㎃ / IR LED ON : 600㎃ (max.)
Dimension
- Left and Right Button : Used to move the cursor left or right in the menu screen or to
93(W)×95(H)×160(D)mm
Weight
change the value of the selected item.
Approx. 1.26㎏
■ Function Menu
3
Function Menu
LENS
EXPOSURE
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 'EXPOSU RE' by usi ng U p and
Dow n but t ons. So t hat t he ar r ow i ndi cat es t he 'EXPOSU RE'.
■ DC
2. Sel ect a desi r ed mode usi ng t he U p and Dow n but t ons.
▶ SH U T T ER : You can select either auto or manual shutter.
■ SHUTTER
■ BRIGHTNESS
■ AGC
■ SENSE-UP
■ BLC/HSBLC
■ D-WDR
- FL K : Select this when you experience picture flicker
■ AWB
■ AWC→SET
■ MANUAL
- A U T O : Select this mode to control the shutter speed automatically.
■ INDOOR
■ OUTDOOR
■ ATW
DAY NIGHT
■ COLOR
■ AUTO
■ EXT
■ B/W
▶ BRI GH T N ESS : You can control the brightness by using the Left and Right button in
3 DNR
■ ON
■ OFF
■ CAM TITLE
■ D-EFFECT
■ RS485
■ MOTION
▶ A GC : You can adjust it Low, Middle and High level.
EXPOSURE
WHITE BAL
SPECIAL
Shutter speed is automatically controlled depending on the brightness of the screen.
Manual Lens mode.
■ PRIVACY
■ SYNC
■ LANGUAGE
ADJUST
■ SHARPNESS
■ BLUE
■ RED
RESET
■ FACTORY
EXIT
The higher the gain level, the brighter the screen but the higher the noise.
▶ SEN SE- U P : When it is night of dark, the camera automatically detects the light level and
maintains a clear pictur.
▶ BL C : This function allows you to get a clear pictures of objects even the objects in strong backlight.
- BL C : Enables a user to directly select a desired area from a picture, and to view the area more clearly.
How to use the
Notes
⊙ All item with the
, you can move to sub menu pressing SET button.
⊙ An item with the - - -, icon is unavailable due to function settings
L ENS
● Using t his f unct ion, y ou can cont r ol scr een br ight ness
1 . When t he SET UP menu scr een is display ed, select 'L ENS' by using t he Up and
- H S- BL C : If there is a high light installed in a limited environment such as an apartment
parking garage or gas station entrance, removing the hight light makes
it possible to view car license plates efficiently.
▶ SEN SE- U P : When it is night of dark, the camera automatically detects the light level and
maintains a clear picture.
Notes
This function Deactivates when the AGC "OFF", DAY&NIGHT "OFF"
OFF : Deactivates the Sense-up function.
AUTO : You can adjust brightness by increasing or decreasing the shutter speed(X2~X256)
* Note that the higher the zoom level, the brighter the screen, but the more likely it
is that an after-image will appear.
* Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the zoom
level is increased, this is normal.
Dow n but t ons so t hat t he ar r ow indicat es 'L ENS'.
2 . Select t he connect ed t y pe by using L ef t and Right but t ons
- DC : Select Auto Iris Lens
When DC is selected, you can control screen brightness. The range of brightness
control is between 0 and 100.
Adjust the brightness appropriately for optimal screen brightness.
HS BLC OFF
- DA Y
- N I GH T
HS-BLC ON
: Even in normal daylight conditions, the HS-BLC is activated.
: If a high light that is larger than certain size is present on the screen
remove the high light to see car license plates clearly.
- Enable a user to select a mask of high light area
from a picture.
copyright www.avware.de
4
▶ D- WDR : If there are bright area and dark area on the screen at the same time,
this function makes both areas to be in clear image
5
- D-WDR can be selected 3 steps OFF / INDOOR / OUTDOOR
3 Digit al Noise Reduct ion( 3DNR)
● T hi s f unct i on r educes t he back gr ound noi se i n a l ow l umi nance env i r onment
6
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 3DN R by usi ng t he U p and
Dow n but t ons so t hat t he ar r ow i ndi cat es 3DN R.
2. Sel ect a desi r ed mode usi ng t he L ef t and Ri ght but t ons.
▶ OFF : Deactivates 3DNR. Noise is not reduced.
▶ ON : Activates 3DN so that noise is reduced.
D-WDR ON
WHI T E BA L A NCE ( Whit e Bal.)
D-WDR OFF
3. Set t he 3DN R mode t o 'ON ' andpr ess t he SET but t on. T hen y ou can adj ust t he
N oi se r educt i on l ev el .
1. When SET U P menu scr een i s di spl ay ed, sel ect 'Whi t e Bal .' by usi ng U p and
Notes
Dow n but t ons so t hat t he ar r ow i ndi cat es Whi t e Bal .
⊙ You cannot set the 3DNR to 'ON' or 'OFF' when the AGC mode of the EXPOSURE menu is
'OFF'.
⊙ When adjusting the noise reduction level of the 3DNR mdoe, the higher the level set ,
the more the noise level will be reduced but that after image may also occur.
※ Sel ect one of t he f ol l ow i ng 6 modes, as appr opr i at e f or y our pur pose
▶ A WB : Select this when the color temperature is between 2,000ºK and 18,000ºK.
▶ A WC- > SET : To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press
the SET button. If the environment changes, readjust it.
SPECI A L
▶ M A N U A L : Select this to fine-tune White Balance manually. Set White Balance first by using
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 'SPECI A L ' by usi ng U p and
the ATW or AWC mode. After that switch to MANUAL mode.
Dow n but t ons so t hat t he ar r ow i ndi cat es 'SPECI A L '
Adjust the [BLUE] and [RED], according to the changing of color on the screen
2. Sel ect a desi r ed mode usi ng t he U p and Dow n but t ons
▶ I N DOOR : Select this when the color temperature is around 3,100ºK.
▶ CA M T I T L E : If you enter a title, the title will be appear on the monitor.
① If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow
▶ OU T DOOR : Select this when the color temperature is around 5,100ºK.
indicates 'CAM TITLE'
▶ A T W : Select this when the color temperature is between 2,500ºK and 9,800ºK.
② Set it to 'On' by using Left and Right buttons.
Notes
Notes
⊙ White balance may not work properly under the following conditions.
In this case, select the AWC mode.
① When color temperature of environment surrounding the subject is out of the control range
⊙ When the CAM TITLE menu is 'OFF', no title will be displayed on the monitor screen even if
you
③ Press the SET button.
DA Y/ NI GHT
④ Use the 4 direction buttons to move to a desired letter and select the letter by pressing the
● You can di spl ay pi ct ur es i n Col or or Bl ack and Whi t e.
SET button. Repeat this to enter multiple letters. You can enter up 15 letters.
1. When t he SET U P menu scr een i s di spl ay ed, sel ect 'DA Y/ N I GH T ' by usi ng t he U p
Notes
and Dow n but t ons so t hat t he ar r ow i ndi cat es 'DA Y/ N I GH T '
⊙ If you entered wrong letter……
If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit a
leeter,
change the cursor to the bottom left arrow and press the SET button. Move the curson over
▶ COL OR : The picture is always displayed in color.
▶ A U T O : The mode is switched to color in a normal environment, but switches to B/W mode
when ambient illumination is low. To set up the switching time or speed
for auto mode, press the SET button
⑤ Enter a title, move the cursor to 'POS' and press the SET button. The entered title appears
- Delay : You can select the duration time about changing the day/night mode.
on the screen. Select the position to display the title on the screen by using the 4 directoin
- S / E - Level : You can select brightness of illumination about changing the day/night mode.
buttons and press the SET button. When the position is determined, select 'END' and press
-> The brightness of illumination is changeable by installed environment.
the SET button to return to the SPECIAL menu.
▶ EXT : Deactivates the EXT function. (The picture is always displayed in B/W)
▶ D- EFFECT
▶ BW : The picture is always displayed in B/W.
① When the SPECIAL menu screen is displayed, press the Up and down buttons so that the
arrow indicates "D-EFFECT".
Notes
② Press the SET button for Sub menu.
⊙ You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is 'OFF'
At this time, the exchange between DAY mode and NIGHT mode operates as COLOR mode
* Mirror
- Mirror : you can flip the image vertically on the screen.
- Rotate : you can flip the imate horizontally on the screen.
- V-Flip : you can flip the image vertically and horizontally both.
* Digital Zoom : You can use a digital zoom of x1.0 ~ X32
* Freeze : You can stop the image or reactivate it.
7
▶ PRI V A CY : Hide an area you want to hide on the screen.
① When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the
arrow indecates 'PRIVACY'.
② Press SET button for Sub Menu.
③ Set up the mode by using 4 direction buttons.
* Gamma : Standard value is 0.45. You can adjust the value between 0.05 ~ 1.00
* AREA SELECT : You can select up to 8 privacy areas.
* NEG IMAGE : you can flip the color on screen.
* AREA DISPLAY : Determines whether to use the area selected in the AREA SELECT.
▶ RS 485 : Deactivates the RS485 function.
* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.
▶ M OT I ON : If you connect an alarm device to this camera, you can monitor activity
* WIDTH : adjust the selected vertical area.
because a signal is generated by the camera whenever motion is detected. The
* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.
motion detection signal is output through the MD OUT port.
* HEIGHT : adjust the selected horizontal area.
① When the SPECIAL menu is displayed, press the
Up and Down buttons so that arrow indicates
* COLOR : Determine area color. You can select 0 ~ 15.
▶ SYN C : In areas where the supply is at 60Hz, you can synchronize the output phase of
MOTION.
multiple cameras using the power synchronization function (Line-Lock) without
② Press SET button for sub menu.
③ Set up the mode using 4 direction buttons.
using a synchronization signal generator
- INT : Internal SYNC type
* AREA SELECT : Determines which 4 vertices of
each MD area is to be used
* AREA DIPLAY : Determines whetehr to use the MD area selected in Sensitivity.
* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.
⊙ When using AC power at 60Hz frequency, you can use the L/L type SYNC
⊙ When the power is DC 12V, the SYNC menu is fixed to the INT mode.
▶ L anguage : You can select the menu language according to your requirement.
* WIDTH : Adjust the selected vertical area.
- It can be changes 5sec. later.
* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.
* HEIGHT : Adjust the selected horizontal area.
* Sensitivity : You can select up to 4 areas. When sensitivity number is high,
motion detection sensitivity is increased to recognize even small movement
- L/L[Line-Lock] : Power SYNC type
Notes
- Supplied Language : English, Chinese, Japanese
A DJUST
1. When t he SET U P menu scr een i s di spl ay ed, sel ect A DJU ST by usi ng U p and
Dow n but t ons so t hat ar r ow i ndi cat es A DJU ST .
▶ Shar pness : As you increase this value, the picture outline becomes stronger and clearer
* Motion View : If you make it ON by using LEFT and RIGHT buttons, selected
value of color is filled on the screen
Notes
⊙ MD areas show only MOTION menu. Therefore, MD areas don't display on the monitor
screen.
⊙ BUT if you select the motion view function ON, MD areas are displayed on the monitor
Adjust this value appropriately depending on the sharpness of the picture.
▶ BL U E : You can adjust the color on the monitor in BLUE mode by controlling between
0 and 100
▶ RED : You can adjust the color on the monitor in RED mode by controlling between
0 and 100
RESET
1. When t he SET U P menu scr een i s di spl ay ed, sel ect RESET by usi ng U p and
Dow n but t ons so t hat ar r ow i ndi cat es RESET .
2. Sel ect a mode by usi ng U p and Dow n but t ons.
▶ FA CT ORY : Resets the camera settings to the factory defaults.
Language and Communication status is not initialized
EXI T
Press the SET button in the Exit menu to save the current settings and exit the Main SETUP
menu.
copyright www.avware.de
8